Search Results for "spi"

Betaflight is flight controller software (firmware) used to fly multi-rotor craft and fixed wing craft. This fork differs from Baseflight and Cleanflight in that it focuses on flight performance, leading-edge feature additions, and wide target support. Betaflight supports a wide range of flight controllers with at least an STM32F4 MCU. You can use nearly any piece of modern hardware out there. Full telemetry and high refresh rate for receivers, camera and VTX control, RGB LEDs, and much...

The Monsputer is a Z80 computer developped with old chips (and some new) collected over the years. It has about 2M memory, clocks at 4.0MHz, has serial ports, 1 parallel port, 1 CAN bus, 2 SPI, 1 I2C, a RTC and other features. It supports interrupts mode 2 but not DMA.

...It can communicate over WiFi through the use of TCP and UDP; it can set up HTTP, mDNS, SSDP, and DNS servers; and it can perform OTA updates. ESP8266 Arduino core works with SD cards, servos, SPI and I2C peripherals.

...The project comprises a main keyboard PCB (STM32F103), a dynamic module (STM32F405) with additional features like an e-ink screen, OLED display and a haptic/motorized knob, a base/dock module with USB hub functionality, and other supporting PCBs. The firmware includes high-speed scanning of keystrokes, RGB lighting control via SPI/DMA, HID keyboard enumeration, multiple key-layer mapping and non-volatile configuration storage. The hardware architecture is modular: the keyboard, dynamic module, and base connect via FFC/contacts so you can swap out the dynamic side module or bottom. The documentation includes 3D models for casing, firmware binaries, and tools for customization.

An STM32 Nucleo-144 development board with Arduino Uno Rev3 connectivity is interfaced via an EastRising Technology Co Ltd Shield PCB to the East Rising 800x480 pixel 7 inch LCD panel with resistive touch screen. A set of functions has been developed to drive the panel via SPI, which uses the RAiO Technology Inc RA8875 TFT-LCD controller IC. Test firmware was developed that uses this function set to explore and demonstrate the many capabilities of the panel. The STM library is used along with FreeRTOS. Please see: LcdTest_ReadMe.pdf or LcdTest_ReadMe.odt. The project is simply a personal record of what has been done, and will not be developed further.

...Non-AVR boards are NOT currently supported (101/Zero/Due) #211 Hardware: Depending on the size of the buffer for packets, this library uses about 1k of Arduino RAM. Large strings and other global variables can easily push the limits of smaller microcontrollers. This library uses the SPI interface of the microcontroller and will require at least one dedicated pin for CS, plus the SO, SI, and SCK pins of the SPI interface. An interrupt pin is not required. Any Arduino IDE >= 1.0.0 should be fine. EtherCard is available for installation in the Arduino Library Manager. Alternatively, it can be downloaded directly from GitHub.

This library controls many Silicon Laboratories Si47xx family radio chips with an Arduino microcontroller. Major features include: • I2C and SPI bus • Supports "original" (Uno, Duemilanove, and their clones), Mega 2560, Leonardo, and Due Arduinos • FM/AM receive modes; including short, medium, and long wave AM • Analog and/or digital audio output • FM RDS and RBDS • Localization of receive bands, channel spacing, FM de-emphasis, and RDS/RBDS • Correctly decodes RBDS PI codes into station's call letters • Can handle a mix of RDS and RBDS stations as found near the US boarders with Canada and Mexico • Example programs I2C and Due support is alpha because I do not have hardware to test these features.

Set of various C-routines for Atmel AVR MCUs, packed in several libraries, with fancy Makefile system for easy integration with user projects. Contains functions for UART, SPI, HD44780 or T6963C LCD\'s, Dallas 1-Wire bus, AVR bootloader and more.

Ddr-Z8E is a device driver library for the Zilog Z8 Encore!(r) microcontroller. The library supports I/O, IRQ, RS-232, I2C, SPI, A/D, WDT, ticker and built in flash memory as well as utility modules, e.g. for debugging and binary number representation.

vport is a universal hardware interface for education and development. It supports all important microcontroller intefaces such as I2C, SPI, JTAG, RS232, IO-Ports, 1-Wire, CAN, ...