Menu
▾
▴
Re: [Sdcc-user] Fw: Silabs IDE
|
From: Maarten B. <sou...@ds...> - 2013-01-05 22:49:42
|
Hi Don, Why do you want to compile the header files? Is that what you do wih Keil too? I think not. It would give a similar error as sdcc does. Header files are not meant to be compiled, they are meant to be included. I think you need to get through some C tutorial first. Probably best not embedded related at all. Greetings, Maarten > Hi Rich > I tried what you said and with that simple program without header files > the unit does seem to compile nicely. So my concern with cygwin was > unfounded. I have been experimenting with the DTMF Generator program that > was originally compiled with Keil. If I use the Keil demo compiler that > comes with my development kit it compiles fine. I can even up load the > code to my development board and that works fine. After getting the test > program to compile I tried loading in the header files one at a time. I > tried to compile the header files alone with SDCC. In both cases I got an > error message as follows: > at 1: warning 119: don't know what to do with file 'c8051F300.h'. file > extension unsupported > > Any idea what I need to do about that? Should I be naming the header file > extension something else that *.h?? > THANX Don Voth > > From: Rich Bayless > Sent: Friday, January 04, 2013 5:12 PM > To: sdc...@li... > Subject: Re: [Sdcc-user] Fw: Silabs IDE > > Hi Don, > > If you'd like to make some progress, try these steps. > > Stop doing anything with cygwin. > > Go to the sdcc site on sourceforge and download the windows > installer for sdcc: > http://sourceforge.net/projects/sdcc/?source=directory > > Just click on the green button that says 'Download'. > > Save the sdcc installer file to your local drive and run the > installer, accept the defaults. > > Make sure you make a note of what folder sdcc was installed into, > such as c:\programs\sdcc or c:\programs (x86)\sdcc. > > Open Silabs IDE and click on Project, Tool Chain Integration, then > near the top, select the drop box arrow next to Preset Name. Select > preset name sdcc 3.x read only and press enter. Click on each of > the three tabs, assembler, compiler, and linker, and verify the path > and program names are correct. > > Next, start a new project, and add a new file. Select the radio > button for 'C Source File', and click OK. In the new file type > something simple like: > > void main(void) > { > > } > > and save the file. > > At this point, you should be able to compile the program for sdcc > from within Silabs. Click on Project, Build/Make, to start > compiling. > > I just did the above steps and the program compiled and linked > successfully. > > Good luck! > > Rich. > > --- On Fri, 1/4/13, jp...@he... <jp...@he...> wrote: > > > From: jp...@he... <jp...@he...> > Subject: Re: [Sdcc-user] Fw: Silabs IDE > To: sdc...@li... > Date: Friday, January 4, 2013, 5:20 PM > > > Hello Don, > > I have no experience with CYGWIN so can't help you there. Why > do'nt you run SDCC in Silabs IDE under Windows 7 ? > > regards > > Co > > > ------------------------------------------------------------------------ > From: iTronix [mailto:it...@my...] > Sent: Fri 12/28/2012 4:19 PM > To: sdc...@li... > Subject: [Sdcc-user] Fw: Silabs IDE > > > HI Guys > Thank you for your input. I think part of the problem is that I am > trying to run the Silab IDE and the SDCC compiler on a Windows 7 > machine and I have no idea how to use cygwin. I have installed > cygwin and can open the little black window with the command > prompt. After that I have no idea what to do? I know nothing about > linix. I do not understand how you can run a Linix program like > SDCC inside a windows 7 programs like Silab IDE? > > The contents of the file cyglink.txt file is the following: > > "C:\Users\Don\Documents\iTech\DTMF Project\DTMF SDCC > Code\generator\dtmfgen.obj" TO( > "C:\Users\Don\Documents\iTech\DTMF Project\DTMF SDCC > Code\generator\DTMF Generator SDCC" ) RS(256) PL(68) PW(78) > LIBPATH(C:\Program Files (x86)\SDCC\lib) > This file is created when I run the SDCC compiler in the Silabs > IDE. > > Any more help would be much appreciated. Remember I am a Newbie to > compiling. The last time I did microcontroller development work we > were using assembler language. > THANX Don Voth > > > From: wlmailhtml:/mc/compose?to=jp...@he... > Sent: Friday, December 28, 2012 8:03 AM > To: wlmailhtml:/mc/compose?to=sdc...@li... > Subject: Re: [Sdcc-user] Silabs IDE > > I'm using the sdcc with SILABS IDE for several years now and never > encountered a problem with SDCC. > > Regards > > Co poppe > > > ------------------------------------------------------------------------ > > From: Rich Bayless [mailto:ric...@at...] > Sent: Tue 12/25/2012 7:19 PM > To: wlmailhtml:/mc/compose?to=sdc...@li... > Subject: Re: [Sdcc-user] Silabs IDE > > > --- On Mon, 12/24/12, Raphael Neider > <wlmailhtml:/mc/compose?to=rn...@we...> wrote: > > > From: Raphael Neider > <wlmailhtml:/mc/compose?to=rn...@we...> > Subject: Re: [Sdcc-user] cygwin?? > To: sdc...@li... > Date: Monday, December 24, 2012, 8:11 PM > > > Hi iTronix, > > sdcpp.exe: fatal error: when writing output to : No > error > at 1: warning 119: don't know what to do with file 'DB'. > file extension unsupported > at 1: warning 119: don't know what to do with file 'OE'. > file extension unsupported > at 1: warning 119: don't know what to do with file > 'QUIET'. file extension unsupported > at 1: warning 119: don't know what to do with file > 'INTXD'. file extension unsupported > at 1: warning 119: don't know what to do with file > 'OT(6,Speed)'. file extension unsupported > at 1: warning 119: don't know what to do with file > 'PIN(C:\SiLabs\MCU\Inc;C:\Program'. file extension > unsupported > at 1: warning 119: don't know what to do with file > 'Files'. file extension unsupported > at 1: warning 119: don't know what to do with file > '(x86)\SDCC\inc;C:\Program'. file extension unsupported > at 1: warning 119: don't know what to do with file > 'Files'. file extension unsupported > at 1: warning 119: don't know what to do with file > '(x86)\SDCC\inc\51)'. file extension unsupported > > This looks weird -- symbols from the C source / .asm > output interpreted as filenames? Might be due to some > problems with pipes between preprocessor, compiler, > assembler, and linker in cygwin. If I remember correctly, > this at one time was indeed a problem -- unfortunately I > do not remember the solution (or workaround). You might > try searching the mailing list archive or the web for > "pipe cygwin" and your Windows version (XP?). > > Could you post Windows version, exact command line, > command line and output with -V (capital Vee) added? If > you pass complete filenames, you might need to quote them > ("Program Files (x86)" is otherwise treated as three files > ...). > Sorry, I have no clue as to how to do this with Silabs > IDE. Could you run sdcc from the command line / cygwin > shell directly and report the results? > > c8051f300.h:15: syntax error: token -> 'P0' ; column 6 > Link in progress... > C:\Program Files (x86)\SDCC\bin\sdcc.exe > @"C:\Users\Don\Documents\iTech\DTMF Project\DTMF SDCC > Code\generator\cyglink.txt" > > at 1: warning 119: don't know what to do with file > '@C:\Users\Don\Documents\iTech\DTMF Project\DTMF SDCC > Code\generator\cyglink.txt'. file extension unsupported > > The leading "@" confuses me. Maybe the above hints help to > sort this out as well ... What's the contents of > cyglink.txt? Is this file generated by the IDE or > hand-written? > > Kind regards and Merry Christmas, > Raphael > > ====================== Hello, > > (Note, this question probably should have been directed to > the Silabs forums.) > > This is the first time I've heard of people using Silicon > Labs IDE with sdcc, so I downloaded and installed the > Silabs IDE program, in Win XP. The default toolchain > settings calls Ride, using these commands: > > DB OE QUIET INTXD OT(6,Speed) > PIN(C:\SiLabs\MCU\Inc;C:\RIDE\inc;C:\RIDE\inc\51) > > sdcpp doesn't know what to do with these commands, since > they are targeted for rc51. > > In Silabs IDE, click on Project, Tool Chain Integration, > then select the drop box down arrow under Tool Definition > Presets, and select SDCC 3.xx. Then browse to find where > SDCC is installed. > > Hope this helps! > > Rich. > > -----Inline Attachment Follows----- > > > _______________________________________________ > Sdcc-user mailing list > Sdc...@li... > https://lists.sourceforge.net/lists/listinfo/sdcc-user > > > > ------------------------------------------------------------------------ > ------------------------------------------------------------------------------ > Master HTML5, CSS3, ASP.NET, MVC, AJAX, Knockout.js, Web API and > much more. Get web development skills now with LearnDevNow - > 350+ hours of step-by-step video tutorials by Microsoft MVPs and > experts. > SALE $99.99 this month only -- learn more at: > http://p.sf.net/sfu/learnmore_122812 > ------------------------------------------------------------------------ > _______________________________________________ > Sdcc-user mailing list > Sdc...@li... > https://lists.sourceforge.net/lists/listinfo/sdcc-user > > > -----Inline Attachment Follows----- > > > ------------------------------------------------------------------------------ > Master HTML5, CSS3, ASP.NET, MVC, AJAX, Knockout.js, Web API and > much more. Get web development skills now with LearnDevNow - > 350+ hours of step-by-step video tutorials by Microsoft MVPs and > experts. > SALE $99.99 this month only -- learn more at: > http://p.sf.net/sfu/learnmore_122812 > > -----Inline Attachment Follows----- > > > _______________________________________________ > Sdcc-user mailing list > wlmailhtml:/mc/compose?to=Sdc...@li... > https://lists.sourceforge.net/lists/listinfo/sdcc-user > > > > > -------------------------------------------------------------------------------- > ------------------------------------------------------------------------------ > Master HTML5, CSS3, ASP.NET, MVC, AJAX, Knockout.js, Web API and > much more. Get web development skills now with LearnDevNow - > 350+ hours of step-by-step video tutorials by Microsoft MVPs and experts. > SALE $99.99 this month only -- learn more at: > http://p.sf.net/sfu/learnmore_122812 > > > -------------------------------------------------------------------------------- > _______________________________________________ > Sdcc-user mailing list > Sdc...@li... > https://lists.sourceforge.net/lists/listinfo/sdcc-user > ------------------------------------------------------------------------------ > Master Visual Studio, SharePoint, SQL, ASP.NET, C# 2012, HTML5, CSS, > MVC, Windows 8 Apps, JavaScript and much more. Keep your skills current > with LearnDevNow - 3,200 step-by-step video tutorials by Microsoft > MVPs and experts. SALE $99.99 this month only -- learn more at: > http://p.sf.net/sfu/learnmore_122912_______________________________________________ > Sdcc-user mailing list > Sdc...@li... > https://lists.sourceforge.net/lists/listinfo/sdcc-user > |