Menu
▾
▴
Re: [smartmontools-support]pre-fail/old age and smart database
|
From: Bruce A. <ba...@gr...> - 2003-10-10 05:55:00
|
Micah, Please read the man page: 'man smartctl' carefully. Pre-fail and Old_age do not describe the state of the Attributes, they describe the type of the Attributes. Phil, could you please add this to knowndrive.c? It doesn't need any -v settings. A few minutes of research will probably give a set of equivalent drives of different capacity so 040 will have some other variants? Cheers, Bruce On Thu, 9 Oct 2003, micah wrote: > Hello, > > I've got a drive that I suspect (it was causing problems before, but > isn't now), a lot of the attributes show the drive in "Pre-fail" or > "Old_age" state, when I know that this drive is not an old drive at > all. Could this be because the device is not in the smartctl database? > And if so, how can I get it in there? Here is a dump of smartctl -a > (where you can see the various errors that occured also)... thanks! > > micah > > > smartctl version 5.1-18 Copyright (C) 2002-3 Bruce Allen > Home page is http://smartmontools.sourceforge.net/ > > === START OF INFORMATION SECTION === > Device Model: IC35L040AVVN07-0 > Serial Number: VNP210B2G66E5B > Firmware Version: VA2OAE0X > Device is: Not in smartctl database [for details use: -P showall] > ATA Version is: 5 > ATA Standard is: ATA/ATAPI-5 T13 1321D revision 1 > Local Time is: Thu Oct 9 14:52:42 2003 PDT > SMART support is: Available - device has SMART capability. > SMART support is: Enabled > > === START OF READ SMART DATA SECTION === > SMART overall-health self-assessment test result: PASSED > > General SMART Values: > Off-line data collection status: (0x80) Offline data collection activity was > never started. > Auto Off-line Data Collection: Enabled. > Self-test execution status: ( 0) The previous self-test routine completed > without error or no self-test has ever > been run. > Total time to complete off-line > data collection: (1177) seconds. > Offline data collection > capabilities: (0x1b) SMART execute Offline immediate. > Automatic timer ON/OFF support. > Suspend Offline collection upon new > command. > Offline surface scan supported. > Self-test supported. > No Conveyance Self-test supported. > No Selective Self-test supported. > SMART capabilities: (0x0003) Saves SMART data before entering > power-saving mode. > Supports SMART auto save timer. > Error logging capability: (0x01) Error logging supported. > No General Purpose Logging support. > Short self-test routine > recommended polling time: ( 1) minutes. > Extended self-test routine > recommended polling time: ( 20) minutes. > > SMART Attributes Data Structure revision number: 16 > Vendor Specific SMART Attributes with Thresholds: > ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE > 1 Raw_Read_Error_Rate 0x000b 080 080 060 Pre-fail Always - 24576341 > 2 Throughput_Performance 0x0005 140 140 050 Pre-fail Offline - 301 > 3 Spin_Up_Time 0x0007 116 116 024 Pre-fail Always - 148 (Average 136) > 4 Start_Stop_Count 0x0012 100 100 000 Old_age Always - 138 > 5 Reallocated_Sector_Ct 0x0033 100 100 005 Pre-fail Always - 0 > 7 Seek_Error_Rate 0x000b 100 100 067 Pre-fail Always - 0 > 8 Seek_Time_Performance 0x0005 142 142 020 Pre-fail Offline - 28 > 9 Power_On_Hours 0x0012 099 099 000 Old_age Always - 9495 > 10 Spin_Retry_Count 0x0013 100 100 060 Pre-fail Always - 0 > 12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 91 > 192 Power-Off_Retract_Count 0x0032 100 100 050 Old_age Always - 526 > 193 Load_Cycle_Count 0x0012 100 100 050 Old_age Always - 526 > 194 Temperature_Celsius 0x0002 171 171 000 Old_age Always - 32 (Lifetime Min/Max 13/71) > 196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 0 > 197 Current_Pending_Sector 0x0022 100 100 000 Old_age Always - 0 > 198 Offline_Uncorrectable 0x0008 100 100 000 Old_age Offline - 0 > 199 UDMA_CRC_Error_Count 0x000a 200 200 000 Old_age Always - 5 > > SMART Error Log Version: 1 > ATA Error Count: 4 > CR = Command Register [HEX] > FR = Features Register [HEX] > SC = Sector Count Register [HEX] > SN = Sector Number Register [HEX] > CL = Cylinder Low Register [HEX] > CH = Cylinder High Register [HEX] > DH = Device/Head Register [HEX] > DC = Device Command Register [HEX] > ER = Error register [HEX] > ST = Status register [HEX] > Timestamp = decimal seconds since the previous disk power-on. > Note: timestamp "wraps" after 2^32 msec = 49.710 days. > > Error 4 occurred at disk power-on lifetime: 8768 hours > When the command that caused the error occurred, the device was active or idle. > > After command completion occurred, registers were: > ER ST SC SN CL CH DH > -- -- -- -- -- -- -- > 84 51 00 f6 06 14 e1 > > Commands leading to the command that caused the error were: > CR FR SC SN CL CH DH DC Timestamp Command/Feature_Name > -- -- -- -- -- -- -- -- --------- -------------------- > c8 00 08 ef 06 14 e1 00 3222169.000 READ DMA > c8 00 08 ef 06 14 e1 00 3222168.900 READ DMA > 10 00 3f 00 00 00 e0 00 3222168.900 RECALIBRATE [OBS-4] > c8 00 08 ef 06 14 e1 00 3222168.900 READ DMA > c8 00 08 ef 06 14 e1 00 3222168.900 READ DMA > > Error 3 occurred at disk power-on lifetime: 8768 hours > When the command that caused the error occurred, the device was active or idle. > > After command completion occurred, registers were: > ER ST SC SN CL CH DH > -- -- -- -- -- -- -- > 84 51 00 f6 06 14 e1 > > Commands leading to the command that caused the error were: > CR FR SC SN CL CH DH DC Timestamp Command/Feature_Name > -- -- -- -- -- -- -- -- --------- -------------------- > c8 00 08 ef 06 14 e1 00 3222168.900 READ DMA > 10 00 3f 00 00 00 e0 00 3222168.900 RECALIBRATE [OBS-4] > c8 00 08 ef 06 14 e1 00 3222168.900 READ DMA > c8 00 08 ef 06 14 e1 00 3222168.900 READ DMA > c8 00 08 57 2a 50 e2 00 3222168.900 READ DMA > > Error 2 occurred at disk power-on lifetime: 8768 hours > When the command that caused the error occurred, the device was active or idle. > > After command completion occurred, registers were: > ER ST SC SN CL CH DH > -- -- -- -- -- -- -- > 84 51 00 f6 06 14 e1 > > Commands leading to the command that caused the error were: > CR FR SC SN CL CH DH DC Timestamp Command/Feature_Name > -- -- -- -- -- -- -- -- --------- -------------------- > c8 00 08 ef 06 14 e1 00 3222168.900 READ DMA > c8 00 08 ef 06 14 e1 00 3222168.900 READ DMA > c8 00 08 57 2a 50 e2 00 3222168.900 READ DMA > b0 d5 01 01 4f c2 e0 00 3220988.500 SMART READ LOG > b0 d5 01 06 4f c2 e0 00 3220988.400 SMART READ LOG > > Error 1 occurred at disk power-on lifetime: 8768 hours > When the command that caused the error occurred, the device was active or idle. > > After command completion occurred, registers were: > ER ST SC SN CL CH DH > -- -- -- -- -- -- -- > 84 51 00 f6 06 14 e1 > > Commands leading to the command that caused the error were: > CR FR SC SN CL CH DH DC Timestamp Command/Feature_Name > -- -- -- -- -- -- -- -- --------- -------------------- > c8 00 08 ef 06 14 e1 00 3222168.900 READ DMA > c8 00 08 57 2a 50 e2 00 3222168.900 READ DMA > b0 d5 01 01 4f c2 e0 00 3220988.500 SMART READ LOG > b0 d5 01 06 4f c2 e0 00 3220988.400 SMART READ LOG > b0 d0 01 00 4f c2 e0 00 3220988.300 SMART READ DATA > > SMART Self-test log structure revision number 1 > Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error > # 1 Extended off-line Completed without error 00% 5263 - > # 2 Short off-line Completed without error 00% 0 - > # 3 Short off-line Completed without error 00% 0 - > > > > ------------------------------------------------------- > This SF.net email is sponsored by: SF.net Giveback Program. > SourceForge.net hosts over 70,000 Open Source Projects. > See the people who have HELPED US provide better services: > Click here: http://sourceforge.net/supporters.php > _______________________________________________ > Smartmontools-support mailing list > Sma...@li... > https://lists.sourceforge.net/lists/listinfo/smartmontools-support > > |