From: upscope <up...@nw...> - 2012-10-11 18:24:46
|
On Thursday, October 11, 2012 11:10:42 AM sundararaj reel wrote: > Hello, > > I have a seagate Barracuda 3TB hard disk. smartctl -a /dev/sda show > very large values for some attributes. For example > Raw_Read_Error_Rate's RAW_VALUE=103138536 ! > > It is a new harddisk. I don't know if the values shown are wrong or > there is some problem with the harddisk. Is there something wrong with > the harddisk ? > > === START OF INFORMATION SECTION === > Device Model: ST3000DM001-9YN166 > Serial Number: XXXXXXX > Firmware Version: CC4B > User Capacity: 3.000.592.982.016 bytes > Device is: Not in smartctl database [for details use: -P showall] Note this device is not in the smartctl database. Therefore i do not think the numbers shown are valid. There is a way to request having the drive added to the database. Try googling as its been sveral years since I had one added and the link I have is bad. Hope this helps. > ATA Version is: 8 > ATA Standard is: ATA-8-ACS revision 4 > > [...snip...] > > SMART Attributes Data Structure revision number: 10 > Vendor Specific SMART Attributes with Thresholds: > ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE > UPDATED WHEN_FAILED RAW_VALUE > 1 Raw_Read_Error_Rate 0x000f 116 100 006 Pre-fail > Always - 103138536 > 3 Spin_Up_Time 0x0003 092 092 000 Pre-fail > Always - 0 > 4 Start_Stop_Count 0x0032 100 100 020 Old_age > Always - 11 > 5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail > Always - 0 > 7 Seek_Error_Rate 0x000f 100 253 030 Pre-fail > Always - 50595 > 9 Power_On_Hours 0x0032 100 100 000 Old_age > Always - 22 > 10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail > Always - 0 > 12 Power_Cycle_Count 0x0032 100 100 020 Old_age > Always - 6 > 183 Unknown_Attribute 0x0032 100 100 000 Old_age > Always - 0 > 184 Unknown_Attribute 0x0032 100 100 099 Old_age > Always - 0 > 187 Reported_Uncorrect 0x0032 100 100 000 Old_age > Always - 0 > 188 Unknown_Attribute 0x0032 100 099 000 Old_age > Always - 4295032833 > 189 High_Fly_Writes 0x003a 100 100 000 Old_age > Always - 0 > 190 Airflow_Temperature_Cel 0x0022 063 056 045 Old_age > Always - 37 (Lifetime Min/Max 24/44) > 191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age > Always - 0 > 192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age > Always - 4 > 193 Load_Cycle_Count 0x0032 100 100 000 Old_age > Always - 11 > 194 Temperature_Celsius 0x0022 037 044 000 Old_age > Always - 37 (0 22 0 0) > 197 Current_Pending_Sector 0x0012 100 100 000 Old_age > Always - 0 > 198 Offline_Uncorrectable 0x0010 100 100 000 Old_age > Offline - 0 > 199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age > Always - 0 > 240 Head_Flying_Hours 0x0000 100 253 000 Old_age > Offline - 198573517963283 > 241 Unknown_Attribute 0x0000 100 253 000 Old_age > Offline - 75760719370 > 242 Unknown_Attribute 0x0000 100 253 000 Old_age > Offline - 128938962395 > > SMART Error Log Version: 1 > No Errors Logged > > SMART Self-test log structure revision number 1 > Num Test_Description Status Remaining > LifeTime(hours) LBA_of_first_error > # 1 Conveyance offline Completed without error 00% 22 > - # 2 Extended offline Completed without error 00% 10 > - # 3 Short offline Completed without error 00% 5 > - > > SMART Selective self-test log data structure revision number 1 > SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS > 1 0 0 Not_testing > 2 0 0 Not_testing > 3 0 0 Not_testing > 4 0 0 Not_testing > 5 0 0 Not_testing > Selective self-test flags (0x0): > After scanning selected spans, do NOT read-scan remainder of disk. > If Selective self-test is pending on power-up, resume after 0 minute delay. -- openSUSE 12.2(Linux 3.4.6-2.10-desktop x86_64)| KDE 4.9.2 "release 511"|Intel core2duo 2.5 MHZ,|8GB DDR3|GeForce 8400GS(NVIDIA-Linux-x86_64-304.51) |