[openocd:tickets] Re: #342 invalid command name "hla_layout"

[Paul F. <da...@us...>]

On Thu, Mar 17, 2022 at 03:43:46PM -0000, Andrew Eidsness wrote:
> I think that the stellaris configuration is for the on-board ICDI which is
> accessible over the board's serial port. I'm experimenting with using an
> external one. There are alot of good examples in that folder though. I might
> start with the stellaris one, then see what else I can do.

All configs in target/ directory are target configs, they do not
include the on-board ICDI or other on-board adapters. Stellaris is the
name of the original line-up, and it should work with your part.

> I don't know much about openocd, I'm mainly just experimenting to see what I can
> get to work.

I suggest you read the official User Manual while doing so.

> Thanks for your help -- this should definitely have been a forum post instead,
> I'll followup there if I have any actual questions.

No idea what forum you have in mind, I suggest using the mailing list
or our IRC channel, I do not read any forums.


---

** [tickets:#342] invalid command name "hla_layout"**

**Status:** new
**Milestone:** 0.11.0
**Created:** Wed Mar 16, 2022 08:53 PM UTC by Andrew Eidsness
**Last Updated:** Thu Mar 17, 2022 03:43 PM UTC
**Owner:** nobody


I've checked out the v0.11.0 branch and built openocd with the config parameters listed at the end.  I've actually tried several different options, the one listed at the end is "everything I could find".

I've also reproduced this on the v0.10.0 that comes bundled with my OS (Ubuntu 20.04).

I've connected a FlySwatter2 to a 1294xl, but I get an error when trying to launch with:

$ openocd -f interface/ftdi/flyswatter2.cfg -f board/ti_ek-tm4c1294xl.cfg -c init
Open On-Chip Debugger 0.11.0-dirty (2022-03-15-11:17)
Licensed under GNU GPL v2
For bug reports, read
	http://openocd.org/doc/doxygen/bugs.html
Warn : Interface already configured, ignoring
/usr/local/bin/../share/openocd/scripts/interface/ti-icdi.cfg:11: Error: invalid command name "hla_layout"
in procedure 'script' 
at file "embedded:startup.tcl", line 26
at file "/usr/local/bin/../share/openocd/scripts/board/ti_ek-tm4c1294xl.cfg", line 7
at file "/usr/local/bin/../share/openocd/scripts/interface/ti-icdi.cfg", line 11

Configuration line:

$ ./configure --enable-dummy --enable-rshim --enable-ftdi --enable-stlink --enable-ti-icdi --enable-ulink --enable-usb-blaster-2 --enable-ft232r --enable-vsllink --enable-xds110 --enable-osbdm --enable-opendous --enable-aice --enable-usbprog --enable-rlink --enable-armjtagew --enable-usb-blaster --enable-presto --enable-openjtag --enable-jlink --enable-jtag_vpi --enable-jtag_dpi --enable-amtjtagaccel --enable-bcm2835gpio --enable-imx_gpio --enable-ep93xx --enable-at91rm9200 --enable-gw16012 --enable-buspirate --enable-sysfsgpio --enable-xlnx-pcie-xvc --enable-remote-bitbang



---

Sent from sourceforge.net because ope...@li... is subscribed to https://sourceforge.net/p/openocd/tickets/

To unsubscribe from further messages, a project admin can change settings at https://sourceforge.net/p/openocd/admin/tickets/options.  Or, if this is a mailing list, you can unsubscribe from the mailing list.