Menu
▾
▴
[OpenOCD-devel] [openocd:tickets] #270 Kinetis MK22FX512: Error writing FCF Block 0X400 - 0x40f
|
From: Tom <to...@us...> - 2020-06-23 06:43:33
|
Looks strange. Please be aware that code base [https://github.com/sysprogs/openocd] is not same as our "official" source, so it might be a problem of sysprog's changes. Let's hope it's not the case. I tested programming with our fresh git master code in almost identical setup: FTDI based SWD resistor hack and MK22FX512, just the blink test is not arduino based - and gues what - programming works: Open On-Chip Debugger 0.10.0+dev-01267-g0b02281-dirty (2020-05-28-18:10) Licensed under GNU GPL v2 For bug reports, read http://openocd.org/doc/doxygen/bugs.html Info : FTDI SWD mode enabled Info : add flash_bank kinetis kx.pflash Info : clock speed 1000 kHz Info : SWD DPIDR 0x2ba01477 Info : kx.cpu: hardware has 6 breakpoints, 4 watchpoints Info : MDM: Chip is unsecured. Continuing. Info : starting gdb server for kx.cpu on 3333 Info : Listening on port 3333 for gdb connections Info : MDM: Chip is unsecured. Continuing. target halted due to debug-request, current mode: Thread xPSR: 0x01000000 pc: 0x000004e8 msp: 0x20010000 Info : Kinetis MK22FX512xxx12 detected: 2 flash blocks Info : 1 PFlash banks: 512k total Info : 1 FlexNVM banks: 128k total, 128k available as data flash, 4096bytes Flex RAM Info : Disabling Kinetis watchdog (initial WDOG_STCTRLH = 0x01d3) Info : WDOG_STCTRLH = 0x01d2 ** Programming Started ** ** Programming Finished ** ** Verify Started ** ** Verified OK ** ** Resetting Target ** Info : MDM: Chip is unsecured. Continuing. Info : Listening on port 6666 for tcl connections Info : Listening on port 4444 for telnet connections Please first check if FCF field is configured properly in your binary ~~~ arm-none-eabi-objdump -h BlinkTestBlue.ino.elf ~~~ should look like: ~~~ Sections: Idx Name Size VMA LMA File off Algn 0 .interrupts 00000400 00000000 00000000 00008000 2**2 CONTENTS, ALLOC, LOAD, READONLY, DATA 1 .flash_config 00000010 00000400 00000400 00008400 2**0 CONTENTS, ALLOC, LOAD, READONLY, DATA 2 .text 00005068 00000410 00000410 00008410 2**2 CONTENTS, ALLOC, LOAD, READONLY, CODE ... ~~~ If not, the check linker ld script. If FCF is ok, then please re-run programming cmd with -d3 and put the result log somewhere --- ** [tickets:#270] Kinetis MK22FX512: Error writing FCF Block 0X400 - 0x40f** **Status:** new **Milestone:** 0.9.0 **Created:** Sun Jun 14, 2020 06:14 AM UTC by Noel Diviney **Last Updated:** Tue Jun 23, 2020 03:18 AM UTC **Owner:** nobody Hi nall, Error at address 0x400 when programming flash on Kinetis MK22F512xxx12 However, when I press the reset buuton after programming the Led Blinks normally. Does the FCF block have to be skipped somehow? Is the "Error: libusb_open() failed with LIBUSB_ERROR_NOT_SUPPORTED" a problem given that the program runs. The terminal output is as follows :- noel@DESKTOP-0AFLL5T MSYS /w/adgp-1611/portable/sketchbook/BlinkTestBlue/build $ openocd -f interface/ftdi/olimex-arm-usb-ocd.cfg -f target/kx.cfg -c "program BlinkTestBlue.ino.elf verify reset" Open On-Chip Debugger 0.10.0 (2020-05-30) [https://github.com/sysprogs/openocd] Licensed under GNU GPL v2 libusb1 09e75e98b4d9ea7909e8837b7a3f00dda4589dc3 For bug reports, read http://openocd.org/doc/doxygen/bugs.html Info : auto-selecting first available session transport "jtag". To override use 'transport select <transport>'. Info : add flash_bank kinetis kx.pflash Error: libusb_open() failed with LIBUSB_ERROR_NOT_SUPPORTED Info : clock speed 1000 kHz Info : JTAG tap: kx.cpu tap/device found: 0x4ba00477 (mfg: 0x23b (ARM Ltd.), part: 0xba00, ver: 0x4) Info : kx.cpu: hardware has 6 breakpoints, 4 watchpoints Info : kx.cpu: external reset detected Info : MDM: Chip is unsecured. Continuing. Info : starting gdb server for kx.cpu on 3333 Info : Listening on port 3333 for gdb connections Info : JTAG tap: kx.cpu tap/device found: 0x4ba00477 (mfg: 0x23b (ARM Ltd.), part: 0xba00, ver: 0x4) Info : MDM: Chip is unsecured. Continuing. target halted due to debug-request, current mode: Thread xPSR: 0x01000000 pc: 0x00000188 msp: 0x20010000 Info : Kinetis MK22FX512xxx12 detected: 2 flash blocks Info : 1 PFlash banks: 512k total Info : 1 FlexNVM banks: 128k total, 128k available as data flash, 4096bytes FlexRAM Info : Disabling Kinetis watchdog (initial WDOG_STCTRLH = 0x01d3) Info : WDOG_STCTRLH = 0x01d2 ** Programming Started ** Error: Flash write error at 0x00000400 ** Programming Finished ** ** Verify Started ** Error: timed out while waiting for target halted Error: error executing cortex_m crc algorithm Error: JTAG-DP STICKY ERROR Error: Failed to read memory at 0x00000404 embedded:startup.tcl:500: Error: ** Verify Failed ** in procedure 'program' in procedure 'program_error' called at file "embedded:startup.tcl", line 561 at file "embedded:startup.tcl", line 500 noel@DESKTOP-0AFLL5T MSYS /w/adgp-1611/portable/sketchbook/BlinkTestBlue/build $ openocd -f interface/ftdi/olimex-arm-usb-ocd.cfg -f interface/ftdi/swd-resistor-hack.cfg -c "transport select swd" -f target/kx.cfg -c "program BlinkTestBlue.ino.elf verify reset" Open On-Chip Debugger 0.10.0 (2020-05-30) [https://github.com/sysprogs/openocd] Licensed under GNU GPL v2 libusb1 09e75e98b4d9ea7909e8837b7a3f00dda4589dc3 For bug reports, read http://openocd.org/doc/doxygen/bugs.html Info : FTDI SWD mode enabled Warn : Transport "swd" was already selected swd Info : add flash_bank kinetis kx.pflash Error: libusb_open() failed with LIBUSB_ERROR_NOT_SUPPORTED Info : clock speed 1000 kHz Info : SWD DPIDR 0x2ba01477 Info : kx.cpu: hardware has 6 breakpoints, 4 watchpoints Info : kx.cpu: external reset detected Info : MDM: Chip is unsecured. Continuing. Info : starting gdb server for kx.cpu on 3333 Info : Listening on port 3333 for gdb connections Info : MDM: Chip is unsecured. Continuing. target halted due to debug-request, current mode: Thread xPSR: 0x01000000 pc: 0x00000188 msp: 0x20010000 Info : Kinetis MK22FX512xxx12 detected: 2 flash blocks Info : 1 PFlash banks: 512k total Info : 1 FlexNVM banks: 128k total, 128k available as data flash, 4096bytes FlexRAM Info : Disabling Kinetis watchdog (initial WDOG_STCTRLH = 0x01d3) Info : WDOG_STCTRLH = 0x01d2 ** Programming Started ** Error: Flash write error at 0x00000400 ** Programming Finished ** ** Verify Started ** Error: timed out while waiting for target halted Error: error executing cortex_m crc algorithm Info : SWD DPIDR 0x2ba01477 Error: Failed to read memory at 0x00000404 embedded:startup.tcl:500: Error: ** Verify Failed ** in procedure 'program' in procedure 'program_error' called at file "embedded:startup.tcl", line 561 at file "embedded:startup.tcl", line 500 noel@DESKTOP-0AFLL5T MSYS /w/adgp-1611/portable/sketchbook/BlinkTestBlue/build $ I am having difficulty understanding how to manage the FCF flash block. Any help would be much appreciated. Many Thanks Noel Diviney --- Sent from sourceforge.net because ope...@li... is subscribed to https://sourceforge.net/p/openocd/tickets/ To unsubscribe from further messages, a project admin can change settings at https://sourceforge.net/p/openocd/admin/tickets/options. Or, if this is a mailing list, you can unsubscribe from the mailing list. |
