Re: [Openbts-discuss] First installation problems

[Balthasar I. <ba...@in...>]

I also reset the MCC and MNC codes to 001/01, which makes the iPhone see
the network as Test PLMN 1-1

Do I need to change the colour code?

Still no luck and getting this false SOS Only indication when connected
with no welcome or rejection SMS being sent. Trying to send an SMS to 411
results in a send error.

On Saturday, 23 January 2016, Balthasar Indermuehle <ba...@in...> wrote:

> Yes, I even rebooted the computer.
>
> On Saturday, 23 January 2016, at ion Pandeya <nee...@et...
> <javascript:_e(%7B%7D,'cvml','nee...@et...');>> wrote:
>
>> After enabling open registration, you need to re-start OpenBTS. Did you
>> already do this?
>>
>>
>>
>> On 22 January 2016 at 03:40, Balthasar Indermuehle <ba...@in...>
>> wrote:
>>
>>> Yes I think so. Am I missing anything?
>>>
>>> OpenBTS> config Control.LUR.Open
>>> Control.LUR.OpenRegistration .*
>>> Control.LUR.OpenRegistration.Message You're in a radio quiet zone. Turn
>>> off
>>> Control.LUR.OpenRegistration.Reject (disabled)     [default]
>>> Control.LUR.OpenRegistration.ShortCode 101     [default]
>>>
>>>
>>>
>>> On 22 January 2016 at 20:55, Ralph A. Schmid, dk5ras <ra...@sc...>
>>> wrote:
>>> > Did you enable
>>> ​​
>>> open registration, to allow all phones logging on without
>>> > first manually registering their IMSI?
>>> >
>>> > Ralph.
>>> >
>>> >> -----Original Message-----
>>> >> From: Balthasar Indermuehle [mailto:ba...@in...]
>>> >> Sent: Friday, January 22, 2016 7:51 AM
>>> >> To: Tom Tsou
>>> >> Cc: OpenBTS Discuss
>>> >> Subject: Re: [Openbts-discuss] First installation problems
>>> >>
>>> >> Back at the office now, and it seems to transmit the cell information
>>> just
>>> > fine.
>>> >> I can see and decode the OpenBTS signal with the other B200 running
>>> >> airspy/gsmprobe, it reports the correct MCC/MNC/LAC/CID that I've set
>>> via
>>> >> the OpenBTSCLI interface.
>>> >>
>>> >> With the iPhone I can see and manually select my network. However,
>>> when I
>>> >> select it, the iPhone 5 displays first No Service for 10-20 seconds,
>>> then
>>> > SOS
>>> >> Only, and stays on SOS Only with my network selected (which would be
>>> OK
>>> >> as the IMSI is not yet registered on that network).
>>> >> Starting the iPhone engineering console never completes (not sure if
>>> > that's
>>> >> by design, i.e. you need to be a subscriber to get the network info,
>>> >> probably).
>>> >>
>>> >> On the OpenBTS side nothing seems to happen at all. stats shows no
>>> count
>>> >> increase on anything other than the OpenBTSCLI commands. The power,
>>> gain
>>> >> and noise all seem to be in OK ranges. Looking at the spectrum I
>>> selected
>>> > it is
>>> >> clean before the access point is started (see spectrum plot here:
>>> >> https://cloud.inside.net/index.php/s/k4zQRGTcGxzrjsk, ARFCN 1 is at
>>> >> 935.2 MHz, left most peak in the plot. At the bottom of the waterfall
>>> you
>>> > can
>>> >> see the clean spectrum before I switched it on, there's nothing else
>>> > there).
>>> >>
>>> >> OpenBTS> power
>>> >> current downlink power -20 dB wrt full scale
>>> >>
>>> >> OpenBTS> rxgain
>>> >> current RX gain is 10 dB
>>> >>
>>> >> OpenBTS> noise
>>> >> noise RSSI is -79 dB wrt full scale
>>> >> MS RSSI target is -50 dB wrt full scale
>>> >> INFO: the current noise level is acceptable.
>>> >>
>>> >> tmsis displays nothing. About once every 30 odd seconds, this log
>>> entry is
>>> >> made in syslog:
>>> >> Jan 22 17:34:49 x transceiver: NOTICE 8449:9083 2016-01-22T17:34:49.7
>>> >> Transceiver.cpp:192:pushRadioVector: dumping STALE burst in TRX->USRP
>>> >> interface
>>> >>
>>> >> Not sure if that says anything.
>>> >>
>>> >> What else can I check?
>>> >>
>>> >>
>>> >> On 22 January 2016 at 12:41, Balthasar Indermuehle <ba...@in...>
>>> >> wrote:
>>> >> > Many thanks for your help Tom! I think the patch did the trick.
>>> >> >
>>> >> > I can now run the OpenBTSCLI and set up the network, I can see the
>>> >> > B200 putting out power at the right frequencies (benefits of having
>>> >> > two I guess!).
>>> >> >
>>> >> > On 22 January 2016 at 11:17, Tom Tsou <tom...@et...> wrote:
>>> >> >> On Thu, Jan 21, 2016 at 4:01 PM, Balthasar Indermuehle
>>> >> <ba...@in...> wrote:
>>> >> >>> Jan 22 10:56:33 x openbts: EMERG 3594:3603 2016-01-22T10:56:33.5
>>> >> >>> OpenBTS.cpp:185:startTransceiver: Transceiver quit with status
>>> 32512.
>>> >> >>> Exiting.
>>> >> >>
>>> >> >> There is no way to pass device arguments into OpenBTS to pass down
>>> to
>>> >> >> transceiver.
>>> >> >>
>>> >> >> I would disable the OpenBTS transceiver start and run the
>>> transceiver
>>> >> >> manually from the command line with the device arguments.
>>> >> >>
>>> >> >>   -TT
>>> >>
>>> >>
>>> >
>>> ----------------------------------------------------------------------------
>>> > --
>>> >> Site24x7 APM Insight: Get Deep Visibility into Application
>>> Performance APM
>>> >> + Mobile APM + RUM: Monitor 3 App instances at just $35/Month Monitor
>>> >> end-to-end web transactions and take corrective actions now
>>> Troubleshoot
>>> >> faster and improve end-user experience. Signup Now!
>>> >> http://pubads.g.doubleclick.net/gampad/clk?id=267308311&iu=/4140
>>> >> _______________________________________________
>>> >> Openbts-discuss mailing list
>>> >> Ope...@li...
>>> >> https://lists.sourceforge.net/lists/listinfo/openbts-discuss
>>> >
>>>
>>>
>>> ------------------------------------------------------------------------------
>>> Site24x7 APM Insight: Get Deep Visibility into Application Performance
>>> APM + Mobile APM + RUM: Monitor 3 App instances at just $35/Month
>>> Monitor end-to-end web transactions and take corrective actions now
>>> Troubleshoot faster and improve end-user experience. Signup Now!
>>> http://pubads.g.doubleclick.net/gampad/clk?id=267308311&iu=/4140
>>> _______________________________________________
>>> Openbts-discuss mailing list
>>> Ope...@li...
>>> https://lists.sourceforge.net/lists/listinfo/openbts-discuss
>>>
>>
>>