Re: [Openbts-discuss] First installation problems

[Neel P. <nee...@et...>]

After enabling open registration, you need to re-start OpenBTS. Did you
already do this?



On 22 January 2016 at 03:40, Balthasar Indermuehle <ba...@in...> wrote:

> Yes I think so. Am I missing anything?
>
> OpenBTS> config Control.LUR.Open
> Control.LUR.OpenRegistration .*
> Control.LUR.OpenRegistration.Message You're in a radio quiet zone. Turn off
> Control.LUR.OpenRegistration.Reject (disabled)     [default]
> Control.LUR.OpenRegistration.ShortCode 101     [default]
>
>
>
> On 22 January 2016 at 20:55, Ralph A. Schmid, dk5ras <ra...@sc...>
> wrote:
> > Did you enable
> ​​
> open registration, to allow all phones logging on without
> > first manually registering their IMSI?
> >
> > Ralph.
> >
> >> -----Original Message-----
> >> From: Balthasar Indermuehle [mailto:ba...@in...]
> >> Sent: Friday, January 22, 2016 7:51 AM
> >> To: Tom Tsou
> >> Cc: OpenBTS Discuss
> >> Subject: Re: [Openbts-discuss] First installation problems
> >>
> >> Back at the office now, and it seems to transmit the cell information
> just
> > fine.
> >> I can see and decode the OpenBTS signal with the other B200 running
> >> airspy/gsmprobe, it reports the correct MCC/MNC/LAC/CID that I've set
> via
> >> the OpenBTSCLI interface.
> >>
> >> With the iPhone I can see and manually select my network. However, when
> I
> >> select it, the iPhone 5 displays first No Service for 10-20 seconds,
> then
> > SOS
> >> Only, and stays on SOS Only with my network selected (which would be OK
> >> as the IMSI is not yet registered on that network).
> >> Starting the iPhone engineering console never completes (not sure if
> > that's
> >> by design, i.e. you need to be a subscriber to get the network info,
> >> probably).
> >>
> >> On the OpenBTS side nothing seems to happen at all. stats shows no count
> >> increase on anything other than the OpenBTSCLI commands. The power, gain
> >> and noise all seem to be in OK ranges. Looking at the spectrum I
> selected
> > it is
> >> clean before the access point is started (see spectrum plot here:
> >> https://cloud.inside.net/index.php/s/k4zQRGTcGxzrjsk, ARFCN 1 is at
> >> 935.2 MHz, left most peak in the plot. At the bottom of the waterfall
> you
> > can
> >> see the clean spectrum before I switched it on, there's nothing else
> > there).
> >>
> >> OpenBTS> power
> >> current downlink power -20 dB wrt full scale
> >>
> >> OpenBTS> rxgain
> >> current RX gain is 10 dB
> >>
> >> OpenBTS> noise
> >> noise RSSI is -79 dB wrt full scale
> >> MS RSSI target is -50 dB wrt full scale
> >> INFO: the current noise level is acceptable.
> >>
> >> tmsis displays nothing. About once every 30 odd seconds, this log entry
> is
> >> made in syslog:
> >> Jan 22 17:34:49 x transceiver: NOTICE 8449:9083 2016-01-22T17:34:49.7
> >> Transceiver.cpp:192:pushRadioVector: dumping STALE burst in TRX->USRP
> >> interface
> >>
> >> Not sure if that says anything.
> >>
> >> What else can I check?
> >>
> >>
> >> On 22 January 2016 at 12:41, Balthasar Indermuehle <ba...@in...>
> >> wrote:
> >> > Many thanks for your help Tom! I think the patch did the trick.
> >> >
> >> > I can now run the OpenBTSCLI and set up the network, I can see the
> >> > B200 putting out power at the right frequencies (benefits of having
> >> > two I guess!).
> >> >
> >> > On 22 January 2016 at 11:17, Tom Tsou <tom...@et...> wrote:
> >> >> On Thu, Jan 21, 2016 at 4:01 PM, Balthasar Indermuehle
> >> <ba...@in...> wrote:
> >> >>> Jan 22 10:56:33 x openbts: EMERG 3594:3603 2016-01-22T10:56:33.5
> >> >>> OpenBTS.cpp:185:startTransceiver: Transceiver quit with status
> 32512.
> >> >>> Exiting.
> >> >>
> >> >> There is no way to pass device arguments into OpenBTS to pass down to
> >> >> transceiver.
> >> >>
> >> >> I would disable the OpenBTS transceiver start and run the transceiver
> >> >> manually from the command line with the device arguments.
> >> >>
> >> >>   -TT
> >>
> >>
> >
> ----------------------------------------------------------------------------
> > --
> >> Site24x7 APM Insight: Get Deep Visibility into Application Performance
> APM
> >> + Mobile APM + RUM: Monitor 3 App instances at just $35/Month Monitor
> >> end-to-end web transactions and take corrective actions now Troubleshoot
> >> faster and improve end-user experience. Signup Now!
> >> http://pubads.g.doubleclick.net/gampad/clk?id=267308311&iu=/4140
> >> _______________________________________________
> >> Openbts-discuss mailing list
> >> Ope...@li...
> >> https://lists.sourceforge.net/lists/listinfo/openbts-discuss
> >
>
>
> ------------------------------------------------------------------------------
> Site24x7 APM Insight: Get Deep Visibility into Application Performance
> APM + Mobile APM + RUM: Monitor 3 App instances at just $35/Month
> Monitor end-to-end web transactions and take corrective actions now
> Troubleshoot faster and improve end-user experience. Signup Now!
> http://pubads.g.doubleclick.net/gampad/clk?id=267308311&iu=/4140
> _______________________________________________
> Openbts-discuss mailing list
> Ope...@li...
> https://lists.sourceforge.net/lists/listinfo/openbts-discuss
>