Re: [Openbts-discuss] First installation problems

[Balthasar I. <ba...@in...>]

Yes I think so. Am I missing anything?

OpenBTS> config Control.LUR.Open
Control.LUR.OpenRegistration .*
Control.LUR.OpenRegistration.Message You're in a radio quiet zone. Turn off
Control.LUR.OpenRegistration.Reject (disabled)     [default]
Control.LUR.OpenRegistration.ShortCode 101     [default]



On 22 January 2016 at 20:55, Ralph A. Schmid, dk5ras <ra...@sc...> wrote:
> Did you enable open registration, to allow all phones logging on without
> first manually registering their IMSI?
>
> Ralph.
>
>> -----Original Message-----
>> From: Balthasar Indermuehle [mailto:ba...@in...]
>> Sent: Friday, January 22, 2016 7:51 AM
>> To: Tom Tsou
>> Cc: OpenBTS Discuss
>> Subject: Re: [Openbts-discuss] First installation problems
>>
>> Back at the office now, and it seems to transmit the cell information just
> fine.
>> I can see and decode the OpenBTS signal with the other B200 running
>> airspy/gsmprobe, it reports the correct MCC/MNC/LAC/CID that I've set via
>> the OpenBTSCLI interface.
>>
>> With the iPhone I can see and manually select my network. However, when I
>> select it, the iPhone 5 displays first No Service for 10-20 seconds, then
> SOS
>> Only, and stays on SOS Only with my network selected (which would be OK
>> as the IMSI is not yet registered on that network).
>> Starting the iPhone engineering console never completes (not sure if
> that's
>> by design, i.e. you need to be a subscriber to get the network info,
>> probably).
>>
>> On the OpenBTS side nothing seems to happen at all. stats shows no count
>> increase on anything other than the OpenBTSCLI commands. The power, gain
>> and noise all seem to be in OK ranges. Looking at the spectrum I selected
> it is
>> clean before the access point is started (see spectrum plot here:
>> https://cloud.inside.net/index.php/s/k4zQRGTcGxzrjsk, ARFCN 1 is at
>> 935.2 MHz, left most peak in the plot. At the bottom of the waterfall you
> can
>> see the clean spectrum before I switched it on, there's nothing else
> there).
>>
>> OpenBTS> power
>> current downlink power -20 dB wrt full scale
>>
>> OpenBTS> rxgain
>> current RX gain is 10 dB
>>
>> OpenBTS> noise
>> noise RSSI is -79 dB wrt full scale
>> MS RSSI target is -50 dB wrt full scale
>> INFO: the current noise level is acceptable.
>>
>> tmsis displays nothing. About once every 30 odd seconds, this log entry is
>> made in syslog:
>> Jan 22 17:34:49 x transceiver: NOTICE 8449:9083 2016-01-22T17:34:49.7
>> Transceiver.cpp:192:pushRadioVector: dumping STALE burst in TRX->USRP
>> interface
>>
>> Not sure if that says anything.
>>
>> What else can I check?
>>
>>
>> On 22 January 2016 at 12:41, Balthasar Indermuehle <ba...@in...>
>> wrote:
>> > Many thanks for your help Tom! I think the patch did the trick.
>> >
>> > I can now run the OpenBTSCLI and set up the network, I can see the
>> > B200 putting out power at the right frequencies (benefits of having
>> > two I guess!).
>> >
>> > On 22 January 2016 at 11:17, Tom Tsou <tom...@et...> wrote:
>> >> On Thu, Jan 21, 2016 at 4:01 PM, Balthasar Indermuehle
>> <ba...@in...> wrote:
>> >>> Jan 22 10:56:33 x openbts: EMERG 3594:3603 2016-01-22T10:56:33.5
>> >>> OpenBTS.cpp:185:startTransceiver: Transceiver quit with status 32512.
>> >>> Exiting.
>> >>
>> >> There is no way to pass device arguments into OpenBTS to pass down to
>> >> transceiver.
>> >>
>> >> I would disable the OpenBTS transceiver start and run the transceiver
>> >> manually from the command line with the device arguments.
>> >>
>> >>   -TT
>>
>>
> ----------------------------------------------------------------------------
> --
>> Site24x7 APM Insight: Get Deep Visibility into Application Performance APM
>> + Mobile APM + RUM: Monitor 3 App instances at just $35/Month Monitor
>> end-to-end web transactions and take corrective actions now Troubleshoot
>> faster and improve end-user experience. Signup Now!
>> http://pubads.g.doubleclick.net/gampad/clk?id=267308311&iu=/4140
>> _______________________________________________
>> Openbts-discuss mailing list
>> Ope...@li...
>> https://lists.sourceforge.net/lists/listinfo/openbts-discuss
>