From: Arghyadip P. <arg...@gm...> - 2011-10-28 23:32:10
|
Dear Thomas and Kurtis, I have downloaded the code from the git branch specified by you. But I am getting build error. I am using 10.04 ubuntu lucid. UHDDevice.cpp:25:33: error: uhd/property_tree.hpp: No such file or directory UHDDevice.cpp:28:29: error: uhd/utils/msg.hpp: No such file or directory UHDDevice.cpp:250: error: variable or field ‘uhd_msg_handler’ declared void UHDDevice.cpp:250: error: ‘uhd::msg’ has not been declared UHDDevice.cpp:250: error: expected primary-expression before ‘const’ make[2]: *** [UHDDevice.lo] Error 1 make[2]: Leaving directory `/home/administrator/Arghyadip/github/ttsou-openbts-p2.8-75d43a9/Transceiver52M' make[1]: *** [all-recursive] Error 1 make[1]: Leaving directory `/home/administrator/Arghyadip/github/ttsou-openbts-p2.8-75d43a9' This is while trying to make the OpenBTS code. I can also see the some OpenBTS UHD code in /github.com/ttsou/openbts-uhd. Shall I try with this with the USRP2 Tx I have Thanks and Regards, Arghyadip On Fri, Oct 28, 2011 at 12:10 AM, Thomas Tsou <tt...@vt...> wrote: > On Fri, Oct 28, 2011 at 12:59 AM, Kurtis Heimerl > <khe...@cs...> wrote: > > The 2.8 release is still in a state of flux as the various 2.6 patches > > (including USRP2 support) are reintegrated into the release. Thomas is > > actively working on the UHD branch in particular and may have it > > working. Hopefully he'll commment. Regardless, it may just be a better > > idea to wait with 2.6 for the short term. > > That is indeed the case. Until things start to settle, use this branch > for P2.8 with UHD patches. > > git clone -b ttsou git://github.com/ttsou/openbts-p2.8.git > > Or this one based on version 2.6. > > git clone git://github.com/ttsou/openbts-uhd.git > > In either case, use the following configure options for USRP2. The > full option list is below. > > ./configure --with-resamp [--with-extref] > > Thomas > > ---- Device Configuration Options ---- > > Mandatory options depend on the device type. Parameters in brackets > are optional. > > ---- USRP1 ---- > > ./configure --with-usrp1 [--with-singledb] > > The usrp1 option enables special USRP1 support with timestamps using > the gnuradio driver. GNU Radio is required, but not UHD. The single > daughterboard switch assumes side A. If not specified, the default > configuration is Tx A / Rx B. > > ---- USRP2 / N2xx ---- > > ./configure --with-resamp [--with-extref] > > All non-USRP1 devices use the Ettus UHD driver; GNU Radio is not > required. USRP2 and N2xx devices are not currently configurable at the > GSM symbol rate and thus require resampling to be enabled. An external > 10MHz reference is optional, but recommended. > > ---- B100 / E100 ---- > > ./configure [--with-resamp] [--with-extref] > > The B100 can operate at the recommended 52MHz or 64MHz with the > software resampler enabled. The E100 can configure itself for either > configuration, but will only work with OpenBTS at 52MHz due to > resource constraints. > > > ------------------------------------------------------------------------------ > The demand for IT networking professionals continues to grow, and the > demand for specialized networking skills is growing even more rapidly. > Take a complimentary Learning@Cisco Self-Assessment and learn > about Cisco certifications, training, and career opportunities. > http://p.sf.net/sfu/cisco-dev2dev > _______________________________________________ > Openbts-discuss mailing list > Ope...@li... > https://lists.sourceforge.net/lists/listinfo/openbts-discuss > -- Arghyadip Paul Graduate Student Department of Computer Science University of California Santa Barbara Santa Barbara , CA 93106 USA |