Re: [GLE-general] error when using format "sci 2 10"

[Lukas F. <fli...@gm...>]

Hey Antonio,

Thanks for helping. I am a little bit helpless, since I cannot find the
file in the zip folder, do you mind sharing it with me?

Am Do., 28. Aug. 2025 um 12:26 Uhr schrieb Antonio DiCesare <
ant...@gm...>:

>
> I think the problem is indeed the inittex.ini file. If I remove it, I get
> the same errors. If I put it back in the GLE root everything works fine. I
> just downloaded the portable version of GLE 4.3.7 for Windows and the
> inittex.ini file is not included in the zip file. I copied it from a
> previous version (4.3.4) and everything works fine.
>
>
> Il giorno gio 28 ago 2025 alle ore 11:41 Lukas Flierl <
> fli...@gm...> ha scritto:
>
>> no same error, but here I cannot fix it...
>>
>> Am Do., 28. Aug. 2025 um 11:29 Uhr schrieb Radek Machulka <
>> rad...@gm...>:
>>
>>> So does this mean you only get this error when using QGLE (not direct
>>> gle
>>> running in terminal)?
>>>
>>> I also had some complains about inittext.ini in the past. Usually, I
>>> just copy
>>> it to the gle's root directory and it is fine. I am not using QGLE
>>> though.
>>> Nowadays, I am getting "/usr/lib/libtiff.so.5: no version information
>>> available", did not have a time to look at it yet.
>>>
>>> R.
>>>
>>>
>>> On čtvrtek 28. srpna 2025 10:55:29, středoevropský letní čas Lukas
>>> Flierl
>>> wrote:
>>> > Hi Radek,
>>> >
>>> > Yes you are right (as always) in my MWE I am using a different number
>>> of
>>> > digits, but as mentioned this is not the cause. I am using Version
>>> 4.3.4,
>>> > the issue might be that whenever I open an GLE  file (I am using QGLE)
>>> I
>>> > get this error: "Could not open inittex.ini file ", I just press
>>> > "Reloade file" and everything works fine.
>>> >
>>> > Cheers
>>> > Lukas
>>> >
>>> > Am Do., 28. Aug. 2025 um 10:51 Uhr schrieb Radek Machulka <
>>> >
>>> > rad...@gm...>:
>>> > > No error on my side, however as I realize, I am using rather old
>>> version
>>> > > of
>>> > > GLE (v.4.3.4). What version do you use? If there is some regression,
>>> is
>>> > > should
>>> > > be relatively easy to find.
>>> > >
>>> > > Just for record, you claim to have an issue with "sci 2 10", however
>>> your
>>> > > code
>>> > > snippet  uses "sci 3 10". Tried both, both works (that is probably
>>> what
>>> > > you
>>> > > meant, by number of digits does not matter).
>>> > >
>>> > > Radek
>>> > >
>>> > >
>>> > > On čtvrtek 28. srpna 2025 10:36:34, středoevropský letní čas Lukas
>>> Flierl
>>> > >
>>> > > wrote:
>>> > > > Dear all,
>>> > > >
>>> > > > I am preparing some figures and when using format "sci 2 10" an
>>> error
>>> > > > occurs. the number of digits does not seem to b the issue I also
>>> tried
>>> > >
>>> > > "sci
>>> > >
>>> > > > 4 10". Here is my GLE code:
>>> > > >
>>> > > > size 12.0 12.0
>>> > > >
>>> > > > begin graph
>>> > > > xaxis min 1 max 100
>>> > > > ! does not work
>>> > > > yaxis min -1e-6 max 3e-3 format "sci 3 10"
>>> > > > ! does work
>>> > > > !yaxis min -1e-6 max 3e-3 format "sci 10"
>>> > > > ! error message. Unrecognised control sequence {cdot}
>>> > > > end graph
>>> > > >
>>> > > > Any idea what is causing this?
>>> > > >
>>> > > > Cheers
>>> > > > Lukas_______________________________________________
>>> > >
>>> > > Glx-general mailing list
>>> > > Glx...@li...
>>> > > https://lists.sourceforge.net/lists/listinfo/glx-general
>>> _______________________________________________
>>> Glx-general mailing list
>>> Glx...@li...
>>> https://lists.sourceforge.net/lists/listinfo/glx-general
>>>
>> _______________________________________________
>> Glx-general mailing list
>> Glx...@li...
>> https://lists.sourceforge.net/lists/listinfo/glx-general
>>
> _______________________________________________
> Glx-general mailing list
> Glx...@li...
> https://lists.sourceforge.net/lists/listinfo/glx-general
>