Menu
▾
▴
Re: [E1000-devel] Hardware Unit Hang, followed by Reset adapter on e1000e - 82583V
|
From: Padam J. S. <pad...@in...> - 2013-08-21 08:27:09
|
Hello Todd,
I was able to resolve the issue by recompiling the kernel with the following completely turned off (and all sub-options also off):
[ ] Power Management support │ │
│ │ [ ] SFI (Simple Firmware Interface) Support ---> │ │
│ │ CPU Frequency scaling ---> │ │
│ │ [ ] CPU idle PM support │ │
│ │ Memory power savings --->
Last 24 hours I have not seen any of the interface reset even once ( I can finally get some sleep :-) )
The appliance is a Core-i5-2400 CPU, with a custom board and 6 X 82583V. Dmesg of the appliance with 2.6.34 kernel with ACPI compiled in the kernel, but turned off via kernel command line:
-bash-3.1# dmesg
Linux version 2.6.34msc64-32xx (ro...@de...) (gcc version 4.1.2 20080704 (Red Hat 4.1.2-48)) #30 SMP Fri Jan 20 18:21:02 IST 2012
Command line: ro root=/dev/sda2 console=ttyS0,115200n8 console=tty1 ide=nodma pcie_aspm=off loglevel=0 acpi=off
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009b800 (usable)
BIOS-e820: 000000000009b800 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 0000000020000000 (usable)
BIOS-e820: 0000000020000000 - 0000000020200000 (reserved)
BIOS-e820: 0000000020200000 - 0000000040000000 (usable)
BIOS-e820: 0000000040000000 - 0000000040200000 (reserved)
BIOS-e820: 0000000040200000 - 00000000bac7d000 (usable)
BIOS-e820: 00000000bac7d000 - 00000000bacc6000 (ACPI NVS)
BIOS-e820: 00000000bacc6000 - 00000000bacce000 (ACPI data)
BIOS-e820: 00000000bacce000 - 00000000bacf0000 (reserved)
BIOS-e820: 00000000bacf0000 - 00000000bacf2000 (usable)
BIOS-e820: 00000000bacf2000 - 00000000bad03000 (reserved)
BIOS-e820: 00000000bad03000 - 00000000bad10000 (ACPI NVS)
BIOS-e820: 00000000bad10000 - 00000000bad37000 (reserved)
BIOS-e820: 00000000bad37000 - 00000000bad7a000 (ACPI NVS)
BIOS-e820: 00000000bad7a000 - 00000000bb000000 (usable)
BIOS-e820: 00000000bb800000 - 00000000bfa00000 (reserved)
BIOS-e820: 00000000fed1c000 - 00000000fed40000 (reserved)
BIOS-e820: 00000000ff000000 - 0000000100000000 (reserved)
BIOS-e820: 0000000100000000 - 000000013fe00000 (usable)
NX (Execute Disable) protection: active
DMI 2.7 present.
AMI BIOS detected: BIOS may corrupt low RAM, working around it.
e820 update range: 0000000000000000 - 0000000000010000 (usable) ==> (reserved)
e820 update range: 0000000000000000 - 0000000000001000 (usable) ==> (reserved)
e820 remove range: 00000000000a0000 - 0000000000100000 (usable)
No AGP bridge found
last_pfn = 0x13fe00 max_arch_pfn = 0x400000000
MTRR default type: uncachable
MTRR fixed ranges enabled:
00000-9FFFF write-back
A0000-BFFFF uncachable
C0000-CFFFF write-protect
D0000-E7FFF uncachable
E8000-FFFFF write-protect
MTRR variable ranges enabled:
0 base 000000000 mask F00000000 write-back
1 base 100000000 mask FC0000000 write-back
2 base 0BB800000 mask FFF800000 uncachable
3 base 0BC000000 mask FFC000000 uncachable
4 base 0C0000000 mask FC0000000 uncachable
5 base 13FE00000 mask FFFE00000 uncachable
6 disabled
7 disabled
8 disabled
9 disabled
x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
e820 update range: 00000000bb800000 - 0000000100000000 (usable) ==> (reserved)
last_pfn = 0xbb000 max_arch_pfn = 0x400000000
initial memory mapped : 0 - 20000000
found SMP MP-table at [ffff8800000fce60] fce60
init_memory_mapping: 0000000000000000-00000000bb000000
0000000000 - 00bb000000 page 2M
kernel direct mapping tables up to bb000000 @ 12000-16000
init_memory_mapping: 0000000100000000-000000013fe00000
0100000000 - 013fe00000 page 2M
kernel direct mapping tables up to 13fe00000 @ 14000-1a000
No NUMA configuration found
Faking a node at 0000000000000000-000000013fe00000
Initmem setup node 0 0000000000000000-000000013fe00000
NODE_DATA [0000000100000000 - 0000000100004fff]
[ffffea0000000000-ffffea00045fffff] PMD -> [ffff880100200000-ffff8801039fffff] on node 0
Zone PFN ranges:
DMA 0x00000010 -> 0x00001000
DMA32 0x00001000 -> 0x00100000
Normal 0x00100000 -> 0x0013fe00
Movable zone start PFN for each node
early_node_map[7] active PFN ranges
0: 0x00000010 -> 0x0000009b
0: 0x00000100 -> 0x00020000
0: 0x00020200 -> 0x00040000
0: 0x00040200 -> 0x000bac7d
0: 0x000bacf0 -> 0x000bacf2
0: 0x000bad7a -> 0x000bb000
0: 0x00100000 -> 0x0013fe00
On node 0 totalpages: 1026192
DMA zone: 56 pages used for memmap
DMA zone: 0 pages reserved
DMA zone: 3923 pages, LIFO batch:0
DMA32 zone: 14280 pages used for memmap
DMA32 zone: 746301 pages, LIFO batch:31
Normal zone: 3577 pages used for memmap
Normal zone: 258055 pages, LIFO batch:31
Intel MultiProcessor Specification v1.4
MPTABLE: OEM ID: A M I
MPTABLE: Product ID: ALASKA
MPTABLE: APIC at: 0xFEE00000
Processor #0 (Bootup-CPU)
Processor #2
Processor #4
Processor #6
I/O APIC #0 Version 32 at 0xFEC00000.
Processors: 4
SMP: Allowing 4 CPUs, 0 hotplug CPUs
nr_irqs_gsi: 24
early_res array is doubled to 64 at [15000 - 157ff]
Allocating PCI resources starting at bfa00000 (gap: bfa00000:3f31c000)
setup_percpu: NR_CPUS:255 nr_cpumask_bits:255 nr_cpu_ids:4 nr_node_ids:1
PERCPU: Embedded 27 pages/cpu @ffff880001c00000 s80744 r8192 d21656 u524288
pcpu-alloc: s80744 r8192 d21656 u524288 alloc=1*2097152
pcpu-alloc: [0] 0 1 2 3
early_res array is doubled to 128 at [15800 - 167ff]
Built 1 zonelists in Node order, mobility grouping on. Total pages: 1008279
Policy zone: Normal
Kernel command line: ro root=/dev/sda2 console=ttyS0,115200n8 console=tty1 ide=nodma pcie_aspm=off loglevel=0 acpi=off
PID hash table entries: 4096 (order: 3, 32768 bytes)
xsave/xrstor: enabled xstate_bv 0x7, cntxt size 0x340
Checking aperture...
No AGP bridge found
Subtract (63 early reservations)
#1 [0001000000 - 0001baa690] TEXT DATA BSS
#2 [0001bab000 - 0001bab2a2] BRK
#3 [00000fce70 - 0000100000] BIOS reserved
#4 [00000fce60 - 00000fce70] MP-table mpf
#5 [000009b800 - 00000fcb40] BIOS reserved
#6 [00000fcddc - 00000fce60] BIOS reserved
#7 [00000fcb40 - 00000fcddc] MP-table mpc
#8 [0000010000 - 0000012000] TRAMPOLINE
#9 [0000012000 - 0000014000] PGTABLE
#10 [0000014000 - 0000015000] PGTABLE
#11 [0100000000 - 0100005000] NODE_DATA
#12 [0001bab2c0 - 0001bac2c0] BOOTMEM
#13 [0001baa6c0 - 0001baa8c0] BOOTMEM
#14 [0100005000 - 0100006000] BOOTMEM
#15 [0100006000 - 0100007000] BOOTMEM
#16 [0100200000 - 0103a00000] MEMMAP 0
#17 [0001baa8c0 - 0001baaa40] BOOTMEM
#18 [0001bac2c0 - 0001bc42c0] BOOTMEM
#19 [0001bc42c0 - 0001bca2c0] BOOTMEM
#20 [0001bcb000 - 0001bcc000] BOOTMEM
#21 [0001baaa40 - 0001baaa83] BOOTMEM
#22 [0001baaac0 - 0001baaf90] BOOTMEM
#23 [0001bca2c0 - 0001bca328] BOOTMEM
#24 [0001bca340 - 0001bca3a8] BOOTMEM
#25 [0001bca3c0 - 0001bca428] BOOTMEM
#26 [0001bca440 - 0001bca4a8] BOOTMEM
#27 [0001bca4c0 - 0001bca528] BOOTMEM
#28 [0001bca540 - 0001bca5a8] BOOTMEM
#29 [0001bca5c0 - 0001bca628] BOOTMEM
#30 [0001bca640 - 0001bca6a8] BOOTMEM
#31 [0001bca6c0 - 0001bca728] BOOTMEM
#32 [0001bca740 - 0001bca7a8] BOOTMEM
#33 [0001bca7c0 - 0001bca828] BOOTMEM
#34 [0001bca840 - 0001bca8a8] BOOTMEM
#35 [0001bca8c0 - 0001bca928] BOOTMEM
#36 [0001bca940 - 0001bca9a8] BOOTMEM
#37 [0001bca9c0 - 0001bcaa28] BOOTMEM
#38 [0001bcaa40 - 0001bcaaa8] BOOTMEM
#39 [0001bcaac0 - 0001bcab28] BOOTMEM
#40 [0001bcab40 - 0001bcaba8] BOOTMEM
#41 [0001bcabc0 - 0001bcac28] BOOTMEM
#42 [0001bcac40 - 0001bcaca8] BOOTMEM
#43 [0001bcacc0 - 0001bcad28] BOOTMEM
#44 [0001bcad40 - 0001bcada2] BOOTMEM
#45 [0001bcadc0 - 0001bcae22] BOOTMEM
#46 [0001c00000 - 0001c1b000] BOOTMEM
#47 [0001c80000 - 0001c9b000] BOOTMEM
#48 [0001d00000 - 0001d1b000] BOOTMEM
#49 [0001d80000 - 0001d9b000] BOOTMEM
#50 [0001baafc0 - 0001baafc8] BOOTMEM
#51 [0001bcae40 - 0001bcae48] BOOTMEM
#52 [0001bcae80 - 0001bcae90] BOOTMEM
#53 [0001bcaec0 - 0001bcaee0] BOOTMEM
#54 [0001bce000 - 0001bce130] BOOTMEM
#55 [0001bcaf00 - 0001bcaf50] BOOTMEM
#56 [0001bcaf80 - 0001bcafd0] BOOTMEM
#57 [0001bce140 - 0001bd6140] BOOTMEM
#58 [0001bcc000 - 0001bcc340] BOOTMEM
#59 [0001d9b000 - 0005d9b000] BOOTMEM
#60 [0001bd6140 - 0001bf6140] BOOTMEM
#61 [0001c1b000 - 0001c5b000] BOOTMEM
#62 [0000016800 - 000001e800] BOOTMEM
Memory: 3968868k/5240832k available (4477k kernel code, 1136064k absent, 135900k reserved, 6267k data, 640k init)
Hierarchical RCU implementation.
RCU-based detection of stalled CPUs is enabled.
NR_IRQS:16576 nr_irqs:440
Console: colour VGA+ 80x25
console [tty1] enabled
console [ttyS0] enabled
Fast TSC calibration using PIT
Detected 3092.979 MHz processor.
Calibrating delay loop (skipped), value calculated using timer frequency.. 6185.95 BogoMIPS (lpj=30929790)
Security Framework initialized
Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
Mount-cache hash table entries: 256
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
using mwait in idle threads.
Performance Events: generic architected perfmon, Intel PMU driver.
... version: 3
... bit width: 48
... generic registers: 8
... value mask: 0000ffffffffffff
... max period: 000000007fffffff
... fixed-purpose events: 3
... event mask: 00000007000000ff
Freeing SMP alternatives: 32k freed
Setting APIC routing to flat
alloc irq_desc for 16 on node 0
alloc kstat_irqs on node 0
alloc irq_desc for 17 on node 0
alloc kstat_irqs on node 0
alloc irq_desc for 18 on node 0
alloc kstat_irqs on node 0
alloc irq_desc for 19 on node 0
alloc kstat_irqs on node 0
alloc irq_desc for 22 on node 0
alloc kstat_irqs on node 0
alloc irq_desc for 23 on node 0
alloc kstat_irqs on node 0
..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
CPU0: Intel(R) Core(TM) i5-2400 CPU @ 3.10GHz stepping 07
Booting Node 0, Processors #1 #2 #3 Ok.
Brought up 4 CPUs
Total of 4 processors activated (24744.07 BogoMIPS).
NET: Registered protocol family 16
PCI: Using configuration type 1 for base access
bio: create slab <bio-0> at 0
ACPI: Interpreter disabled.
vgaarb: loaded
SCSI subsystem initialized
libata version 3.00 loaded.
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Probing PCI hardware
PCI: Probing PCI hardware (bus 00)
pci 0000:00:02.0: reg 10: [mem 0xfb400000-0xfb7fffff 64bit]
pci 0000:00:02.0: reg 18: [mem 0xd0000000-0xdfffffff 64bit pref]
pci 0000:00:02.0: reg 20: [io 0xf000-0xf03f]
pci 0000:00:16.0: reg 10: [mem 0xfbe03000-0xfbe0300f 64bit]
pci 0000:00:16.0: PME# supported from D0 D3hot D3cold
pci 0000:00:16.0: PME# disabled
pci 0000:00:1a.0: reg 10: [mem 0xfbe02000-0xfbe023ff]
pci 0000:00:1a.0: PME# supported from D0 D3hot D3cold
pci 0000:00:1a.0: PME# disabled
pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
pci 0000:00:1c.0: PME# disabled
pci 0000:00:1c.1: PME# supported from D0 D3hot D3cold
pci 0000:00:1c.1: PME# disabled
pci 0000:00:1c.2: PME# supported from D0 D3hot D3cold
pci 0000:00:1c.2: PME# disabled
pci 0000:00:1c.3: PME# supported from D0 D3hot D3cold
pci 0000:00:1c.3: PME# disabled
pci 0000:00:1c.4: PME# supported from D0 D3hot D3cold
pci 0000:00:1c.4: PME# disabled
pci 0000:00:1c.5: PME# supported from D0 D3hot D3cold
pci 0000:00:1c.5: PME# disabled
pci 0000:00:1d.0: reg 10: [mem 0xfbe01000-0xfbe013ff]
pci 0000:00:1d.0: PME# supported from D0 D3hot D3cold
pci 0000:00:1d.0: PME# disabled
pci 0000:00:1f.2: reg 10: [io 0xf110-0xf117]
pci 0000:00:1f.2: reg 14: [io 0xf100-0xf103]
pci 0000:00:1f.2: reg 18: [io 0xf0f0-0xf0f7]
pci 0000:00:1f.2: reg 1c: [io 0xf0e0-0xf0e3]
pci 0000:00:1f.2: reg 20: [io 0xf0d0-0xf0df]
pci 0000:00:1f.2: reg 24: [io 0xf0c0-0xf0cf]
pci 0000:00:1f.3: reg 10: [mem 0xfbe00000-0xfbe000ff 64bit]
pci 0000:00:1f.3: reg 20: [io 0xf040-0xf05f]
pci 0000:00:1f.5: reg 10: [io 0xf0b0-0xf0b7]
pci 0000:00:1f.5: reg 14: [io 0xf0a0-0xf0a3]
pci 0000:00:1f.5: reg 18: [io 0xf090-0xf097]
pci 0000:00:1f.5: reg 1c: [io 0xf080-0xf083]
pci 0000:00:1f.5: reg 20: [io 0xf070-0xf07f]
pci 0000:00:1f.5: reg 24: [io 0xf060-0xf06f]
pci 0000:01:00.0: reg 10: [mem 0xfbd00000-0xfbd1ffff]
pci 0000:01:00.0: reg 18: [io 0xe000-0xe01f]
pci 0000:01:00.0: reg 1c: [mem 0xfbd20000-0xfbd23fff]
pci 0000:01:00.0: PME# supported from D0 D3hot D3cold
pci 0000:01:00.0: PME# disabled
pci 0000:00:1c.0: PCI bridge to [bus 01-01]
pci 0000:00:1c.0: bridge window [io 0xe000-0xefff]
pci 0000:00:1c.0: bridge window [mem 0xfbd00000-0xfbdfffff]
pci 0000:00:1c.0: bridge window [mem 0xfff00000-0x000fffff pref] (disabled)
pci 0000:02:00.0: reg 10: [mem 0xfbc00000-0xfbc1ffff]
pci 0000:02:00.0: reg 18: [io 0xd000-0xd01f]
pci 0000:02:00.0: reg 1c: [mem 0xfbc20000-0xfbc23fff]
pci 0000:02:00.0: PME# supported from D0 D3hot D3cold
pci 0000:02:00.0: PME# disabled
pci 0000:00:1c.1: PCI bridge to [bus 02-02]
pci 0000:00:1c.1: bridge window [io 0xd000-0xdfff]
pci 0000:00:1c.1: bridge window [mem 0xfbc00000-0xfbcfffff]
pci 0000:00:1c.1: bridge window [mem 0xfff00000-0x000fffff pref] (disabled)
pci 0000:03:00.0: reg 10: [mem 0xfbb00000-0xfbb1ffff]
pci 0000:03:00.0: reg 18: [io 0xc000-0xc01f]
pci 0000:03:00.0: reg 1c: [mem 0xfbb20000-0xfbb23fff]
pci 0000:03:00.0: PME# supported from D0 D3hot D3cold
pci 0000:03:00.0: PME# disabled
pci 0000:00:1c.2: PCI bridge to [bus 03-03]
pci 0000:00:1c.2: bridge window [io 0xc000-0xcfff]
pci 0000:00:1c.2: bridge window [mem 0xfbb00000-0xfbbfffff]
pci 0000:00:1c.2: bridge window [mem 0xfff00000-0x000fffff pref] (disabled)
pci 0000:04:00.0: reg 10: [mem 0xfba00000-0xfba1ffff]
pci 0000:04:00.0: reg 18: [io 0xb000-0xb01f]
pci 0000:04:00.0: reg 1c: [mem 0xfba20000-0xfba23fff]
pci 0000:04:00.0: PME# supported from D0 D3hot D3cold
pci 0000:04:00.0: PME# disabled
pci 0000:00:1c.3: PCI bridge to [bus 04-04]
pci 0000:00:1c.3: bridge window [io 0xb000-0xbfff]
pci 0000:00:1c.3: bridge window [mem 0xfba00000-0xfbafffff]
pci 0000:00:1c.3: bridge window [mem 0xfff00000-0x000fffff pref] (disabled)
pci 0000:05:00.0: reg 10: [mem 0xfb900000-0xfb91ffff]
pci 0000:05:00.0: reg 18: [io 0xa000-0xa01f]
pci 0000:05:00.0: reg 1c: [mem 0xfb920000-0xfb923fff]
pci 0000:05:00.0: PME# supported from D0 D3hot D3cold
pci 0000:05:00.0: PME# disabled
pci 0000:00:1c.4: PCI bridge to [bus 05-05]
pci 0000:00:1c.4: bridge window [io 0xa000-0xafff]
pci 0000:00:1c.4: bridge window [mem 0xfb900000-0xfb9fffff]
pci 0000:00:1c.4: bridge window [mem 0xfff00000-0x000fffff pref] (disabled)
pci 0000:06:00.0: reg 10: [mem 0xfb800000-0xfb81ffff]
pci 0000:06:00.0: reg 18: [io 0x9000-0x901f]
pci 0000:06:00.0: reg 1c: [mem 0xfb820000-0xfb823fff]
pci 0000:06:00.0: PME# supported from D0 D3hot D3cold
pci 0000:06:00.0: PME# disabled
pci 0000:00:1c.5: PCI bridge to [bus 06-06]
pci 0000:00:1c.5: bridge window [io 0x9000-0x9fff]
pci 0000:00:1c.5: bridge window [mem 0xfb800000-0xfb8fffff]
pci 0000:00:1c.5: bridge window [mem 0xfff00000-0x000fffff pref] (disabled)
vgaarb: device added: PCI:0000:00:02.0,decodes=io+mem,owns=io+mem,locks=none
pci 0000:00:1f.0: PIIX/ICH IRQ router [8086:1c5c]
PCI: pci_cache_line_size set to 64 bytes
reserve RAM buffer: 000000000009b800 - 000000000009ffff
reserve RAM buffer: 00000000bac7d000 - 00000000bbffffff
reserve RAM buffer: 00000000bacf2000 - 00000000bbffffff
reserve RAM buffer: 00000000bb000000 - 00000000bbffffff
reserve RAM buffer: 000000013fe00000 - 000000013fffffff
NetLabel: Initializing
NetLabel: domain hash size = 128
NetLabel: protocols = UNLABELED CIPSOv4
NetLabel: unlabeled traffic allowed by default
Switching to clocksource tsc
pnp: PnP ACPI: disabled
pci 0000:00:1c.0: PCI bridge to [bus 01-01]
pci 0000:00:1c.0: bridge window [io 0xe000-0xefff]
pci 0000:00:1c.0: bridge window [mem 0xfbd00000-0xfbdfffff]
pci 0000:00:1c.0: bridge window [mem pref disabled]
pci 0000:00:1c.1: PCI bridge to [bus 02-02]
pci 0000:00:1c.1: bridge window [io 0xd000-0xdfff]
pci 0000:00:1c.1: bridge window [mem 0xfbc00000-0xfbcfffff]
pci 0000:00:1c.1: bridge window [mem pref disabled]
pci 0000:00:1c.2: PCI bridge to [bus 03-03]
pci 0000:00:1c.2: bridge window [io 0xc000-0xcfff]
pci 0000:00:1c.2: bridge window [mem 0xfbb00000-0xfbbfffff]
pci 0000:00:1c.2: bridge window [mem pref disabled]
pci 0000:00:1c.3: PCI bridge to [bus 04-04]
pci 0000:00:1c.3: bridge window [io 0xb000-0xbfff]
pci 0000:00:1c.3: bridge window [mem 0xfba00000-0xfbafffff]
pci 0000:00:1c.3: bridge window [mem pref disabled]
pci 0000:00:1c.4: PCI bridge to [bus 05-05]
pci 0000:00:1c.4: bridge window [io 0xa000-0xafff]
pci 0000:00:1c.4: bridge window [mem 0xfb900000-0xfb9fffff]
pci 0000:00:1c.4: bridge window [mem pref disabled]
pci 0000:00:1c.5: PCI bridge to [bus 06-06]
pci 0000:00:1c.5: bridge window [io 0x9000-0x9fff]
pci 0000:00:1c.5: bridge window [mem 0xfb800000-0xfb8fffff]
pci 0000:00:1c.5: bridge window [mem pref disabled]
pci 0000:00:1c.0: PCI->APIC IRQ transform: INT A -> IRQ 17
pci 0000:00:1c.0: setting latency timer to 64
pci 0000:00:1c.1: PCI->APIC IRQ transform: INT B -> IRQ 16
pci 0000:00:1c.1: setting latency timer to 64
pci 0000:00:1c.2: PCI->APIC IRQ transform: INT C -> IRQ 18
pci 0000:00:1c.2: setting latency timer to 64
pci 0000:00:1c.3: PCI->APIC IRQ transform: INT D -> IRQ 19
pci 0000:00:1c.3: setting latency timer to 64
pci 0000:00:1c.4: PCI->APIC IRQ transform: INT A -> IRQ 17
pci 0000:00:1c.4: setting latency timer to 64
pci 0000:00:1c.5: PCI->APIC IRQ transform: INT B -> IRQ 16
pci 0000:00:1c.5: setting latency timer to 64
pci_bus 0000:00: resource 0 [io 0x0000-0xffff]
pci_bus 0000:00: resource 1 [mem 0x00000000-0xffffffffffffffff]
pci_bus 0000:01: resource 0 [io 0xe000-0xefff]
pci_bus 0000:01: resource 1 [mem 0xfbd00000-0xfbdfffff]
pci_bus 0000:02: resource 0 [io 0xd000-0xdfff]
pci_bus 0000:02: resource 1 [mem 0xfbc00000-0xfbcfffff]
pci_bus 0000:03: resource 0 [io 0xc000-0xcfff]
pci_bus 0000:03: resource 1 [mem 0xfbb00000-0xfbbfffff]
pci_bus 0000:04: resource 0 [io 0xb000-0xbfff]
pci_bus 0000:04: resource 1 [mem 0xfba00000-0xfbafffff]
pci_bus 0000:05: resource 0 [io 0xa000-0xafff]
pci_bus 0000:05: resource 1 [mem 0xfb900000-0xfb9fffff]
pci_bus 0000:06: resource 0 [io 0x9000-0x9fff]
pci_bus 0000:06: resource 1 [mem 0xfb800000-0xfb8fffff]
NET: Registered protocol family 2
IP route cache hash table entries: 131072 (order: 8, 1048576 bytes)
TCP established hash table entries: 524288 (order: 11, 8388608 bytes)
TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
TCP: Hash tables configured (established 524288 bind 65536)
TCP reno registered
UDP hash table entries: 2048 (order: 4, 65536 bytes)
UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes)
NET: Registered protocol family 1
pci 0000:00:02.0: Boot video device
PCI: CLS 64 bytes, default 64
PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
Placing 64MB software IO TLB between ffff880001d9b000 - ffff880005d9b000
software IO TLB at phys 0x1d9b000 - 0x5d9b000
platform rtc_cmos: registered platform RTC device (no PNP device found)
audit: initializing netlink socket (disabled)
type=2000 audit(1377045318.984:1): initialized
squashfs: version 4.0 (2009/01/31) Phillip Lougher
msgmni has been set to 7751
alg: No test for stdrng (krng)
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
pcieport 0000:00:1c.0: setting latency timer to 64
alloc irq_desc for 24 on node -1
alloc kstat_irqs on node -1
pcieport 0000:00:1c.0: irq 24 for MSI/MSI-X
pcieport 0000:00:1c.1: setting latency timer to 64
alloc irq_desc for 25 on node -1
alloc kstat_irqs on node -1
pcieport 0000:00:1c.1: irq 25 for MSI/MSI-X
pcieport 0000:00:1c.2: setting latency timer to 64
alloc irq_desc for 26 on node -1
alloc kstat_irqs on node -1
pcieport 0000:00:1c.2: irq 26 for MSI/MSI-X
pcieport 0000:00:1c.3: setting latency timer to 64
alloc irq_desc for 27 on node -1
alloc kstat_irqs on node -1
pcieport 0000:00:1c.3: irq 27 for MSI/MSI-X
pcieport 0000:00:1c.4: setting latency timer to 64
alloc irq_desc for 28 on node -1
alloc kstat_irqs on node -1
pcieport 0000:00:1c.4: irq 28 for MSI/MSI-X
pcieport 0000:00:1c.5: setting latency timer to 64
alloc irq_desc for 29 on node -1
alloc kstat_irqs on node -1
pcieport 0000:00:1c.5: irq 29 for MSI/MSI-X
------------[ cut here ]------------
WARNING: at fs/proc/generic.c:825 remove_proc_entry+0xc0/0x1e2()
Hardware name: M1-311F7
name 'fan'
Modules linked in:
Pid: 1, comm: swapper Not tainted 2.6.34msc64-32xx #30
Call Trace:
[<ffffffff810f681a>] ? remove_proc_entry+0xc0/0x1e2
[<ffffffff81032289>] ? warn_slowpath_common+0x77/0x8e
[<ffffffff810322fc>] ? warn_slowpath_fmt+0x51/0x59
[<ffffffff81157e74>] ? ida_get_new_above+0x166/0x187
[<ffffffff810f5bf9>] ? __xlate_proc_name+0x38/0xa6
[<ffffffff81ab7117>] ? acpi_fan_init+0x0/0x32
[<ffffffff810f5bb7>] ? proc_match+0x23/0x2d
[<ffffffff810f681a>] ? remove_proc_entry+0xc0/0x1e2
[<ffffffff811589b3>] ? kobject_release+0x0/0x5e
[<ffffffff81ab70c1>] ? acpi_button_init+0x0/0x56
[<ffffffff81ab7117>] ? acpi_fan_init+0x0/0x32
[<ffffffff81ab7140>] ? acpi_fan_init+0x29/0x32
[<ffffffff810001e1>] ? do_one_initcall+0x50/0x13d
[<ffffffff81a948d5>] ? kernel_init+0x146/0x1d0
[<ffffffff810035b4>] ? kernel_thread_helper+0x4/0x10
[<ffffffff81a9478f>] ? kernel_init+0x0/0x1d0
[<ffffffff810035b0>] ? kernel_thread_helper+0x0/0x10
---[ end trace a7919e7f17c0a725 ]---
Non-volatile memory driver v1.3
Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
brd: module loaded
loop: module loaded
Loading iSCSI transport class v2.0-870.
Loading Adaptec I2O RAID: Version 2.4 Build 5go
Detecting Adaptec I2O RAID controllers...
aic94xx: Adaptec aic94xx SAS/SATA driver version 1.0.3 loaded
scsi: <fdomain> Detection failed (no card)
QLogic Fibre Channel HBA Driver: 8.03.02-k2
iscsi: registered transport (qla4xxx)
QLogic iSCSI HBA Driver
Emulex LightPulse Fibre Channel SCSI driver 8.3.10
Copyright(c) 2004-2009 Emulex. All rights reserved.
Brocade BFA FC/FCOE SCSI driver - version: 2.1.2.1
DC390: clustering now enabled by default. If you get problems load
with "disable_clustering=1" and report to maintainers
mpt2sas version 04.100.01.00 loaded
3ware Storage Controller device driver for Linux v1.26.02.002.
3ware 9000 Storage Controller device driver for Linux v2.26.02.013.
LSI 3ware SAS/SATA-RAID Controller device driver for Linux v3.26.02.000.
ipr: IBM Power RAID SCSI Device Driver version: 2.5.0 (February 11, 2010)
RocketRAID 3xxx/4xxx Controller driver v1.6 (090910)
stex: Promise SuperTrak EX Driver version: 4.6.0000.4
ata_piix 0000:00:1f.2: version 2.13
ata_piix 0000:00:1f.2: PCI->APIC IRQ transform: INT B -> IRQ 19
ata_piix 0000:00:1f.2: MAP [ P0 P2 P1 P3 ]
ata_piix 0000:00:1f.2: SCR access via SIDPR is available but doesn't work
ata_piix 0000:00:1f.2: setting latency timer to 64
scsi0 : ata_piix
scsi1 : ata_piix
ata1: SATA max UDMA/133 cmd 0xf110 ctl 0xf100 bmdma 0xf0d0 irq 19
ata2: SATA max UDMA/133 cmd 0xf0f0 ctl 0xf0e0 bmdma 0xf0d8 irq 19
ata_piix 0000:00:1f.5: PCI->APIC IRQ transform: INT B -> IRQ 19
ata_piix 0000:00:1f.5: MAP [ P0 -- P1 -- ]
ata_piix 0000:00:1f.5: setting latency timer to 64
scsi2 : ata_piix
scsi3 : ata_piix
ata3: SATA max UDMA/133 cmd 0xf0b0 ctl 0xf0a0 bmdma 0xf070 irq 19
ata4: SATA max UDMA/133 cmd 0xf090 ctl 0xf080 bmdma 0xf078 irq 19
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
PNP: No PS/2 controller found. Probing ports directly.
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
cpuidle: using governor ladder
usbcore: registered new interface driver hiddev
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use
nf_conntrack.acct=1 kernel parameter, acct=1 nf_conntrack module option or
sysctl net.netfilter.nf_conntrack_acct=1 to enable it.
TCP bic registered
Initializing XFRM netlink socket
NET: Registered protocol family 17
registered taskstats version 1
ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata3.00: ATA-8: WDC WD5003ABYX-01WERA1, 01.01S02, max UDMA/133
ata3.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 0/32)
ata3.00: configured for UDMA/133
scsi 2:0:0:0: Direct-Access ATA WDC WD5003ABYX-0 01.0 PQ: 0 ANSI: 5
sd 2:0:0:0: Attached scsi generic sg0 type 0
sd 2:0:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/465 GiB)
sd 2:0:0:0: [sda] Write Protect is off
sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sda: sda1 sda2 sda3
sd 2:0:0:0: [sda] Attached SCSI disk
ata4: failed to resume link (SControl 0)
ata4: SATA link down (SStatus 4 SControl 0)
kjournald starting. Commit interval 5 seconds
EXT3-fs (sda2): mounted filesystem with writeback data mode
VFS: Mounted root (ext3 filesystem) readonly on device 8:2.
Freeing unused kernel memory: 640k freed
Write protecting the kernel read-only data: 10240k
Freeing unused kernel memory: 1648k freed
Freeing unused kernel memory: 1784k freed
EXT3-fs (sda2): using internal journal
emlog: version 0.41 running, using major number 241
e1000e: Intel(R) PRO/1000 Network Driver - 2.0.0-NAPI
e1000e: Copyright(c) 1999 - 2012 Intel Corporation.
e1000e 0000:01:00.0: Disabling ASPM L0s
e1000e 0000:01:00.0: PCI->APIC IRQ transform: INT A -> IRQ 16
e1000e 0000:01:00.0: setting latency timer to 64
alloc irq_desc for 30 on node -1
alloc kstat_irqs on node -1
e1000e 0000:01:00.0: irq 30 for MSI/MSI-X
e1000e 0000:01:00.0: eth0: (PCI Express:2.5GT/s:Width x1) 00:90:0b:27:4c:2a
e1000e 0000:01:00.0: eth0: Intel(R) PRO/1000 Network Connection
e1000e 0000:01:00.0: eth0: MAC: 5, PHY: 8, PBA No: FFFFFF-0FF
e1000e 0000:02:00.0: Disabling ASPM L0s
e1000e 0000:02:00.0: PCI->APIC IRQ transform: INT A -> IRQ 17
e1000e 0000:02:00.0: setting latency timer to 64
alloc irq_desc for 31 on node -1
alloc kstat_irqs on node -1
e1000e 0000:02:00.0: irq 31 for MSI/MSI-X
e1000e 0000:02:00.0: eth1: (PCI Express:2.5GT/s:Width x1) 00:90:0b:27:4c:2b
e1000e 0000:02:00.0: eth1: Intel(R) PRO/1000 Network Connection
e1000e 0000:02:00.0: eth1: MAC: 5, PHY: 8, PBA No: FFFFFF-0FF
e1000e 0000:03:00.0: Disabling ASPM L0s
e1000e 0000:03:00.0: PCI->APIC IRQ transform: INT A -> IRQ 18
e1000e 0000:03:00.0: setting latency timer to 64
alloc irq_desc for 32 on node -1
alloc kstat_irqs on node -1
e1000e 0000:03:00.0: irq 32 for MSI/MSI-X
e1000e 0000:03:00.0: eth2: (PCI Express:2.5GT/s:Width x1) 00:90:0b:27:4c:2c
e1000e 0000:03:00.0: eth2: Intel(R) PRO/1000 Network Connection
e1000e 0000:03:00.0: eth2: MAC: 5, PHY: 8, PBA No: FFFFFF-0FF
e1000e 0000:04:00.0: Disabling ASPM L0s
e1000e 0000:04:00.0: PCI->APIC IRQ transform: INT A -> IRQ 19
e1000e 0000:04:00.0: setting latency timer to 64
alloc irq_desc for 33 on node -1
alloc kstat_irqs on node -1
e1000e 0000:04:00.0: irq 33 for MSI/MSI-X
e1000e 0000:04:00.0: eth3: (PCI Express:2.5GT/s:Width x1) 00:90:0b:27:4c:2d
e1000e 0000:04:00.0: eth3: Intel(R) PRO/1000 Network Connection
e1000e 0000:04:00.0: eth3: MAC: 5, PHY: 8, PBA No: FFFFFF-0FF
e1000e 0000:05:00.0: Disabling ASPM L0s
e1000e 0000:05:00.0: PCI->APIC IRQ transform: INT A -> IRQ 16
e1000e 0000:05:00.0: setting latency timer to 64
alloc irq_desc for 34 on node -1
alloc kstat_irqs on node -1
e1000e 0000:05:00.0: irq 34 for MSI/MSI-X
e1000e 0000:05:00.0: eth4: (PCI Express:2.5GT/s:Width x1) 00:90:0b:27:4c:2e
e1000e 0000:05:00.0: eth4: Intel(R) PRO/1000 Network Connection
e1000e 0000:05:00.0: eth4: MAC: 5, PHY: 8, PBA No: FFFFFF-0FF
e1000e 0000:06:00.0: Disabling ASPM L0s
e1000e 0000:06:00.0: PCI->APIC IRQ transform: INT A -> IRQ 17
e1000e 0000:06:00.0: setting latency timer to 64
alloc irq_desc for 35 on node -1
alloc kstat_irqs on node -1
e1000e 0000:06:00.0: irq 35 for MSI/MSI-X
e1000e 0000:06:00.0: eth5: (PCI Express:2.5GT/s:Width x1) 00:90:0b:27:4c:2f
e1000e 0000:06:00.0: eth5: Intel(R) PRO/1000 Network Connection
e1000e 0000:06:00.0: eth5: MAC: 5, PHY: 8, PBA No: FFFFFF-0FF
e1000e 0000:01:00.0: irq 30 for MSI/MSI-X
e1000e 0000:01:00.0: irq 30 for MSI/MSI-X
e1000e 0000:02:00.0: irq 31 for MSI/MSI-X
e1000e 0000:02:00.0: irq 31 for MSI/MSI-X
e1000e 0000:03:00.0: irq 32 for MSI/MSI-X
e1000e 0000:03:00.0: irq 32 for MSI/MSI-X
e1000e 0000:04:00.0: irq 33 for MSI/MSI-X
e1000e 0000:04:00.0: irq 33 for MSI/MSI-X
e1000e 0000:05:00.0: irq 34 for MSI/MSI-X
e1000e 0000:05:00.0: irq 34 for MSI/MSI-X
e1000e 0000:06:00.0: irq 35 for MSI/MSI-X
e1000e 0000:06:00.0: irq 35 for MSI/MSI-X
ip_tables: (C) 2000-2006 Netfilter Core Team
e1000e: eth1 NIC Link is Up 100 Mbps Full Duplex, Flow Control: None
e1000e 0000:02:00.0: eth1: 10/100 speed: disabling TSO
Bridge firewalling registered
e1000e: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: None
Software Watchdog Timer: 0.07 initialized. soft_noboot=0 soft_margin=60 sec (nowayout= 0)
machzwd: MachZ ZF-Logic Watchdog driver initializing.
machzwd: no ZF-Logic found
WDT driver for the Winbond(TM) W83627HF/THF/HG Super I/O chip initialising.
w83627hf/thf/hg WDT: cannot register miscdev on minor=130 (err=-16)
alim7101_wdt: Steve Hill <st...@na...>.
alim7101_wdt: ALi M7101 PMU not present - WDT not set
usbcore: registered new interface driver pcwd_usb
pcwd_usb: Berkshire USB-PC Watchdog driver v1.02
w83877f_wdt: cannot register miscdev on minor=130 (err=-16)
W83977F WDT: W83977F WDT driver, v1.00
W83977F WDT: cannot register miscdev on minor=130 (err=-16)
802.1Q VLAN Support v1.8 Ben Greear <gr...@ca...>
All bugs added by David S. Miller <da...@re...>
Loading NAT Module v0.1
MSX Session Module Version 6.2Loading Account Class Module v0.1
NETAUTH: Init
Loading Account Class Module v0.1
ip_set version 4 loaded
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci_hcd 0000:00:1a.0: PCI->APIC IRQ transform: INT A -> IRQ 16
ehci_hcd 0000:00:1a.0: setting latency timer to 64
ehci_hcd 0000:00:1a.0: EHCI Host Controller
ehci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:1a.0: debug port 2
ehci_hcd 0000:00:1a.0: cache line size of 64 is not supported
ehci_hcd 0000:00:1a.0: irq 16, io mem 0xfbe02000
ehci_hcd 0000:00:1a.0: USB 2.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ehci_hcd 0000:00:1d.0: PCI->APIC IRQ transform: INT A -> IRQ 23
ehci_hcd 0000:00:1d.0: setting latency timer to 64
ehci_hcd 0000:00:1d.0: EHCI Host Controller
ehci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
ehci_hcd 0000:00:1d.0: debug port 2
ehci_hcd 0000:00:1d.0: cache line size of 64 is not supported
ehci_hcd 0000:00:1d.0: irq 23, io mem 0xfbe01000
ehci_hcd 0000:00:1d.0: USB 2.0 started, EHCI 1.00
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
uhci_hcd: USB Universal Host Controller Interface driver
usb 1-1: new high speed USB device using ehci_hcd and address 2
hub 1-1:1.0: USB hub found
hub 1-1:1.0: 4 ports detected
NETAUTH Device open: minor(0)
usb 2-1: new high speed USB device using ehci_hcd and address 2
hub 2-1:1.0: USB hub found
hub 2-1:1.0: 6 ports detected
-bash-3.1#
Output of lspci -vvv:
-bash-3.1# lspci -vvv
00:00.0 0600: 8086:0100 (rev 09)
Subsystem: 8086:0100
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 0
Capabilities: [e0] Vendor Specific Information
00:02.0 0300: 8086:0102 (rev 09)
Subsystem: 8086:0102
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 11
Region 0: Memory at fb400000 (64-bit, non-prefetchable) [size=4M]
Region 2: Memory at d0000000 (64-bit, prefetchable) [size=256M]
Region 4: I/O ports at f000 [size=64]
Capabilities: [90] Message Signalled Interrupts: 64bit- Queue=0/0 Enable-
Address: 00000000 Data: 0000
Capabilities: [d0] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [a4] #13 [0306]
00:16.0 0780: 8086:1c3a (rev 04)
Subsystem: 8086:1c3a
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 11
Region 0: Memory at fbe03000 (64-bit, non-prefetchable) [size=16]
Capabilities: [50] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [8c] Message Signalled Interrupts: 64bit+ Queue=0/0 Enable-
Address: 0000000000000000 Data: 0000
00:1a.0 0c03: 8086:1c2d (rev 05) (prog-if 20)
Subsystem: 8086:1c2d
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 0: Memory at fbe02000 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Debug port
Capabilities: [98] #13 [0306]
00:1c.0 0604: 8086:1c10 (rev b5)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 0000e000-0000efff
Memory behind bridge: fbd00000-fbdfffff
Prefetchable memory behind bridge: 00000000fff00000-0000000000000000
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [40] Express Root Port (Slot+) IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <64ns, L1 <1us
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed unknown, Width x1, ASPM L0s L1, Port 1
Link: Latency L0s <512ns, L1 <4us
Link: ASPM Disabled RCB 64 bytes CommClk+ ExtSynch-
Link: Speed 2.5Gb/s, Width x1
Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug- Surpise-
Slot: Number 0, PowerLimit 10.000000
Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
Slot: AttnInd Unknown, PwrInd Unknown, Power-
Root: Correctable- Non-Fatal- Fatal- PME-
Capabilities: [80] Message Signalled Interrupts: 64bit- Queue=0/0 Enable+
Address: fee0f00c Data: 4169
Capabilities: [90] #0d [0000]
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:1c.1 0604: 8086:1c12 (rev b5)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
I/O behind bridge: 0000d000-0000dfff
Memory behind bridge: fbc00000-fbcfffff
Prefetchable memory behind bridge: 00000000fff00000-0000000000000000
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [40] Express Root Port (Slot+) IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <64ns, L1 <1us
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed unknown, Width x1, ASPM L0s L1, Port 2
Link: Latency L0s <512ns, L1 <4us
Link: ASPM Disabled RCB 64 bytes CommClk+ ExtSynch-
Link: Speed 2.5Gb/s, Width x1
Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug- Surpise-
Slot: Number 1, PowerLimit 10.000000
Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
Slot: AttnInd Unknown, PwrInd Unknown, Power-
Root: Correctable- Non-Fatal- Fatal- PME-
Capabilities: [80] Message Signalled Interrupts: 64bit- Queue=0/0 Enable+
Address: fee0f00c Data: 4171
Capabilities: [90] #0d [0000]
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:1c.2 0604: 8086:1c14 (rev b5)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
I/O behind bridge: 0000c000-0000cfff
Memory behind bridge: fbb00000-fbbfffff
Prefetchable memory behind bridge: 00000000fff00000-0000000000000000
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [40] Express Root Port (Slot+) IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <64ns, L1 <1us
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed unknown, Width x1, ASPM L0s L1, Port 3
Link: Latency L0s <512ns, L1 <4us
Link: ASPM Disabled RCB 64 bytes CommClk+ ExtSynch-
Link: Speed 2.5Gb/s, Width x1
Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug- Surpise-
Slot: Number 2, PowerLimit 10.000000
Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
Slot: AttnInd Unknown, PwrInd Unknown, Power-
Root: Correctable- Non-Fatal- Fatal- PME-
Capabilities: [80] Message Signalled Interrupts: 64bit- Queue=0/0 Enable+
Address: fee0f00c Data: 4179
Capabilities: [90] #0d [0000]
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:1c.3 0604: 8086:1c16 (rev b5)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=04, subordinate=04, sec-latency=0
I/O behind bridge: 0000b000-0000bfff
Memory behind bridge: fba00000-fbafffff
Prefetchable memory behind bridge: 00000000fff00000-0000000000000000
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [40] Express Root Port (Slot+) IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <64ns, L1 <1us
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed unknown, Width x1, ASPM L0s L1, Port 4
Link: Latency L0s <512ns, L1 <4us
Link: ASPM Disabled RCB 64 bytes CommClk+ ExtSynch-
Link: Speed 2.5Gb/s, Width x1
Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug- Surpise-
Slot: Number 3, PowerLimit 10.000000
Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
Slot: AttnInd Unknown, PwrInd Unknown, Power-
Root: Correctable- Non-Fatal- Fatal- PME-
Capabilities: [80] Message Signalled Interrupts: 64bit- Queue=0/0 Enable+
Address: fee0f00c Data: 4181
Capabilities: [90] #0d [0000]
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:1c.4 0604: 8086:1c18 (rev b5)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=05, subordinate=05, sec-latency=0
I/O behind bridge: 0000a000-0000afff
Memory behind bridge: fb900000-fb9fffff
Prefetchable memory behind bridge: 00000000fff00000-0000000000000000
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [40] Express Root Port (Slot+) IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <64ns, L1 <1us
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed unknown, Width x1, ASPM L0s L1, Port 5
Link: Latency L0s <512ns, L1 <4us
Link: ASPM Disabled RCB 64 bytes CommClk+ ExtSynch-
Link: Speed 2.5Gb/s, Width x1
Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug- Surpise-
Slot: Number 4, PowerLimit 10.000000
Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
Slot: AttnInd Unknown, PwrInd Unknown, Power-
Root: Correctable- Non-Fatal- Fatal- PME-
Capabilities: [80] Message Signalled Interrupts: 64bit- Queue=0/0 Enable+
Address: fee0f00c Data: 4189
Capabilities: [90] #0d [0000]
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:1c.5 0604: 8086:1c1a (rev b5)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=06, subordinate=06, sec-latency=0
I/O behind bridge: 00009000-00009fff
Memory behind bridge: fb800000-fb8fffff
Prefetchable memory behind bridge: 00000000fff00000-0000000000000000
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [40] Express Root Port (Slot+) IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <64ns, L1 <1us
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed unknown, Width x1, ASPM L0s L1, Port 6
Link: Latency L0s <512ns, L1 <4us
Link: ASPM Disabled RCB 64 bytes CommClk+ ExtSynch-
Link: Speed 2.5Gb/s, Width x1
Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug- Surpise-
Slot: Number 5, PowerLimit 10.000000
Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
Slot: AttnInd Unknown, PwrInd Unknown, Power-
Root: Correctable- Non-Fatal- Fatal- PME-
Capabilities: [80] Message Signalled Interrupts: 64bit- Queue=0/0 Enable+
Address: fee0f00c Data: 4191
Capabilities: [90] #0d [0000]
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:1d.0 0c03: 8086:1c26 (rev 05) (prog-if 20)
Subsystem: 8086:1c26
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 23
Region 0: Memory at fbe01000 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Debug port
Capabilities: [98] #13 [0306]
00:1f.0 0601: 8086:1c5c (rev 05)
Subsystem: 8086:1c5c
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Capabilities: [e0] Vendor Specific Information
00:1f.2 0101: 8086:1c00 (rev 05) (prog-if 8f)
Subsystem: 8086:1c00
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 19
Region 0: I/O ports at f110 [size=8]
Region 1: I/O ports at f100 [size=4]
Region 2: I/O ports at f0f0 [size=8]
Region 3: I/O ports at f0e0 [size=4]
Region 4: I/O ports at f0d0 [size=16]
Region 5: I/O ports at f0c0 [size=16]
Capabilities: [70] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [b0] #13 [0306]
00:1f.3 0c05: 8086:1c22 (rev 05)
Subsystem: 8086:1c22
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin C routed to IRQ 11
Region 0: Memory at fbe00000 (64-bit, non-prefetchable) [size=256]
Region 4: I/O ports at f040 [size=32]
00:1f.5 0101: 8086:1c08 (rev 05) (prog-if 85)
Subsystem: 8086:1c08
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 19
Region 0: I/O ports at f0b0 [size=8]
Region 1: I/O ports at f0a0 [size=4]
Region 2: I/O ports at f090 [size=8]
Region 3: I/O ports at f080 [size=4]
Region 4: I/O ports at f070 [size=16]
Region 5: I/O ports at f060 [size=16]
Capabilities: [70] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [b0] #13 [0306]
01:00.0 0200: 8086:150c
Subsystem: 8086:0000
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 30
Region 0: Memory at fbd00000 (32-bit, non-prefetchable) [size=128K]
Region 2: I/O ports at e000 [size=32]
Region 3: Memory at fbd20000 (32-bit, non-prefetchable) [size=16K]
Capabilities: [c8] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [d0] Message Signalled Interrupts: 64bit+ Queue=0/0 Enable+
Address: 00000000fee0100c Data: 41d1
Capabilities: [e0] Express Endpoint IRQ 0
Device: Supported: MaxPayload 256 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <512ns, L1 <64us
Device: AtnBtn- AtnInd- PwrInd-
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+
Device: MaxPayload 128 bytes, MaxReadReq 512 bytes
Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s L1, Port 0
Link: Latency L0s <128ns, L1 <64us
Link: ASPM Disabled RCB 64 bytes CommClk+ ExtSynch-
Link: Speed 2.5Gb/s, Width x1
Capabilities: [a0] MSI-X: Enable- Mask- TabSize=1
Vector table: BAR=3 offset=00000000
PBA: BAR=3 offset=00002000
02:00.0 0200: 8086:150c
Subsystem: 8086:0000
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 31
Region 0: Memory at fbc00000 (32-bit, non-prefetchable) [size=128K]
Region 2: I/O ports at d000 [size=32]
Region 3: Memory at fbc20000 (32-bit, non-prefetchable) [size=16K]
Capabilities: [c8] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [d0] Message Signalled Interrupts: 64bit+ Queue=0/0 Enable+
Address: 00000000fee0200c Data: 41e1
Capabilities: [e0] Express Endpoint IRQ 0
Device: Supported: MaxPayload 256 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <512ns, L1 <64us
Device: AtnBtn- AtnInd- PwrInd-
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+
Device: MaxPayload 128 bytes, MaxReadReq 512 bytes
Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s L1, Port 0
Link: Latency L0s <128ns, L1 <64us
Link: ASPM Disabled RCB 64 bytes CommClk+ ExtSynch-
Link: Speed 2.5Gb/s, Width x1
Capabilities: [a0] MSI-X: Enable- Mask- TabSize=1
Vector table: BAR=3 offset=00000000
PBA: BAR=3 offset=00002000
03:00.0 0200: 8086:150c
Subsystem: 8086:0000
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 32
Region 0: Memory at fbb00000 (32-bit, non-prefetchable) [size=128K]
Region 2: I/O ports at c000 [size=32]
Region 3: Memory at fbb20000 (32-bit, non-prefetchable) [size=16K]
Capabilities: [c8] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [d0] Message Signalled Interrupts: 64bit+ Queue=0/0 Enable+
Address: 00000000fee0400c Data: 4122
Capabilities: [e0] Express Endpoint IRQ 0
Device: Supported: MaxPayload 256 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <512ns, L1 <64us
Device: AtnBtn- AtnInd- PwrInd-
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+
Device: MaxPayload 128 bytes, MaxReadReq 512 bytes
Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s L1, Port 0
Link: Latency L0s <128ns, L1 <64us
Link: ASPM Disabled RCB 64 bytes CommClk+ ExtSynch-
Link: Speed 2.5Gb/s, Width x1
Capabilities: [a0] MSI-X: Enable- Mask- TabSize=1
Vector table: BAR=3 offset=00000000
PBA: BAR=3 offset=00002000
04:00.0 0200: 8086:150c
Subsystem: 8086:0000
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 33
Region 0: Memory at fba00000 (32-bit, non-prefetchable) [size=128K]
Region 2: I/O ports at b000 [size=32]
Region 3: Memory at fba20000 (32-bit, non-prefetchable) [size=16K]
Capabilities: [c8] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [d0] Message Signalled Interrupts: 64bit+ Queue=0/0 Enable+
Address: 00000000fee0800c Data: 4142
Capabilities: [e0] Express Endpoint IRQ 0
Device: Supported: MaxPayload 256 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <512ns, L1 <64us
Device: AtnBtn- AtnInd- PwrInd-
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+
Device: MaxPayload 128 bytes, MaxReadReq 512 bytes
Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s L1, Port 0
Link: Latency L0s <128ns, L1 <64us
Link: ASPM Disabled RCB 64 bytes CommClk+ ExtSynch-
Link: Speed 2.5Gb/s, Width x1
Capabilities: [a0] MSI-X: Enable- Mask- TabSize=1
Vector table: BAR=3 offset=00000000
PBA: BAR=3 offset=00002000
05:00.0 0200: 8086:150c
Subsystem: 8086:0000
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 34
Region 0: Memory at fb900000 (32-bit, non-prefetchable) [size=128K]
Region 2: I/O ports at a000 [size=32]
Region 3: Memory at fb920000 (32-bit, non-prefetchable) [size=16K]
Capabilities: [c8] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [d0] Message Signalled Interrupts: 64bit+ Queue=0/0 Enable+
Address: 00000000fee0100c Data: 4152
Capabilities: [e0] Express Endpoint IRQ 0
Device: Supported: MaxPayload 256 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <512ns, L1 <64us
Device: AtnBtn- AtnInd- PwrInd-
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+
Device: MaxPayload 128 bytes, MaxReadReq 512 bytes
Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s L1, Port 0
Link: Latency L0s <128ns, L1 <64us
Link: ASPM Disabled RCB 64 bytes CommClk+ ExtSynch-
Link: Speed 2.5Gb/s, Width x1
Capabilities: [a0] MSI-X: Enable- Mask- TabSize=1
Vector table: BAR=3 offset=00000000
PBA: BAR=3 offset=00002000
06:00.0 0200: 8086:150c
Subsystem: 8086:0000
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 35
Region 0: Memory at fb800000 (32-bit, non-prefetchable) [size=128K]
Region 2: I/O ports at 9000 [size=32]
Region 3: Memory at fb820000 (32-bit, non-prefetchable) [size=16K]
Capabilities: [c8] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [d0] Message Signalled Interrupts: 64bit+ Queue=0/0 Enable+
Address: 00000000fee0200c Data: 4162
Capabilities: [e0] Express Endpoint IRQ 0
Device: Supported: MaxPayload 256 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <512ns, L1 <64us
Device: AtnBtn- AtnInd- PwrInd-
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+
Device: MaxPayload 128 bytes, MaxReadReq 512 bytes
Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s L1, Port 0
Link: Latency L0s <128ns, L1 <64us
Link: ASPM Disabled RCB 64 bytes CommClk+ ExtSynch-
Link: Speed 2.5Gb/s, Width x1
Capabilities: [a0] MSI-X: Enable- Mask- TabSize=1
Vector table: BAR=3 offset=00000000
PBA: BAR=3 offset=00002000
-bash-3.1#
DMESG after the kernel with the ACPI portions not compiled in:
-bash-3.1# dmesg
Linux version 2.6.34msg64_2xxx (ro...@lo...) (gcc version 4.1.2 20080704 (Red Hat 4.1.2-46)) #7 SMP Mon Jul 5 18:25:01 IST 2010
Command line: ro root=/dev/sda2 console=ttyS0,115200n8 console=tty1 ide=nodma pcie_aspm=off loglevel=0 acpi=off
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009b800 (usable)
BIOS-e820: 000000000009b800 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 0000000020000000 (usable)
BIOS-e820: 0000000020000000 - 0000000020200000 (reserved)
BIOS-e820: 0000000020200000 - 0000000040000000 (usable)
BIOS-e820: 0000000040000000 - 0000000040200000 (reserved)
BIOS-e820: 0000000040200000 - 00000000bac7d000 (usable)
BIOS-e820: 00000000bac7d000 - 00000000bacc6000 (ACPI NVS)
BIOS-e820: 00000000bacc6000 - 00000000bacce000 (ACPI data)
BIOS-e820: 00000000bacce000 - 00000000bacf0000 (reserved)
BIOS-e820: 00000000bacf0000 - 00000000bacf2000 (usable)
BIOS-e820: 00000000bacf2000 - 00000000bad03000 (reserved)
BIOS-e820: 00000000bad03000 - 00000000bad10000 (ACPI NVS)
BIOS-e820: 00000000bad10000 - 00000000bad37000 (reserved)
BIOS-e820: 00000000bad37000 - 00000000bad7a000 (ACPI NVS)
BIOS-e820: 00000000bad7a000 - 00000000bb000000 (usable)
BIOS-e820: 00000000bb800000 - 00000000bfa00000 (reserved)
BIOS-e820: 00000000fed1c000 - 00000000fed40000 (reserved)
BIOS-e820: 00000000ff000000 - 0000000100000000 (reserved)
BIOS-e820: 0000000100000000 - 000000013fe00000 (usable)
NX (Execute Disable) protection: active
DMI 2.7 present.
AMI BIOS detected: BIOS may corrupt low RAM, working around it.
e820 update range: 0000000000000000 - 0000000000010000 (usable) ==> (reserved)
e820 update range: 0000000000000000 - 0000000000001000 (usable) ==> (reserved)
e820 remove range: 00000000000a0000 - 0000000000100000 (usable)
No AGP bridge found
last_pfn = 0x13fe00 max_arch_pfn = 0x400000000
MTRR default type: uncachable
MTRR fixed ranges enabled:
00000-9FFFF write-back
A0000-BFFFF uncachable
C0000-CFFFF write-protect
D0000-E7FFF uncachable
E8000-FFFFF write-protect
MTRR variable ranges enabled:
0 base 000000000 mask F00000000 write-back
1 base 100000000 mask FC0000000 write-back
2 base 0BB800000 mask FFF800000 uncachable
3 base 0BC000000 mask FFC000000 uncachable
4 base 0C0000000 mask FC0000000 uncachable
5 base 13FE00000 mask FFFE00000 uncachable
6 disabled
7 disabled
8 disabled
9 disabled
x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
e820 update range: 00000000bb800000 - 0000000100000000 (usable) ==> (reserved)
last_pfn = 0xbb000 max_arch_pfn = 0x400000000
initial memory mapped : 0 - 20000000
found SMP MP-table at [ffff8800000fce60] fce60
init_memory_mapping: 0000000000000000-00000000bb000000
0000000000 - 00bb000000 page 2M
kernel direct mapping tables up to bb000000 @ 12000-16000
init_memory_mapping: 0000000100000000-000000013fe00000
0100000000 - 013fe00000 page 2M
kernel direct mapping tables up to 13fe00000 @ 14000-1a000
[ffffea0000000000-ffffea00045fffff] PMD -> [ffff880002600000-ffff880005dfffff] on node 0
Zone PFN ranges:
DMA 0x00000010 -> 0x00001000
DMA32 0x00001000 -> 0x00100000
Normal 0x00100000 -> 0x0013fe00
Movable zone start PFN for each node
early_node_map[7] active PFN ranges
0: 0x00000010 -> 0x0000009b
0: 0x00000100 -> 0x00020000
0: 0x00020200 -> 0x00040000
0: 0x00040200 -> 0x000bac7d
0: 0x000bacf0 -> 0x000bacf2
0: 0x000bad7a -> 0x000bb000
0: 0x00100000 -> 0x0013fe00
On node 0 totalpages: 1026192
DMA zone: 56 pages used for memmap
DMA zone: 0 pages reserved
DMA zone: 3923 pages, LIFO batch:0
DMA32 zone: 14280 pages used for memmap
DMA32 zone: 746301 pages, LIFO batch:31
Normal zone: 3577 pages used for memmap
Normal zone: 258055 pages, LIFO batch:31
Intel MultiProcessor Specification v1.4
MPTABLE: OEM ID: A M I
MPTA...
[truncated message content] |
