[brlcad-commits] SF.net SVN: brlcad:[63138] brlcad/trunk/doc/docbook/system/man1/en/rtedge. xml
Open Source Solid Modeling CAD
Brought to you by:
brlcad
From: <car...@us...> - 2014-10-08 20:43:45
|
Revision: 63138 http://sourceforge.net/p/brlcad/code/63138 Author: carlmoore Date: 2014-10-08 20:43:36 +0000 (Wed, 08 Oct 2014) Log Message: ----------- further addition to rtedge.xml , and add 3 blank spaces Modified Paths: -------------- brlcad/trunk/doc/docbook/system/man1/en/rtedge.xml Modified: brlcad/trunk/doc/docbook/system/man1/en/rtedge.xml =================================================================== --- brlcad/trunk/doc/docbook/system/man1/en/rtedge.xml 2014-10-08 20:07:53 UTC (rev 63137) +++ brlcad/trunk/doc/docbook/system/man1/en/rtedge.xml 2014-10-08 20:43:36 UTC (rev 63138) @@ -75,7 +75,7 @@ </varlistentry> <varlistentry> - <term><option>-a#</option></term> + <term><option>-a #</option></term> <listitem> <para> selects auto-sizing, and gives the view azimuth in degrees. Used with @@ -118,7 +118,7 @@ </varlistentry> <varlistentry> - <term><option>-e#</option></term> + <term><option>-e #</option></term> <listitem> <para>selects auto-sizing, and gives the view elevation in degrees. Used with <option>-a</option> @@ -280,7 +280,7 @@ </varlistentry> <varlistentry> - <term><option>-s#</option></term> + <term><option>-s #</option></term> <listitem> <para>specifies the number of rays to fire in the X and Y directions on a square grid. @@ -289,6 +289,45 @@ </varlistentry> <varlistentry> + <term><option>-t</option></term> + <listitem> + <para>causes reversal of the order of grid traversal (default is not to do that) + </para> + </listitem> + </varlistentry> + + <varlistentry> + <term><option>-u units</option></term> + <listitem> + <para>specifies units, with "model" being used for the units of the local model + </para> + </listitem> + </varlistentry> + + <varlistentry> + <term><option>-v #</option></term> + <listitem> + <para>sets the verbosity bit vector flags for <command>rtedge</command> . + Use -v 0 for no output or -v fff for all available output. + See include/brlcad/rtprivate.h for various bit definitions.</para> + </listitem> + </varlistentry> + + <varlistentry> + <term><option>-w #</option></term> + <listitem> + <para>defines the width of each scanline in pixels.</para> + </listitem> + </varlistentry> + + <varlistentry> + <term><option>-x#</option></term> + <listitem> + <para>Set librt debug flags to (hexadecimal) number.</para> + </listitem> + </varlistentry> + + <varlistentry> <term><option>-F framebuffer</option></term> <listitem> <para> @@ -354,12 +393,6 @@ </listitem> </varlistentry> <varlistentry> - <term><option>-x#</option></term> - <listitem> - <para>Set librt debug flags to (hexadecimal) number.</para> - </listitem> - </varlistentry> - <varlistentry> <term><option>-c</option></term> <listitem> <para> This was sent by the SourceForge.net collaborative development platform, the world's largest Open Source development site. |