Re: [Apcupsd-users] Missung values in Windows "Online Slave"

[Ted M. <te...@mi...>]

So in summary:

Query apcupsd on the router, get a full set of values

Query apcupsd on win 7, don't get a full set

apcupsd on windows 7 is set to query the apcupsd on the router.

Now, if you shut off apcupsd on the windows 7 system and run the
querytool on windows 7 and query the router - does it work?

If it does not - then check windows firewall.  If it does - then
something is wrong with the apcupsd binary on windows 7

Ted

On 3/1/2016 8:57 AM, Uwe Z. wrote:
> Hello!
>
> With the querytool I'm missing exactly the same things as in apctray
> when I query 127.0.0.1:3551.
>
> Regards
> Uwe
>
> On Tuesday, 03/01/2016 at 08:20 Ted wrote:
>
>> If you turn off apctray and run my querytool and query 127.0.0.1 : 3551
>> do you get a full set of values or are you missing values like apctray
>> was?
>
>> Ted
>
>> On 2/29/2016 10:26 PM, Uwe Z. wrote:
>>> Hello!
>>>
>>> apctray querys localhost (127.0.0.1 Port 3551) on my Win7.
>>>
>>> apcupsd should query the remote server since other values (like ITEMP,
>>> LINEV, LOADPCT,...) exactly match what I see in the server webgui and
>>> the APCUPSD query tool when it's running on the Win7 system directly
>>> querying the server.
>>>
>>> The local apcupsd server should be allowed to connect from localhost
>>> since otherwise I should get a "COMMLOST" from apctray I think (and
>>> I'd be missing more values as well).
>>>
>>> Regards
>>> Uwe
>>>
>>> On Tuesday, 03/01/2016 at 02:02 Ted wrote:
>>>
>>>> Make sure your apctray on Windows is
>>>> configured to query localhost and not the remote apcupsd server.
>>>> Make sure the local apcupsd server is configured to query the
>>>> remote apcupsd server.  Make sure your local apcupsd server is
>>>> configured to allow NIS connections from localhost.
>>>
>>>> Ted
>>>
>>>> On 2/29/2016 9:07 AM, Uwe Z. wrote:
>>>>> Hello!
>>>>>
>>>>> Sorry for remailing this again (this time with corrected version
>>>>> numbers).
>>>>>
>>>>> I'm missing some of the values in my Windows 7 installation of apcupsd
>>>>> version 3.14.13 (Thanks for the good work Adam!).
>>>>>
>>>>> In my setup the UPS is connected to my router which provides the
>>>>> network server through the apcupsd NIS. In the router webgui I can see
>>>>> all the values properly provided. apcupsd version here is 3.14.13 as
>>>>> well.
>>>>>
>>>>> On my Win7 system the apcupsd is configured as "online slave":
>>>>>
>>>>> UPSCABLE ether
>>>>> UPSTYPE net
>>>>> DEVICE<ip-of-my-router>:3551
>>>>>
>>>>> In apctray the following values are missing while being displayed on
>>>>> my router and in Win7 in Ted's APCUPSD Query Tool (Thanks for this,
>>>>> Ted!):
>>>>>
>>>>> DWAKE (not listed)
>>>>> DSHUTD (not listed)
>>>>> STESTI (not listed)
>>>>> REG1 (not listed)
>>>>> REG2 (not listed)
>>>>> REG3 (not listed)
>>>>> MANDATE (not listed)
>>>>> SERIALNO (empty)
>>>>> BATTDATE (empty)
>>>>> NOMOUTV (shows "-1 Volts" instead of "230 Volts")
>>>>> NOMBATTV (shows "0.0 Volts" instead of "24.0 Volts")
>>>>> EXTBATTS (not listed but might be omitted anyway)
>>>>> FIRMWARE (empty)
>>>>>
>>>>> Is there a reason for this, especially for the empty/ wrong ones?
>>>>>
>>>>> Regards,
>>>>> Uwe
>>>>>
>
>
> ------------------------------------------------------------------------------
> Site24x7 APM Insight: Get Deep Visibility into Application Performance
> APM + Mobile APM + RUM: Monitor 3 App instances at just $35/Month
> Monitor end-to-end web transactions and take corrective actions now
> Troubleshoot faster and improve end-user experience. Signup Now!
> http://pubads.g.doubleclick.net/gampad/clk?id=272487151&iu=/4140
> _______________________________________________
> Apcupsd-users mailing list
> Apc...@li...
> https://lists.sourceforge.net/lists/listinfo/apcupsd-users