#311 mcapi test fails on bf609 ezkit

[panmingquan]

mcapi test turns out to be failing on bf609 ezkit after the kernel builds ok.

bfin> bootm 0x2000000

Booting kernel from Legacy Image at 02000000 ...

Image Name: bf609-0.0-4.0.0-ADI-2014R1-pre-0
Image Type: Blackfin Linux Kernel Image (gzip compressed)
Data Size: 7267305 Bytes = 6.9 MiB
Load Address: 00001000
Entry Point: 0032dba8
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Starting Kernel at = 0032dba8
Linux version 4.0.0-ADI-2014R1-pre-00477-g0663a14-dirty (test@linux93-bf609-can) (gcc version 4.3.5 (ADI-master/git-db9494f) ) #2 Wed May 6 05:30:26 CST 2015
register early platform devices
bootconsole [early_shadow0] enabled
ERROR: Not running on ADSP-BF609: unknown CPUID 0x0000 Rev 0.0
bootconsole [early_BFuart0] enabled
early printk enabled on early_BFuart0
Board Memory: 128MB
Kernel Managed Memory: 124MB
Memory map:
fixedcode = 0x00000400-0x00000490
text = 0x00001000-0x00227ff0
rodata = 0x00228014-0x002e7340
bss = 0x002e8000-0x00300728
data = 0x00300740-0x0032a000
stack = 0x00328000-0x0032a000
init = 0x0032a000-0x00886000
available = 0x00886000-0x07b00000
DMA Zone = 0x07b00000-0x07c00000
Hardware Trace active and enabled
Blackfin support (C) 2004-2010 Analog Devices, Inc.
Compiled for ADSP-BF609 Rev 0.0
Blackfin Linux support by http://blackfin.uclinux.org/
Processor Speed: 500 MHz core clock, 125 MHz SCLk, 125 MHz SCLK0, 125 MHz SCLK1 and 250 MHz DCLK
NOMPU: setting up cplb tables
Instruction Cache Enabled for CPU0
External memory: cacheable in instruction cache
L2 SRAM : uncacheable in instruction cache
Data Cache Enabled for CPU0
External memory: cacheable (write-through) in data cache
L2 SRAM : uncacheable in data cache
Built 1 zonelists in Zone order, mobility grouping off. Total pages: 31242
Kernel command line: root=/dev/mtdblock0 rw mem=124M max_mem=128M icc_l2_mem=0x8000 earlyprintk=serial,uart0,57600 console=ttyBF0,57600 ip=10.100.4.50:10.100.4.174:192.168.0.1:255.255.255.0:"bf609-ezkit":eth0:off
PID hash table entries: 512 (order: -1, 2048 bytes)
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 116056K/125952K available (2203K kernel code, 166K rwdata, 764K rodata, 5488K init, 97K bss, 9896K reserved, 0K cma-reserved, 1024K DMA)
NR_IRQS:291
Configuring Blackfin Priority Driven Interrupts
Console: colour dummy device 80x25
Calibrating delay loop... 989.18 BogoMIPS (lpj=1978368)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
devtmpfs: initialized
Blackfin Scratchpad data SRAM: 4 KB
Blackfin L1 Data A SRAM: 16 KB (9 KB free)
Blackfin L1 Data B SRAM: 16 KB (16 KB free)
Blackfin L1 Instruction SRAM: 64 KB (49 KB free)
Blackfin L2 SRAM: 256 KB (224 KB free)
pinctrl core: initialized pinctrl subsystem
NET: Registered protocol family 16
Blackfin DMA Controller
ezkit_init(): registering device resources
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
mcp230xx: probe of 0-0023 failed with error -1
i2c-bfin-twi i2c-bfin-twi.0: Blackfin on-chip I2C TWI Contoller, regs_base@ffc01e00
i2c-bfin-twi i2c-bfin-twi.1: Blackfin on-chip I2C TWI Contoller, regs_base@ffc01f00
pps_core: LinuxPPS API ver. 1 registered
pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti giometti@linux.it
PTP clock support registered
NET: Registered protocol family 23
Switched to clocksource bfin_cs_cycles
NET: Registered protocol family 2
TCP established hash table entries: 1024 (order: 0, 4096 bytes)
TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
TCP: Hash tables configured (established 1024 bind 1024)
TCP: reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
io scheduler noop registered (default)
bfin-uart: Blackfin serial driver
bfin-uart.0: ttyBF0 at MMIO 0xffc02000 (irq = 88, base_baud = 7812500) is a BFIN-UART
console [ttyBF0] enabled
console [ttyBF0] enabled
bootconsole [early_BFuart0] disabled
bootconsole [early_BFuart0] disabled
bootconsole [early_shadow0] disabled
physmap platform flash device: 01000000 at b0000000
physmap-flash.0: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x000089 Chip ID 0x008821
Intel/Sharp Extended Query Table at 0x010A
Intel/Sharp Extended Query Table at 0x010A
Intel/Sharp Extended Query Table at 0x010A
Intel/Sharp Extended Query Table at 0x010A
Intel/Sharp Extended Query Table at 0x010A
Using buffer write method
Using auto-unlock on power-up/resume
cfi_cmdset_0001: Erase suspend on write enabled
Creating 3 MTD partitions on "physmap-flash.0":
0x000000000000-0x000000080000 : "bootloader(nor)"
0x000000080000-0x000000480000 : "linux kernel(nor)"
0x000000480000-0x000001000000 : "file system(nor)"
m25p80 spi0.59: w25q32 (4096 Kbytes)
Creating 3 MTD partitions on "m25p80":
0x000000000000-0x000000080000 : "bootloader(spi)"
0x000000080000-0x000000200000 : "linux kernel(spi)"
0x000000200000-0x000000400000 : "file system(spi)"
adi-spi3 adi-spi3.0: registered ADI SPI controller spi0
adi-spi3 adi-spi3.1: registered ADI SPI controller spi1
CAN device driver interface
bfin_can bfin_can.0: bfin_can device registered(&reg_base=ffc00a00, rx_irq=47, tx_irq=48, err_irq=49, sclk=125000000)
stmmaceth stmmaceth.0: no reset control found
stmmac - user ID: 0x10, Synopsys ID: 0x36
Ring mode enabled
DMA HW capability register supported
Enhanced/Alternate descriptors
Enabled extended descriptors
RX Checksum Offload Engine supported (type 2)
Wake-Up On Lan supported
Enable RX Mitigation via HW Watchdog Timer
libphy: stmmac: probed
eth0: PHY ID 20005c90 at 1 IRQ POLL (stmmac-0:01) active
usbcore: registered new interface driver usb-storage
input: bfin-rotary as /devices/platform/bfin-rotary/input/input0
i2c /dev entries driver
bfin_wdt: initialized: timeout=20 sec (nowayout=0)
Driver 'mmcblk' needs updating - please use bus_type methods
dma_alloc_init: dma_page @ 0x04bb5000 - 256 pages at 0x07b00000
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
icc icc.0: initialized
TCP: cubic registered
NET: Registered protocol family 17
can: controller area network core (rev 20120528 abi 9)
NET: Registered protocol family 29
can: raw protocol (rev 20120528)
can: broadcast manager protocol (rev 20120528 t)
can: netlink gateway (rev 20130117) max_hops=1
eth0: device MAC address 02:80:ad:20:31:e8
IP-Config: Gateway not on directly connected network
Freeing unused kernel memory: 5488K (0032a000 - 00886000)

BusyBox v1.23.1 (2015-05-06 05:20:36 CST) hush - the humble shell

root:/>successful boot attempt ifconfig etstmmaceth stmmaceth.0 eth0: Link is Up - 100Mbps/Full - flow control rx/tx
h0 10.100.4.50
root:/> Ethernet may has been activated already!
random: nonblocking pool is initialized
version
kernel: Linux release 4.0.0-ADI-2014R1-pre-00477-g0663a14-dirty, build #2 Wed May 6 05:30:26 CST 2015
toolchain: /home/test/workspace/src/kernel/label/BF609-EZKIT-CAN/output/host/usr/bin/bfin-linux-uclibc-gcc release gcc version 4.3.5 (ADI-master/git-db9494f)
user-dist: release git-104cbbe, build #1 Wed May 6 05:30:05 CST 2015
root:/>
Linux version: 4.0.0-ADI-2014R1-pre-00477-g0663a14-dirty
GCC version: 4.3.5 (ADI-master/git-db9494f)
user-dist version: git-104cbbe

** STEP 3: Starting test

all_bin_num=7
cd /bin
root:/bin>
PASS: Copy BF609_MCAPI_msg_Core1.dxe to target board
echo 1 > /proc/sys/kernel/printk
root:/bin> ./icc_loader -l ./BF609_MCAPI_msg_Core1.dxe
load elf code to core B
writing to 0xff600000, 0x9aee bytes: OK
writing to 0xff5010f0, 0x233c bytes: OK
writing to 0xff503988, 0xe4 bytes: OK
writing to 0xff500000, 0x59b bytes: OK
writing to 0xff50059c, 0x34 bytes: OK
writing to 0xff5005d0, 0xb20 bytes: OK
writing to 0xff50342c, 0x55c bytes: OK
writing to 0xc80a8000, 0x1a bytes: OK
writing to 0xc8088210, 0xc00 bytes: OK
writing to 0xc80a801c, 0x10 bytes: OK
root:/bin>
Case 1 ...PASS

Case 1 ...PASS

root:/bin> cces_msg1
MCAPI_DEBUG:mcapi_trans_initialize 865
MCAPI_DEBUG:mcapi_trans_initialize_ 825
MCAPI_DEBUG:mcapi_trans_initialize_ 848
MCAPI_DEBUG:mcapi_trans_initialize_ 853 db addr 00000000 size 2c34c
MCAPI_DEBUG:mcapi_trans_initialize_ 857
WRONG: line=56
root:/bin> The case is ending!! corea_case_status: 0, execption_count 0!!
case fail!!!
cat /tmp/ ; dmesg
cat: can't open '/tmp/': No such file or directory
Linux version 4.0.0-ADI-2014R1-pre-00477-g0663a14-dirty (test@linux93-bf609-can) (gcc version 4.3.5 (ADI-master/git-db9494f) ) #2 Wed May 6 05:30:26 CST 2015
register early platform devices