After wake up from standby or mem mode, ethernet fails to work in bf609-ezkit.
--
Linux version 3.16.0-rc4-ADI-2014R1-pre-00376-gb6f3b82-dirty (test@linux83-bf609-usbhost) (gcc version 4.3.5 (ADI-master/git-db9494f) ) #4 Fri 4
register early platform devices
bootconsole [early_shadow0] enabled
ERROR: Not running on ADSP-BF609: unknown CPUID 0x0000 Rev 0.0
bootconsole [early_BFuart0] enabled
early printk enabled on early_BFuart0
Board Memory: 128MB
Kernel Managed Memory: 128MB
Memory map:
fixedcode = 0x00000400-0x00000490
text = 0x00001000-0x00202d30
rodata = 0x00202d54-0x002af760
bss = 0x002b0000-0x002c8bc0
data = 0x002c8bc0-0x002f4000
stack = 0x002f2000-0x002f4000
init = 0x002f4000-0x008e1000
available = 0x008e1000-0x07f00000
DMA Zone = 0x07f00000-0x08000000
Hardware Trace active and enabled
Blackfin support (C) 2004-2010 Analog Devices, Inc.
Compiled for ADSP-BF609 Rev 0.0
Blackfin Linux support by http://blackfin.uclinux.org/
Processor Speed: 500 MHz core clock, 125 MHz SCLk, 125 MHz SCLK0, 125 MHz SCLK1 and 250 MHz DCLK
NOMPU: setting up cplb tables
Instruction Cache Enabled for CPU0
External memory: cacheable in instruction cache
L2 SRAM : uncacheable in instruction cache
Data Cache Enabled for CPU0
External memory: cacheable (write-back) in data cache
L2 SRAM : uncacheable in data cache
Built 1 zonelists in Zone order, mobility grouping off. Total pages: 32258
Kernel command line: root=/dev/mtdblock0 rw clkin_hz=(25000000) earlyprintk=serial,uart0,57600 console=ttyBF0,57600 ip=10.100.4.50:10.100.4.174f
PID hash table entries: 512 (order: -1, 2048 bytes)
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 119788K/130048K available (2055K kernel code, 173K rwdata, 690K rodata, 6068K init, 98K bss, 10260K reserved, 1024K DMA)
NR_IRQS:291
Configuring Blackfin Priority Driven Interrupts
Console: colour dummy device 80x25
Calibrating delay loop... 995.32 BogoMIPS (lpj=1990656)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
devtmpfs: initialized
Blackfin Scratchpad data SRAM: 4 KB
Blackfin L1 Data A SRAM: 16 KB (9 KB free)
Blackfin L1 Data B SRAM: 16 KB (16 KB free)
Blackfin L1 Instruction SRAM: 64 KB (49 KB free)
Blackfin L2 SRAM: 256 KB (256 KB free)
pinctrl core: initialized pinctrl subsystem
NET: Registered protocol family 16
Blackfin DMA Controller
ezkit_init(): registering device resources
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
i2c-bfin-twi i2c-bfin-twi.0: Blackfin on-chip I2C TWI Contoller, regs_base@ffc01e00
i2c-bfin-twi i2c-bfin-twi.1: Blackfin on-chip I2C TWI Contoller, regs_base@ffc01f00
pps_core: LinuxPPS API ver. 1 registered
pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti giometti@linux.it
PTP clock support registered
NET: Registered protocol family 23
Switched to clocksource bfin_cs_cycles
NET: Registered protocol family 2
TCP established hash table entries: 1024 (order: 0, 4096 bytes)
TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
TCP: Hash tables configured (established 1024 bind 1024)
TCP: reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
msgmni has been set to 233
io scheduler noop registered (default)
bfin-uart: Blackfin serial driver
bfin-uart.0: ttyBF0 at MMIO 0xffc02000 (irq = 88, base_baud = 7812500) is a BFIN-UART
console [ttyBF0] enabled
console [ttyBF0] enabled
bootconsole [early_BFuart0] disabled
bootconsole [early_BFuart0] disabled
bootconsole [early_shadow0] disabled
physmap platform flash device: 01000000 at b0000000
physmap-flash physmap-flash.0: map_probe failed
CAN device driver interface
bfin_can bfin_can.0: bfin_can device registered(®_base=ffc00a00, rx_irq=47, tx_irq=48, err_irq=49, sclk=125000000)
stmmaceth stmmaceth.0: no reset control found
stmmac - user ID: 0x10, Synopsys ID: 0x36
Ring mode enabled
DMA HW capability register supported
Enhanced/Alternate descriptors
Enabled extended descriptors
RX Checksum Offload Engine supported (type 2)
Wake-Up On Lan supported
Enable RX Mitigation via HW Watchdog Timer
libphy: stmmac: probed
eth0: PHY ID 20005c90 at 1 IRQ POLL (stmmac-0:01) active
usbcore: registered new interface driver usb-storage
input: bfin-rotary as /devices/platform/bfin-rotary/input/input0
i2c /dev entries driver
bfin_wdt: initialized: timeout=20 sec (nowayout=0)
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
TCP: cubic registered
NET: Registered protocol family 17
can: controller area network core (rev 20120528 abi 9)
NET: Registered protocol family 29
can: raw protocol (rev 20120528)
can: broadcast manager protocol (rev 20120528 t)
can: netlink gateway (rev 20130117) max_hops=1
eth0: device MAC address 02:80:ad:20:31:e8
dma_alloc_init: dma_page @ 0x04fa4000 - 256 pages at 0x07f00000
IP-Config: Complete:
device=eth0, hwaddr=02:80:ad:20:31:e8, ipaddr=10.100.4.50, mask=255.255.255.0, gw=10.100.4.174
host="bf609-ezkit", domain=, nis-domain=(none)
bootserver=10.100.4.174, rootserver=10.100.4.174, rootpath=
Freeing unused kernel memory: 6068K (002f4000 - 008e1000)
BusyBox v1.22.1 (2014-07-17 23:53:04 CST) hush - the humble shell
root:/> stmmaceth stmmaceth.0 eth0: Link is Up - 100Mbps/Full - flow control rx/tx
root:/> echo mem > /sys/power/state
PM: Syncing filesystems ... done.
Freezing user space processes ... (elapsed 0.011 seconds) done.
Freezing remaining freezable tasks ... (elapsed 0.001 seconds) done.
Suspending console(s) (use no_console_suspend to debug)
random: nonblocking pool is initialized
PM: suspend of devices complete after 1.539 msecs
PM: late suspend of devices complete after 0.458 msecs
PM: noirq suspend of devices complete after 0.657 msecs
PM: noirq resume of devices complete after 0.489 msecs
PM: early resume of devices complete after 0.405 msecs
PM: resume of devices complete after 13.898 msecs
Restarting tasks ... done.
root:/>
root:/>
root:/>
root:/>
root:/> ifconfig
eth0 Link encap:Ethernet HWaddr 02:80:AD:20:31:E8
inet addr:10.100.4.50 Bcast:10.100.4.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
Interrupt:75
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:65536 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
root:/> ping 10.100.4.174
PING 10.100.4.174 (10.100.4.174): 56 data bytes
--- 10.100.4.174 ping statistics ---
5 packets transmitted, 0 packets received, 100% packet loss
root:/>
--
Hi Vivi,
Is this bug from the power_ethernet test? If so, I can take a look at it.
Regards,
Andre.
need reset priv->oldlink priv->speed after phy_stop
It looks from the regression log that the results gets better, but still doesn't go to the end of the test.
root:/>successful boot attempt ifconfig ethstmmaceth stmmaceth.0 eth0: Link is Up - 100Mbps/Full - flow control rx/tx
0 10.100.4.50
root:/> Ethernet may has been activated already!
random: nonblocking pool is initialized
version
kernel: Linux release 3.16.0-ADI-2014R1-pre-00401-gce2a0f2-dirty, build #2 Thu Aug 14 23:15:04 CST 2014
toolchain: /home/test/workspace/src/kernel/label/BF609-EZKIT-USBHOST/output/host/usr/bin/bfin-linux-uclibc-gcc release gcc version 4.3.5 (ADI-master/git-46c6a72)
user-dist: release git-de663ec, build #1 Thu Aug 14 23:11:25 CST 2014
root:/>
Linux version: 3.16.0-ADI-2014R1-pre-00401-gce2a0f2-dirty
GCC version: 4.3.5 (ADI-master/git-46c6a72)
user-dist version: git-de663ec
** STEP 3: Start testing
[6n
root:/> ping 10.100.4.174 -c 5
PING 10.100.4.174 (10.100.4.174): 56 data bytes
64 bytes from 10.100.4.174: seq=0 ttl=64 time=1.989 ms
64 bytes from 10.100.4.174: seq=1 ttl=64 time=1.032 ms
64 bytes from 10.100.4.174: seq=2 ttl=64 time=1.022 ms
64 bytes from 10.100.4.174: seq=3 ttl=64 time=1.032 ms
64 bytes from 10.100.4.174: seq=4 ttl=64 time=1.038 ms
--- 10.100.4.174 ping statistics ---
5 packets transmitted, 5 packets received, 0% packet loss
round-trip min/avg/max = 1.022/1.222/1.989 ms
root:/>
Case 1 ...PASS
Case 1 ...PASS
cat /proc/mounts
rootfs / rootfs rw 0 0
devtmpfs /dev devtmpfs rw,relatime,mode=0755 0 0
proc /proc proc rw,nosuid,nodev,noexec,relatime 0 0
sysfs /sys sysfs rw,nosuid,nodev,noexec,relatime 0 0
mdev /dev tmpfs rw,nosuid,relatime,mode=0755,size=10M 0 0
devpts /dev/pts devpts rw,nosuid,noexec,relatime,mode=600 0 0
var /var tmpfs rw,relatime 0 0
tmp /tmp tmpfs rw,nosuid,nodev,relatime,mode=777 0 0
debugfs /sys/kernel/debug debugfs rw,relatime 0 0
root:/>
Case 2 ...PASS
Case 2 ...PASS
ls /sys/power
pm_async pm_freeze_timeout state wakeup_count
root:/>
Case 3 ...PASS
Case 3 ...PASS
spawn /bin/bash
suites/power_ethernet$ sut:~/workspace/src/kernel/label/BF609-EZKIT-USBHOST/tests
Password:
root@linux83-bf609-usbhost:power_ethernet#
Case 4 ...PASS
Case 4 ...PASS
[6necho mem > /sys/power/state
PM: Syncing filesystems ... done.
Freezing user space processes ... (elapsed 0.011 seconds) done.
Freezing remaining freezable tasks ... (elapsed 0.001 seconds) done.
Suspending console(s) (use no_console_suspend to debug)
Case 5 ...PASS
Case 5 ...PASS
reset_board 4
powering OFF board attached to printer port pin 4
powering ON board attached to printer port pin 4
Case 6 ...PASS
Case 6 ...PASS
PM: suspend of devices complete after 1.395 msecs
PM: late suspend of devices complete after 0.528 msecs
PM: noirq suspend of devices complete after 0.725 msecs
PM: noirq resume of devices complete after 0.627 msecs
PM: early resume of devices complete after 0.454 msecs
PM: resume of devices complete after 13.857 msecs
Restarting tasks ... done.
root:/>
Case 7 ...PASS
Case 7 ...PASS
stmmaceth stmmaceth.0 eth0: Link is Up - 100Mbps/Full - flow control rx/tx
ifconfig
eth0 Link encap:Ethernet HWaddr 02:80:AD:20:31:E8
inet addr:10.100.4.50 Bcast:10.100.4.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:7 errors:0 dropped:0 overruns:0 frame:0
TX packets:7 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:610 (610.0 B) TX bytes:574 (574.0 B)
Interrupt:75
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:65536 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
root:/>
Case 8 ...PASS
Case 8 ...PASS
ping 10.100.4.174 -c 5
PING 10.100.4.174 (10.100.4.174): 56 data bytes
64 bytes from 10.100.4.174: seq=0 ttl=64 time=1.073 ms
64 bytes from 10.100.4.174: seq=1 ttl=64 time=1.028 ms
64 bytes from 10.100.4.174: seq=2 ttl=64 time=1.039 ms
64 bytes from 10.100.4.174: seq=3 ttl=64 time=1.012 ms
64 bytes from 10.100.4.174: seq=4 ttl=64 time=1.037 ms
--- 10.100.4.174 ping statistics ---
5 packets transmitted, 5 packets received, 0% packet loss
round-trip min/avg/max = 1.012/1.037/1.073 ms
root:/>
Case 8 ...PASS
Case 8 ...PASS
PM test case 1 round 1 pass
echo mem > /sys/power/state
PM: Syncing filesystems ... done.
Freezing user space processes ... (elapsed 0.000 seconds) done.
Freezing remaining freezable tasks ... (elapsed 0.001 seconds) done.
Suspending console(s) (use no_console_suspend to debug)
Case 9 ...PASS
Case 9 ...PASS
root@linux83-bf609-usbhost:power_ethernet# reset_board 4
powering OFF board attached to printer port pin 4
powering ON board attached to printer port pin 4
Case 10 ...PASS
Case 10 ...PASS
PM: suspend of devices complete after 1.381 msecs
PM: late suspend of devices complete after 0.532 msecs
PM: noirq suspend of devices complete after 0.729 msecs
PM: noirq resume of devices complete after 0.600 msecs
PM: early resume of devices complete after 0.459 msecs
PM: resume of devices complete after 13.916 msecs
Restarting tasks ... done.
root:/>
Case 11 ...PASS
Case 11 ...PASS
stmmaceth stmmaceth.0 eth0: Link is Up - 100Mbps/Full - flow control rx/tx
ifconfig
eth0 Link encap:Ethernet HWaddr 02:80:AD:20:31:E8
inet addr:10.100.4.50 Bcast:10.100.4.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:12 errors:0 dropped:0 overruns:0 frame:0
TX packets:12 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:1100 (1.0 KiB) TX bytes:1064 (1.0 KiB)
Interrupt:75
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:65536 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
root:/>
Case 12 ...PASS
Case 12 ...PASS
ping 10.100.4.174 -c 5
PING 10.100.4.174 (10.100.4.174): 56 data bytes
64 bytes from 10.100.4.174: seq=0 ttl=64 time=1.071 ms
64 bytes from 10.100.4.174: seq=1 ttl=64 time=1.041 ms
64 bytes from 10.100.4.174: seq=2 ttl=64 time=1.034 ms
64 bytes from 10.100.4.174: seq=3 ttl=64 time=1.032 ms
64 bytes from 10.100.4.174: seq=4 ttl=64 time=1.031 ms
--- 10.100.4.174 ping statistics ---
5 packets transmitted, 5 packets received, 0% packet loss
round-trip min/avg/max = 1.031/1.041/1.071 ms
root:/>
Case 12 ...PASS
Case 12 ...PASS
PM test case 1 round 2 pass
echo mem > /sys/power/state
PM: Syncing filesystems ... done.
Freezing user space processes ... (elapsed 0.001 seconds) done.
Freezing remaining freezable tasks ... (elapsed 0.001 seconds) done.
Suspending console(s) (use no_console_suspend to debug)
Case 13 ...PASS
Case 13 ...PASS
root@linux83-bf609-usbhost:power_ethernet# reset_board 4
powering OFF board attached to printer port pin 4
powering ON board attached to printer port pin 4
Case 14 ...PASS
Case 14 ...PASS
PM: suspend of devices complete after 1.384 msecs
PM: late suspend of devices complete after 0.536 msecs
PM: noirq suspend of devices complete after 0.734 msecs
PM: noirq resume of devices complete after 0.542 msecs
PM: early resume of devices complete after 0.459 msecs
PM: resume of devices complete after 13.953 msecs
Restarting tasks ... done.
root:/>
Case 15 ...PASS
Case 15 ...PASS
stmmaceth stmmaceth.0 eth0: Link is Up - 100Mbps/Full - flow control rx/tx
ifconfig
eth0 Link encap:Ethernet HWaddr 02:80:AD:20:31:E8
inet addr:10.100.4.50 Bcast:10.100.4.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:17 errors:0 dropped:0 overruns:0 frame:0
TX packets:18 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:1590 (1.5 KiB) TX bytes:1596 (1.5 KiB)
Interrupt:75
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:65536 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
root:/>
Case 16 ...PASS
Case 16 ...PASS
ping 10.100.4.174 -c 5
PING 10.100.4.174 (10.100.4.174): 56 data bytes
64 bytes from 10.100.4.174: seq=0 ttl=64 time=1.096 ms
64 bytes from 10.100.4.174: seq=1 ttl=64 time=0.979 ms
64 bytes from 10.100.4.174: seq=2 ttl=64 time=1.034 ms
64 bytes from 10.100.4.174: seq=3 ttl=64 time=1.028 ms
64 bytes from 10.100.4.174: seq=4 ttl=64 time=1.019 ms
--- 10.100.4.174 ping statistics ---
5 packets transmitted, 5 packets received, 0% packet loss
round-trip min/avg/max = 0.979/1.031/1.096 ms
root:/>
Case 16 ...PASS
Case 16 ...PASS
PM test case 1 round 3 pass
echo mem > /sys/power/state
PM: Syncing filesystems ... done.
Freezing user space processes ... (elapsed 0.000 seconds) done.
Freezing remaining freezable tasks ... (elapsed 0.001 seconds) done.
Suspending console(s) (use no_console_suspend to debug)
Case 17 ...PASS
Case 17 ...PASS
root@linux83-bf609-usbhost:power_ethernet# reset_board 4
powering OFF board attached to printer port pin 4
powering ON board attached to printer port pin 4
Case 18 ...PASS
Case 18 ...PASS
PM: suspend of devices complete after 1.390 msecs
PM: late suspend of devices complete after 0.540 msecs
PM: noirq suspend of devices complete after 0.738 msecs
PM: noirq resume of devices complete after 0.607 msecs
PM: early resume of devices complete after 0.464 msecs
PM: resume of devices complete after 13.935 msecs
Restarting tasks ... done.
root:/>
Case 19 ...PASS
Case 19 ...PASS
stmmaceth stmmaceth.0 eth0: Link is Up - 100Mbps/Full - flow control rx/tx
ifconfig
eth0 Link encap:Ethernet HWaddr 02:80:AD:20:31:E8
inet addr:10.100.4.50 Bcast:10.100.4.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:23 errors:0 dropped:0 overruns:0 frame:0
TX packets:24 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:2140 (2.0 KiB) TX bytes:2128 (2.0 KiB)
Interrupt:75
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:65536 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
root:/>
Case 20 ...PASS
Case 20 ...PASS
ping 10.100.4.174 -c 5
PING 10.100.4.174 (10.100.4.174): 56 data bytes
64 bytes from 10.100.4.174: seq=0 ttl=64 time=1.811 ms
64 bytes from 10.100.4.174: seq=1 ttl=64 time=1.013 ms
64 bytes from 10.100.4.174: seq=2 ttl=64 time=1.028 ms
64 bytes from 10.100.4.174: seq=3 ttl=64 time=1.053 ms
64 bytes from 10.100.4.174: seq=4 ttl=64 time=1.023 ms
--- 10.100.4.174 ping statistics ---
5 packets transmitted, 5 packets received, 0% packet loss
round-trip min/avg/max = 1.013/1.185/1.811 ms
root:/>
Case 20 ...PASS
Case 20 ...PASS
PM test case 1 round 4 pass
echo mem > /sys/power/state
PM: Syncing filesystems ... done.
Freezing user space processes ... (elapsed 0.000 seconds) done.
Freezing remaining freezable tasks ... (elapsed 0.001 seconds) done.
Suspending console(s) (use no_console_suspend to debug)
Case 21 ...PASS
Case 21 ...PASS
root@linux83-bf609-usbhost:power_ethernet# reset_board 4
powering OFF board attached to printer port pin 4
powering ON board attached to printer port pin 4
Case 22 ...PASS
Case 22 ...PASS
PM: suspend of devices complete after 1.394 msecs
PM: late suspend of devices complete after 0.544 msecs
PM: noirq suspend of devices complete after 0.742 msecs
PM: noirq resume of devices complete after 0.610 msecs
PM: early resume of devices complete after 0.467 msecs
PM: resume of devices complete after 13.897 msecs
Restarting tasks ... done.
root:/>
Case 23 ...PASS
Case 23 ...PASS
stmmaceth stmmaceth.0 eth0: Link is Up - 100Mbps/Full - flow control rx/tx
ifconfig
eth0 Link encap:Ethernet HWaddr 02:80:AD:20:31:E8
inet addr:10.100.4.50 Bcast:10.100.4.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:29 errors:0 dropped:0 overruns:0 frame:0
TX packets:30 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:2690 (2.6 KiB) TX bytes:2660 (2.5 KiB)
Interrupt:75
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:65536 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
root:/>
Case 24 ...PASS
Case 24 ...PASS
ping 10.100.4.174 -c 5
PING 10.100.4.174 (10.100.4.174): 56 data bytes
64 bytes from 10.100.4.174: seq=0 ttl=64 time=1.057 ms
64 bytes from 10.100.4.174: seq=1 ttl=64 time=1.040 ms
64 bytes from 10.100.4.174: seq=2 ttl=64 time=1.023 ms
64 bytes from 10.100.4.174: seq=3 ttl=64 time=1.036 ms
64 bytes from 10.100.4.174: seq=4 ttl=64 time=1.027 ms
--- 10.100.4.174 ping statistics ---
5 packets transmitted, 5 packets received, 0% packet loss
round-trip min/avg/max = 1.023/1.036/1.057 ms
root:/>
Case 24 ...PASS
Case 24 ...PASS
PM test case 1 round 5 pass
ping 10.100.4.174&
[1] 381 ping 10.100.4.174
root:/> PING 10.100.4.174 (10.100.4.174): 56 data bytes
64 bytes from 10.100.4.174: seq=0 ttl=64 time=1.000 ms
64 bytes from 10.100.4.174: seq=1 ttl=64 time=1.036 ms
64 bytes from 10.100.4.174: seq=2 ttl=64 time=1.
Case 25 ...PASS
Case 25 ...PASS
055 ms
echo mem > /sys/power/state
PM: Syncing filesystems ... done.
Freezing user space processes ... (elapsed 0.001 seconds) done.
Freezing remaining freezable tasks ... (elapsed 0.001 seconds) done.
Suspending console(s) (use no_console_suspend to debug)
Case 26 ...PASS
Case 26 ...PASS
root@linux83-bf609-usbhost:power_ethernet# reset_board 4
powering OFF board attached to printer port pin 4
powering ON board attached to printer port pin 4
Case 27 ...PASS
Case 27 ...PASS
PM: suspend of devices complete after 1.398 msecs
PM: late suspend of devices complete after 0.549 msecs
PM: noirq suspend of devices complete after 0.746 msecs
PM: noirq resume of devices complete after 0.551 msecs
PM: early resume of devices complete after 0.471 msecs
PM: resume of devices complete after 13.905 msecs
Restarting tasks ... done.
root:/>
Case 28 ...PASS
Case 28 ...PASS
stmmaceth stmmaceth.0 eth0: Link is Up - 100Mbps/Full - flow control rx/tx
64 bytes from 10.100.4.174: seq=5 ttl=64 time=1.053 ms
64 bytes from 10.100.4.174: seq=6 ttl=64 time=1.057 ms
64 bytes from 10.100.4.174: seq=7 ttl=64 time=1.024 ms
64 bytes from 10.100.4.174: seq=8 ttl=64 time=1.028 ms
64 bytes from 10.100.4.174: seq=9 ttl=64 time=1.039 ms
64 bytes from 10.100.4.174: seq=10 ttl=64 time=1.029 ms
64 bytes from 10.100.4.174: seq=11 ttl=64 time=1.037 ms
64 bytes from 10.100.4.174: seq=12 ttl=64 time=1.027 ms
64 bytes from 10.100.4.174: seq=13 ttl=64 time=1.019 ms
64 bytes from 10.100.4.174: seq=14 ttl=64 time=1.016 ms
64 bytes from 10.100.4.174: seq=15 ttl=64 time=1.035 ms
64 bytes from 10.100.4.174: seq=16 ttl=64 time=1.027 ms
64 bytes from 10.100.4.174: seq=17 ttl=64 time=1.026 ms
64 bytes from 10.100.4.174: seq=18 ttl=64 time=1.123 ms
64 bytes from 10.100.4.174: seq=19 ttl=64 time=1.025 ms
64 bytes from 10.100.4.174: seq=20 ttl=64 time=1.038 ms
64 bytes from 10.100.4.174: seq=21 ttl=64 time=1.018 ms
64 bytes from 10.100.4.174: seq=22 ttl=64 time=1.027 ms
64 bytes from 10.100.4.174: seq=23 ttl=64 time=1.035 ms
64 bytes from 10.100.4.174: seq=24 ttl=64 time=1.019 ms
64 bytes from 10.100.4.174: seq=25 ttl=64 time=1.022 ms
64 bytes from 10.100.4.174: seq=26 ttl=64 time=0.964 ms
64 bytes from 10.100.4.174: seq=27 ttl=64 time=1.020 ms
64 bytes from 10.100.4.174: seq=28 ttl=64 time=0.993 ms
64 bytes from 10.100.4.174: seq=29 ttl=64 time=1.042 ms
64 bytes from 10.100.4.174: seq=30 ttl=64 time=1.008 ms
64 bytes from 10.100.4.174: seq=31 ttl=64 time=1.156 ms
64 bytes from 10.100.4.174: seq=32 ttl=64 time=1.025 ms
64 bytes from 10.100.4.174: seq=33 ttl=64 time=1.035 ms
64 bytesping 10.100.4.174 failed
Last passed time: 2013-12-18_19-27-20
User-dist commit 2e7df81b4985ba6f112742a8e799af05c855fc9a
Kernel commit 31d7b760fc201006e2a6e420a0307d1aeba4b398
Testsuites commit e44f6f0cf84ce8a68b7deccb439de7c6c47526a6
Case 28 ...FAIL
Case 28 ...FAIL
POWER ETHERNET TEST (mem) FAIL
power ethernet can pass on bf609 ezkit now after fixing in code and testscripts.
Booting kernel from Legacy Image at 02000000 ...
Image Name: bf609-0.0-3.16.0-ADI-2014R1-pre-
Image Type: Blackfin Linux Kernel Image (gzip compressed)
Data Size: 7758579 Bytes = 7.4 MiB
Load Address: 00001000
Entry Point: 002fba6c
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Starting Kernel at = 002fba6c
Linux version 3.16.0-ADI-2014R1-pre-00412-ga08e6b6-dirty (test@linux83-bf609-usbhost) (gcc version 4.3.5 (ADI-master/git-46c6a72) ) #4 Tue Sep 9 15:33:05 CST 2014
register early platform devices
bootconsole [early_shadow0] enabled
ERROR: Not running on ADSP-BF609: unknown CPUID 0x0000 Rev 0.0
bootconsole [early_BFuart0] enabled
early printk enabled on early_BFuart0
Board Memory: 128MB
Kernel Managed Memory: 128MB
Memory map:
fixedcode = 0x00000400-0x00000490
text = 0x00001000-0x00205300
rodata = 0x00205324-0x002b27a4
bss = 0x002b3000-0x002cbbc0
data = 0x002cbbc0-0x002f8000
stack = 0x002f6000-0x002f8000
init = 0x002f8000-0x008e5000
available = 0x008e5000-0x07f00000
DMA Zone = 0x07f00000-0x08000000
Hardware Trace active and enabled
Blackfin support (C) 2004-2010 Analog Devices, Inc.
Compiled for ADSP-BF609 Rev 0.0
Blackfin Linux support by http://blackfin.uclinux.org/
Processor Speed: 500 MHz core clock, 125 MHz SCLk, 125 MHz SCLK0, 125 MHz SCLK1 and 250 MHz DCLK
NOMPU: setting up cplb tables
Instruction Cache Enabled for CPU0
External memory: cacheable in instruction cache
L2 SRAM : uncacheable in instruction cache
Data Cache Enabled for CPU0
External memory: cacheable (write-back) in data cache
L2 SRAM : uncacheable in data cache
Built 1 zonelists in Zone order, mobility grouping off. Total pages: 32258
Kernel command line: root=/dev/mtdblock0 rw ip=10.100.4.50 earlyprintk=serial,uart0,57600 console=ttyBF0,57600 ip=10.100.4.50:10.100.4.174:10.100.4.174:255.255.255.0:"bf609-ezkit":eth0:off
PID hash table entries: 512 (order: -1, 2048 bytes)
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 119772K/130048K available (2064K kernel code, 177K rwdata, 693K rodata, 6068K init, 98K bss, 10276K reserved, 1024K DMA)
NR_IRQS:291
Configuring Blackfin Priority Driven Interrupts
Console: colour dummy device 80x25
Calibrating delay loop... 995.32 BogoMIPS (lpj=1990656)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
devtmpfs: initialized
Blackfin Scratchpad data SRAM: 4 KB
Blackfin L1 Data A SRAM: 16 KB (9 KB free)
Blackfin L1 Data B SRAM: 16 KB (16 KB free)
Blackfin L1 Instruction SRAM: 64 KB (49 KB free)
Blackfin L2 SRAM: 256 KB (256 KB free)
pinctrl core: initialized pinctrl subsystem
NET: Registered protocol family 16
Blackfin DMA Controller
ezkit_init(): registering device resources
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
i2c-bfin-twi i2c-bfin-twi.0: Blackfin on-chip I2C TWI Contoller, regs_base@ffc01e00
i2c-bfin-twi i2c-bfin-twi.1: Blackfin on-chip I2C TWI Contoller, regs_base@ffc01f00
pps_core: LinuxPPS API ver. 1 registered
pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti giometti@linux.it
PTP clock support registered
NET: Registered protocol family 23
Switched to clocksource bfin_cs_cycles
NET: Registered protocol family 2
TCP established hash table entries: 1024 (order: 0, 4096 bytes)
TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
TCP: Hash tables configured (established 1024 bind 1024)
TCP: reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
msgmni has been set to 233
io scheduler noop registered (default)
bfin-uart: Blackfin serial driver
bfin-uart.0: ttyBF0 at MMIO 0xffc02000 (irq = 88, base_baud = 7812500) is a BFIN-UART
console [ttyBF0] enabled
console [ttyBF0] enabled
bootconsole [early_BFuart0] disabled
bootconsole [early_BFuart0] disabled
bootconsole [early_shadow0] disabled
physmap platform flash device: 01000000 at b0000000
physmap-flash physmap-flash.0: map_probe failed
m25p80 spi0.59: w25q32 (4096 Kbytes)
Creating 3 MTD partitions on "m25p80":
0x000000000000-0x000000080000 : "bootloader(spi)"
0x000000080000-0x000000200000 : "linux kernel(spi)"
0x000000200000-0x000000400000 : "file system(spi)"
CAN device driver interface
bfin_can bfin_can.0: bfin_can device registered(®_base=ffc00a00, rx_irq=47, tx_irq=48, err_irq=49, sclk=125000000)
stmmaceth stmmaceth.0: no reset control found
stmmac - user ID: 0x10, Synopsys ID: 0x36
Ring mode enabled
DMA HW capability register supported
Enhanced/Alternate descriptors
Enabled extended descriptors
RX Checksum Offload Engine supported (type 2)
Wake-Up On Lan supported
Enable RX Mitigation via HW Watchdog Timer
libphy: stmmac: probed
eth0: PHY ID 20005c90 at 1 IRQ POLL (stmmac-0:01) active
usbcore: registered new interface driver usb-storage
input: bfin-rotary as /devices/platform/bfin-rotary/input/input0
i2c /dev entries driver
bfin_wdt: initialized: timeout=20 sec (nowayout=0)
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
TCP: cubic registered
NET: Registered protocol family 17
can: controller area network core (rev 20120528 abi 9)
NET: Registered protocol family 29
can: raw protocol (rev 20120528)
can: broadcast manager protocol (rev 20120528 t)
can: netlink gateway (rev 20130117) max_hops=1
eth0: device MAC address 02:80:ad:20:31:e8
dma_alloc_init: dma_page @ 0x04fc5000 - 256 pages at 0x07f00000
IP-Config: Complete:
device=eth0, hwaddr=02:80:ad:20:31:e8, ipaddr=10.100.4.50, mask=255.255.255.0, gw=10.100.4.174
host="bf609-ezkit", domain=, nis-domain=(none)
bootserver=10.100.4.174, rootserver=10.100.4.174, rootpath=
Freeing unused kernel memory: 6068K (002f8000 - 008e5000)
BusyBox v1.22.1 (2014-09-09 01:18:38 CST) hush - the humble shell
root:/>successful boot attempt ifconfig ethstmmaceth stmmaceth.0 eth0: Link is Up - 100Mbps/Full - flow control rx/tx
0 10.100.4.50
root:/> Ethernet may has been activated already!
random: nonblocking pool is initialized
version
kernel: Linux release 3.16.0-ADI-2014R1-pre-00412-ga08e6b6-dirty, build #4 Tue Sep 9 15:33:05 CST 2014
toolchain: /home/test/workspace/src/kernel/label/BF609-EZKIT-USBHOST/output/host/usr/bin/bfin-linux-uclibc-gcc release gcc version 4.3.5 (ADI-master/git-46c6a72)
user-dist: release git-426e749, build #2 Tue Sep 9 15:29:55 CST 2014
root:/>
inux version: 3.16.0-ADI-2014R1-pre-00412-ga08e6b6-dirty
GCC version: 4.3.5 (ADI-master/git-46c6a72)
user-dist version: git-426e749
** STEP 3: Start testing
n
root:/> ping 10.100.4.174 -c 5
PING 10.100.4.174 (10.100.4.174): 56 data bytes
64 bytes from 10.100.4.174: seq=0 ttl=64 time=2.013 ms
64 bytes from 10.100.4.174: seq=1 ttl=64 time=1.020 ms
64 bytes from 10.100.4.174: seq=2 ttl=64 time=1.019 ms
64 bytes from 10.100.4.174: seq=3 ttl=64 time=1.029 ms
64 bytes from 10.100.4.174: seq=4 ttl=64 time=1.032 ms
--- 10.100.4.174 ping statistics ---
5 packets transmitted, 5 packets received, 0% packet loss
round-trip min/avg/max = 1.019/1.222/2.013 ms
root:/>
Case 1 ...PASS
Case 1 ...PASS
cat /proc/mounts
rootfs / rootfs rw 0 0
devtmpfs /dev devtmpfs rw,relatime,mode=0755 0 0
proc /proc proc rw,nosuid,nodev,noexec,relatime 0 0
sysfs /sys sysfs rw,nosuid,nodev,noexec,relatime 0 0
mdev /dev tmpfs rw,nosuid,relatime,mode=0755,size=10M 0 0
devpts /dev/pts devpts rw,nosuid,noexec,relatime,mode=600 0 0
var /var tmpfs rw,relatime 0 0
tmp /tmp tmpfs rw,nosuid,nodev,relatime,mode=777 0 0
debugfs /sys/kernel/debug debugfs rw,relatime 0 0
root:/>
Case 2 ...PASS
Case 2 ...PASS
ls /sys/power
pm_async pm_freeze_timeout state wakeup_count
root:/>
ase 3 ...PASS
Case 3 ...PASS
spawn /bin/bash
suites/power_ethernet$ sut:~/workspace/src/kernel/label/BF609-EZKIT-USBHOST/tests
Password:
root@linux83-bf609-usbhost:power_ethernet#
Case 4 ...PASS
Case 4 ...PASS
[6necho mem > /sys/power/state
PM: Syncing filesystems ... done.
Freezing user space processes ... (elapsed 0.012 seconds) done.
Freezing remaining freezable tasks ... (elapsed 0.001 seconds) done.
...
Case 20 ...PASS
PM test case 1 round 4 pass
echo mem > /sys/power/state
PM: Syncing filesystems ... done.
Freezing user space processes ... (elapsed 0.001 seconds) done.
Freezing remaining freezable tasks ... (elapsed 0.001 seconds) done.
Suspending console(s) (use no_console_suspend to debug)
Case 21 ...PASS
Case 21 ...PASS
root@linux83-bf609-usbhost:power_ethernet# reset_board 4
powering OFF board attached to printer port pin 4
powering ON board attached to printer port pin 4
Case 22 ...PASS
Case 22 ...PASS
PM: suspend of devices complete after 1.433 msecs
PM: late suspend of devices complete after 0.569 msecs
PM: noirq suspend of devices complete after 0.766 msecs
PM: noirq resume of devices complete after 0.567 msecs
PM: early resume of devices complete after 0.484 msecs
PM: resume of devices complete after 13.921 msecs
Restarting tasks ... done.
root:/>
Case 23 ...PASS
Case 23 ...PASS
stmmaceth stmmaceth.0 eth0: Link is Up - 100Mbps/Full - flow control rx/tx
ifconfig
eth0 Link encap:Ethernet HWaddr 02:80:AD:20:31:E8
inet addr:10.100.4.50 Bcast:10.100.4.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:29 errors:0 dropped:0 overruns:0 frame:0
TX packets:30 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:2690 (2.6 KiB) TX bytes:2660 (2.5 KiB)
Interrupt:75
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:65536 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
root:/>
Case 24 ...PASS
Case 24 ...PASS
ping 10.100.4.174 -c 5
PING 10.100.4.174 (10.100.4.174): 56 data bytes
64 bytes from 10.100.4.174: seq=0 ttl=64 time=1.061 ms
64 bytes from 10.100.4.174: seq=1 ttl=64 time=1.027 ms
64 bytes from 10.100.4.174: seq=2 ttl=64 time=1.029 ms
64 bytes from 10.100.4.174: seq=3 ttl=64 time=1.033 ms
64 bytes from 10.100.4.174: seq=4 ttl=64 time=1.040 ms
--- 10.100.4.174 ping statistics ---
5 packets transmitted, 5 packets received, 0% packet loss
round-trip min/avg/max = 1.027/1.038/1.061 ms
root:/>
Case 24 ...PASS
Case 24 ...PASS
PM test case 1 round 5 pass
ping 10.100.4.174&
[1] 389 ping 10.100.4.174
root:/> PING 10.100.4.174 (10.100.4.174): 56 data bytes
64 bytes from 10.100.4.174: seq=0 ttl=64 time=1.036 ms
64 bytes from 10.100.4.174: seq=1 ttl=64 time=1.055 ms
64 bytes from 10.100.4.174: seq=2 ttl=64 time=1.
Case 25 ...PASS
Case 25 ...PASS
039 ms
echo mem > /sys/power/state
PM: Syncing filesystems ... done.
Freezing user space processes ... (elapsed 0.001 seconds) done.
Freezing remaining freezable tasks ... (elapsed 0.001 seconds) done.
Suspending console(s) (use no_console_suspend to debug)
Case 26 ...PASS
Case 26 ...PASS
root@linux83-bf609-usbhost:power_ethernet# reset_board 4
powering OFF board attached to printer port pin 4
powering ON board attached to printer port pin 4
Case 27 ...PASS
Case 27 ...PASS
PM: suspend of devices complete after 1.436 msecs
PM: late suspend of devices complete after 0.572 msecs
PM: noirq suspend of devices complete after 0.850 msecs
PM: noirq resume of devices complete after 0.572 msecs
PM: early resume of devices complete after 0.488 msecs
PM: resume of devices complete after 13.918 msecs
Restarting tasks ... done.
root:/>
Case 28 ...PASS
Case 28 ...PASS
stmmaceth stmmaceth.0 eth0: Link is Up - 100Mbps/Full - flow control rx/tx
64 bytes from 10.100.4.174: seq=5 ttl=64 time=1.805 ms
64 bytes from 10.100.4.174: seq=6 ttl=64 time=1.029 ms
64 bytes from 10.100.4.174: seq=7 ttl=64 time=1.026 ms
64 bytes from 10.100.4.174: seq=8 ttl=64 time=1.039 ms
64 bytes from 10.100.4.174: seq=9 ttl=64 time=1.028 ms
64 bytes from 10.100.4.174: seq=10 ttl=64 time=1.017 ms
64 bytes from 10.100.4.174: seq=11 ttl=64 time=1.017 ms
64 bytes from 10.100.4.174: seq=12 ttl=64 time=1.021 ms
64 bytes from 10.100.4.174: seq=13 ttl=64 time=1.033 ms
64 bytes from 10.100.4.174: seq=14 ttl=64 time=1.037 ms
64 bytes from 10.100.4.174: seq=15 ttl=64 time=1.013 ms
64 bytes from 10.100.4.174: seq=16 ttl=64 time=1.021 ms
64 bytes from 10.100.4.174: seq=17 ttl=64 time=0.984 ms
64 bytes from 10.100.4.174: seq=18 ttl=64 time=1.132 ms
64 bytes from 10.100.4.174: seq=19 ttl=64 time=1.020 ms
64 bytes from 10.100.4.174: seq=20 ttl=64 time=1.048 ms
64 bytes from 10.100.4.174: seq=21 ttl=64 time=1.030 ms
64 bytes from 10.100.4.174: seq=22 ttl=64 time=1.037 ms
64 bytes from 10.100.4.174: seq=23 ttl=64 time=1.013 ms
64 bytes from 10.100.4.174: seq=24 ttl=64 time=1.034 ms
64 bytes from 10.100.4.174: seq=25 ttl=64 time=1.027 ms
64 bytes from 10.100.4.174: seq=26 ttl=64 time=0.990 ms
64 bytes from 10.100.4.174: seq=27 ttl=64 time=1.033 ms
64 bytes from 10.100.4.174: seq=28 ttl=64 time=1.019 ms
64 bytes from 10.100.4.174: seq=29 ttl=64 time=1.016 ms
64 bytes from 10.100.4.174: seq=30 ttl=64 time=1.034 ms
64 bytes from 10.100.4.174: seq=31 ttl=64 time=1.143 ms
64 bytes from 10.100.4.174: seq=32 ttl=64 time=1.025 ms
64 bytes from 10.100.4.174: seq=33 ttl=64 time=1.028 ms
64 bytes from 10.100.4.174: seq=34 ttl=64 time=1.010 ms
64 bytes from 10.100.4.174: seq=35 ttl=64 time=1
Case 28 ...PASS
Case 28 ...PASS
PM test case 2 round 1 pass
.029 ms
echo mem > /sys/power/state
PM: Syncing filesystems ... done.
Freezing user space processes ... (elapsed 0.001 seconds) done.
Freezing remaining freezable tasks ... (elapsed 0.001 seconds) done.
Suspending console(s) (use no_console_suspend to debug)
Case 29 ...PASS
Case 29 ...PASS
root@linux83-bf609-usbhost:power_ethernet# reset_board 4
powering OFF board attached to printer port pin 4
powering ON board attached to printer port pin 4
Case 30 ...PASS
Case 30 ...PASS
PM: suspend of devices complete after 1.440 msecs
PM: late suspend of devices complete after 0.577 msecs
PM: noirq suspend of devices complete after 0.855 msecs
PM: noirq resume of devices complete after 0.577 msecs
PM: early resume of devices complete after 0.491 msecs
PM: resume of devices complete after 13.979 msecs
Restarting tasks ... done.
root:/>
Case 31 ...PASS
...
64 bytes from 10.100.4.174: seq=107 ttl=64 time=1.029 ms
64 bytes from 10.100.4.174: seq=108 ttl=64 time=1.037 ms
64 bytes from 10.100.4.174: seq=109 ttl=64 time=1.135 ms
64 bytes from 10.100.4.174: seq=110 ttl=64 time=
Case 37 ...PASS
Case 37 ...PASS
PM test case 2 round 4 pass
1.039 ms
echo mem > /sys/power/state
PM: Syncing filesystems ... done.
Freezing user space processes ... (elapsed 0.001 seconds) done.
Freezing remaining freezable tasks ... (elapsed 0.001 seconds) done.
Suspending console(s) (use no_console_suspend to debug)
Case 38 ...PASS
Case 38 ...PASS
root@linux83-bf609-usbhost:power_ethernet# reset_board 4
powering OFF board attached to printer port pin 4
powering ON board attached to printer port pin 4
Case 39 ...PASS
Case 39 ...PASS
PM: suspend of devices complete after 1.456 msecs
PM: late suspend of devices complete after 0.590 msecs
PM: noirq suspend of devices complete after 0.870 msecs
PM: noirq resume of devices complete after 0.587 msecs
PM: early resume of devices complete after 0.502 msecs
PM: resume of devices complete after 13.918 msecs
Restarting tasks ... done.
root:/>
Case 40 ...PASS
Case 40 ...PASS
stmmaceth stmmaceth.0 eth0: Link is Up - 100Mbps/Full - flow control rx/tx
64 bytes from 10.100.4.174: seq=113 ttl=64 time=1.048 ms
64 bytes from 10.100.4.174: seq=114 ttl=64 time=1.038 ms
64 bytes from 10.100.4.174: seq=115 ttl=64 time=1.024 ms
64 bytes from 10.100.4.174: seq=116 ttl=64 time=1.052 ms
64 bytes from 10.100.4.174: seq=117 ttl=64 time=1.011 ms
64 bytes from 10.100.4.174: seq=118 ttl=64 time=1.030 ms
64 bytes from 10.100.4.174: seq=119 ttl=64 time=1.025 ms
64 bytes from 10.100.4.174: seq=120 ttl=64 time=1.043 ms
64 bytes from 10.100.4.174: seq=121 ttl=64 time=1.033 ms
64 bytes from 10.100.4.174: seq=122 ttl=64 time=1.133 ms
64 bytes from 10.100.4.174: seq=123 ttl=64 time=1.029 ms
64 bytes from 10.100.4.174: seq=124 ttl=64 time=1.033 ms
64 bytes from 10.100.4.174: seq=125 ttl=64 time=1.094 ms
64 bytes from 10.100.4.174: seq=126 ttl=64 time=1.030 ms
64 bytes from 10.100.4.174: seq=127 ttl=64 time=1.014 ms
64 bytes from 10.100.4.174: seq=128 ttl=64 time=1.064 ms
64 bytes from 10.100.4.174: seq=129 ttl=64 time=1.017 ms
64 bytes from 10.100.4.174: seq=130 ttl=64 time=1.038 ms
64 bytes from 10.100.4.174: seq=131 ttl=64 time=1.030 ms
64 bytes from 10.100.4.174: seq=132 ttl=64 time=1.038 ms
64 bytes from 10.100.4.174: seq=133 ttl=64 time=1.025 ms
64 bytes from 10.100.4.174: seq=134 ttl=64 time=1.039 ms
64 bytes from 10.100.4.174: seq=135 ttl=64 time=
Case 40 ...PASS
Case 40 ...PASS
PM test case 2 round 5 pass
Wake up pass
Case 41 ...PASS
Case 41 ...PASS
POWER ETHERNET TEST (mem) ............[PASS]
Test Period is: 380 seconds.
Ending ./power_ethernet_test.exp
close.