#196 adv7393 test fail when install module

[Vivi Li]

adv7393 test fail when install module.

Last passed version:

Last passed time: 2014-02-18_16-39-55
User-dist commit ce7c544a8dc80998e14833beafa606b2437017e7
Kernel commit 4c5762af3f6876efa497a29112555e6a903cbae8
Testsuites commit 7f7bd768548ddc88dc4e12c33eabe5e5531ef206
--

Bellow is the error log:

Linux version 3.15.0-ADI-2014R1-pre-00358-gea73a6a-dirty (test@54-7393-1362-sl811-jtag) (gcc version 4.3.5 (ADI-master/git-a2bfd7b) ) #4 Thu Jul 3 12:21:13 CST 2014
register early platform devices
bootconsole [early_shadow0] enabled
bootconsole [early_BFuart0] enabled
early printk enabled on early_BFuart0
Limiting kernel memory to 56MB due to anomaly 05000263
Board Memory: 64MB
Kernel Managed Memory: 64MB
Memory map:
fixedcode = 0x00000400-0x00000490
text = 0x00001000-0x001726b0
rodata = 0x001726b0-0x001edde8
bss = 0x001ee000-0x00203190
data = 0x002031a0-0x0021e000
stack = 0x0021c000-0x0021e000
init = 0x0021e000-0x00542000
available = 0x00542000-0x03800000
DMA Zone = 0x03f00000-0x04000000
Hardware Trace active and enabled
Boot Mode: 0
Reset caused by Software reset
Blackfin support (C) 2004-2010 Analog Devices, Inc.
Compiled for ADSP-BF537 Rev 0.2
Blackfin Linux support by http://blackfin.uclinux.org/
Processor Speed: 500 MHz core clock and 125 MHz System Clock
NOMPU: setting up cplb tables
Instruction Cache Enabled for CPU0
External memory: cacheable in instruction cache
Data Cache Enabled for CPU0
External memory: cacheable (write-back) in data cache
Built 1 zonelists in Zone order, mobility grouping off. Total pages: 14224
Kernel command line: root=/dev/mtdblock0 rw ip=10.100.4.50 earlyprintk=serial,uart0,57600 console=ttyBF0,57600 ip=10.100.4.50:10.100.4.174:10.100.4.174:255.255.255.0:bf537-stamp:eth0:off
PID hash table entries: 256 (order: -2, 1024 bytes)
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 51352K/57344K available (1477K kernel code, 107K rwdata, 493K rodata, 3216K init, 84K bss, 5992K reserved, 1024K DMA)
NR_IRQS:146
Configuring Blackfin Priority Driven Interrupts
Calibrating delay loop... 995.32 BogoMIPS (lpj=1990656)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
devtmpfs: initialized
Blackfin Scratchpad data SRAM: 4 KB
Blackfin L1 Data A SRAM: 16 KB (16 KB free)
Blackfin L1 Data B SRAM: 16 KB (16 KB free)
Blackfin L1 Instruction SRAM: 48 KB (33 KB free)
NET: Registered protocol family 16
Blackfin DMA Controller
stamp_init(): registering device resources
bfin-spi bfin-spi.0: master is unqueued, this is deprecated
bfin-spi bfin-spi.0: Blackfin on-chip SPI Controller Driver, Version 1.0, regs@ffc00500, dma channel@7
Switched to clocksource bfin_cs_cycles
NET: Registered protocol family 2
TCP established hash table entries: 1024 (order: 0, 4096 bytes)
TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
TCP: Hash tables configured (established 1024 bind 1024)
TCP: reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
debug-mmrs: setting up Blackfin MMR debugfs
msgmni has been set to 100
io scheduler noop registered (default)
bfin-uart: Blackfin serial driver
bfin-uart.0: ttyBF0 at MMIO 0xffc00400 (irq = 18, base_baud = 7812500) is a BFIN-UART
console [ttyBF0] enabled
console [ttyBF0] enabled
bootconsole [early_BFuart0] disabled
bootconsole [early_BFuart0] disabled
bootconsole [early_shadow0] disabled
brd: module loaded
libphy: bfin_mii_bus: probed
bfin_mac: attached PHY driver [Generic PHY] (mii_bus:phy_addr=bfin_mii_bus-0:01, irq=-1, mdc_clk=2500000Hz(mdc_div=24)@sclk=125MHz)
bfin_mac bfin_mac.0 eth0: Blackfin on-chip Ethernet MAC driver, Version 1.1
rtc-bfin rtc-bfin: rtc core: registered rtc-bfin as rtc0
bfin_wdt: initialized: timeout=20 sec (nowayout=0)
TCP: cubic registered
NET: Registered protocol family 17
rtc-bfin rtc-bfin: setting system clock to 1970-01-17 13:16:36 UTC (1430196)
IP-Config: Complete:
device=eth0, hwaddr=00:e0:22:fe:47:c0, ipaddr=10.100.4.50, mask=255.255.255.0, gw=10.100.4.174
host=bf537-stamp, domain=, nis-domain=(none)
bootserver=10.100.4.174, rootserver=10.100.4.174, rootpath=
dma_alloc_init: dma_page @ 0x028f1000 - 256 pages at 0x03f00000
Freeing unused kernel memory: 3216K (0021e000 - 00542000)

BusyBox v1.22.1 (2014-07-02 19:44:08 CST) hush - the humble shell

root:/>successful boot attempt ifconfbfin_mac bfin_mac.0 eth0: Link is Up - 100Mbps/Full - flow control off
ig eth0 10.100.4.50
root:/> Ethernet may has been activated already!
random: nonblocking pool is initialized
version
kernel: Linux release 3.15.0-ADI-2014R1-pre-00358-gea73a6a-dirty, build #4 Thu Jul 3 12:21:13 CST 2014
toolchain: /home/test/workspace/src/kernel/label/BF537-STAMP-ADV7393/output/host/usr/bin/bfin-uclinux-gcc release gcc version 4.3.5 (ADI-master/git-a2bfd7b)
user-dist: release git-809e4dc, build #1 Wed Jul 2 19:51:15 CST 2014
root:/>
Linux version: 3.15.0-ADI-2014R1-pre-00358-gea73a6a-dirty
GCC version: 4.3.5 (ADI-master/git-a2bfd7b)
user-dist version: git-809e4dc

root:/>
** STEP 3: Start testing

modprobe bfin_adv7393fb
i2c-bfin-twi i2c-bfin-twi.0: Blackfin on-chip I2C TWI Contoller, regs_base@ffc01400
bfin-adv7393 0-002b: i2c attach: init error
bfin-adv7393: probe of 0-002b failed with error -1
root:/>
--