Open Source C Simulation Software - Page 6

A curriculum is made to be read by users to improve their skills in a specific topic. In our case we develop on robotics, Webots and the e-puck robot. The documentation can be found here: http://en.wikibooks.org/wiki/Cyberbotics%27_Robot_Curriculum

DSPemu emule a digital signal processor TMS320F243, with console interface showing the registers and memory. With DSPemu is possible test algorithms such as Filter, FFT/IFFT. This can be integrate and used with a circuit simulator.

DSR-UU is an implementation of the Dynamic Source Routing protocol that runs in the Linux kernel or in the ns-2 network simulator. It was originally created at Uppsala University, hence the UU.

A repository of Direct Numerical Simulation codes (Full solutions of the Navier Stokes Equations in fluid dynamics) in various geometries using a mix of high-order finite-difference and spectral methods.

A Disk Scheduling Simulator tool. With an intuitive GUI interface and command line functionality. Built using both VC and VB. Currently supports SSTF,LOOK,CLOOK,SCAN and CSCAN algorithms. Rotational latency is also optionally supported.

DongFeng is a mips simulator which simulates MIPS I ISA and above.

This project introduces a kernel module "dnburstyloss" to enable dummynet emulate bursty packet loss by integrating some common theoretical loss models into Dummynet.

This project enables the introduction of community-based mobility models into the OMNET++ simulation environment. These models provide many desired characteristics, such as socially influenced mobility decisions and are quite realistic. One specific model, namely the Enhanced Community-based mobility model, is very suitable for opportunistic routing research comparing to the others, because of its advanced properties. These include a pause period, conformance to the existing social ties and the ability to produce periodical epochs during the simulation. This is therefore, the main mobility model provided by this project. Up to now, OMNET++ and the INET and INETMANET frameworks do not include an opportunistic routing protocol implementation. Additionally, they lack socially-aware mobility model support, thus making the simulation environment not suitable for opportunistic and delay-tolerant research, especially for Mobile Social Network.

This is a bubble tubes (waterpas) application with a photorealistic EFL-based GUI for handheld devices with accelerometers. It reads data from accelerometers, determines orientation of device and makes moving bubbles in tubes.

All pairs n-body simulation of electromagnetic forces on charged particles, adapted from Nvidia SDK 3.2 sample. Uses Lorentz force from EM fields via the Biot-Savart law for moving charged particles (uses relative velocity). Relativistic.

The backtracking extension to the EPANET hydraulic modeling toolkit

Multinetbot is an adaptation of EasyBot (http://www.easybot.com.ar). It adds the capability to control multiple real bots over a wireless connection, and the possibility of use multiple and different neural networks that are loaded at runtime.

The main purpose of this project is to develop the control software of the digital three phase soft-starter which allows the user to start and stop the motor in an effective way.

A cross-platform simulator for embedded systems, with a plug-in architecture for adding microcontrollers and other devices. Written in C for maximum compatibilty and speed. Currently has support for AVR AT90S8515 and ATmega128.

This project introduces a console application designed for functional and behavioral emulation of the old Soviet calculator EPOS-73 (ЭПОС-73) also known as Elektronika B3-11 (Электроника Б3-11). The project is conceived as an auxiliary for verification of the switch-level simulator based on Verilog HDL of the said apparatus. Calculator model EPOS-73 is interesting in that it was one of the first models of Soviet computing performed at LSI, that were fully designed by Soviet engineers. It was used a set of four LSIs series K1ZHG451...4 (К1ЖГ451...4) or later designation K145HK1...4 (К145ХК1...4). The choice of this calculator as an object of modeling is due to the presence of (miraculously survived to this day) a sufficient set of design documentation for the technology applied in its LSIs, including a technical description of the device, revealing its calculating algorithms. The project is intended for research and education purposes.

Major looseless compression algorithms library and documentation. First project: Arithmetic, Huffman, LZ77, LZ78, LZW, RLE. Second project reimplements Deflate. Documentation explains major Entropy Compression Methods.

A open platform for the design space exploration of a paramerized architecture based on a EPIC/VLIW core. It includes area, power and performance estimators and the implementation of several exploration algorithms presented in literature.

The EvoGrid is an effort to develop a distributed simulation system to simulate potential pre-biotic chemical environments.

We experiment with Evolution of Artifical Neural Networks, combining the two fields of Evolutionary Computation and ANNs. Our methods are applied to a variety of interesting problems. To learn more, click on "Home Page", "Mail", or "Files".

The objective of this project is to implement a fully open source software package to design X-Band antennas similar to the ones developed by NASA fot Space Technology 5 Mission.

Its a model fitting framework which optimizes the model parameters to make the model output match the desired data.

Intend to reproduce most of the conversational programming functionality of the Fagor 8055TC lathe controller. Web browser interface for easy portability between different OS. Visit project web-site for demo.

Fast-DCM (Fast-DynamicCausalModelling) is an open-source addon for the SPM5 toolbox (http://www.fil.ion.ucl.ac.uk/spm/software/spm5/). It accelerates the estimation of Dynamic Causal Models.

A small simulation of an experimental customized Cpu called FlexxCpu. A virtual Cpu whose assembly instructions have been strongly influenced by old cpus architecture (8080, 6809, z80, 68k, etc...) Please support this project by donating to this fundraiser: ------------------------------------------- Give birth to new travel bicycles!!! https://gofund.me/2201d2a4 -------------------------------------------