Search Results for "software auth program"

This program is a lightweight inventory software that allows you to track the number of components in small electronics labs and create order lists for missing or unavailable parts. It is written in Python and runs on PyQt6. Knowing your inventory status before starting a project helps prevent unpleasant surprises. Github: https://github.com/shampuan/StockLab

This program contains many tools for you to perform detailed electronic calculations. Ohms, Kirchhoff, Parralel Res., Voltage Divider, Wheatstone, Reistor Color, Zener diode, LED resistor, capacitor, inductor, transformer, capacitive reactance, Transformerless adaptor, R-C Time calculator, Flip-Flop, NE555 calculator, TL431 calculator, 78XX, LM317, Current Limiter, Transistor Regulator, Current Mirror, Battery charge calculations, transistor calculator, mosfet, pass filters, opamp,...

Program for creating Verilog synthesizable XOR trees for high performance designs. Supports creation of Hamming Code (ECC) generators, checkers, and GF2 Multipliers.

Electronic circuit simulator. Simple environment to run and debug firmware for AVR 8-bit microprocessors. Able to run arduino firmware. Internally this program uses the open source Simavr AVR Processor Simulator (https://github.com/buserror/simavr) and wraps all its functions in a GUI shell. Setups for firmware debugging scenarios can be created dynamically. Able to run 16MHz MCU with decent set of external parts in real time. In particular this can be used for development of CNC firmware...

The Beaglebone Black project presented here is a software written by Python and Qt and is intended to show the simple control of inputs and outputs (GPIO), the graphic course of input signals GPIO, the configuration and sending and receiving of data via the UART interfaces, the display of the PIN configuration of the Beaglebone Black and the graphic display of the signal course at the analog inputs. The software runs on the BBB under Debian 8.9 and on Linux computers (as a demo). It is...

bel_fft is a FFT co-processor that can calculate FFTs with arbitrary radix. It is a hardware implementation of the free software Kiss FFT ("Keep it simple, Stupid!"). The target was to allow a simple replacement of the software code with the hardware implementation. Therefore bel_fft comes with a software driver that is compatible with the Kiss FFT routines. bel_fft also has a modular architecture and allows interfacing different bus architectures. So far AMBA AXI, Altera's Avalon bus and...

This project is a general AVR bootloader, for different type of AVR device, all you need to do is modify macro definition, and you don not need to modify the main program.

JMCAD is an program for the modeling and simulation of complex dynamic systems. This includes the ability to construct and simulate block diagrams. The visual block diagram interface offers a simple method for constructing, modifying and maintaining complex system models. The simulation engine provides fast and accurate solutions for linear, nonlinear, continuous time, discrete time, time varying and hybrid system designs.

It is a software to program ISP based 8051 controllers(89SXX) on Linux. The software decodes the hex file entered from the command line and send it to controller's flash memory using PC's parallel port.The hardware connections are very minimal.

gnuProload is a tool for programming the AT89S52 microcontroller over Linux. Actually it is a Linux port of the 'Proload' and (easy-downloader) software created by Sunrom Technologies which can be used to program AT89S52 microcontrollers.

This project is for converting PCB RS274X gerber files to RS274NGC Gcode files. Currently this software is in the early development stages. Currently working to simplify the program and improve reliability.

ATEProg is project to write software which can program AT89xx and AT89x051 microcontroler chips (and others) in ATE2000 programer (and others).

CircuitSmith is to be a comprehensive electronic design package being developed in Java which will include schematic capture, printed circuit board layout and any other features which I (and hopefully others) can be bothered to program.

GNU PIC LIBRARY PROJECT The interest of this project is to develop a set of Libraries that are released in LGPL License to use to PIC microcontroler programming. Then any program resulted by this use would be a proprietary or free softwares.