[Svxlink-devel] Transmitter stuck on
Brought to you by:
sm0svx
From: Chris W. <n0...@n0...> - 2014-02-24 03:34:47
|
Hello Everyone, I just setup svxlink, and i've been trying it out...I have it hooked into a tx/rx radio pair and everything seems to be working however after the initial keyup the repeater stays keyed up and plays a bell sound every few seconds. I have my repeater setup (isolated) through my serial port RTSDTR/DCD (Active Low), all the signals seem to be fine, COR is detected and PTT works just fine, id's play and audio is repeated...svxlink is just keeping the TX keyed up after COR is dropped... any ideas? I cant seem to find much info out there on this specific issue. below is my svxlink.conf. Thanks! Chris W / N0CSW [GLOBAL] MODULE_PATH=/usr/lib/svxlink LOGICS=RepeaterLogic CFG_DIR=svxlink.d TIMESTAMP_FORMAT="%c" CARD_SAMPLE_RATE=48000 [RepeaterLogic] TYPE=Repeater RX=Rx1 TX=Tx1 MODULES=ModuleHelp,ModuleParrot,ModuleTclVoiceMail CALLSIGN=N0CSW SHORT_IDENT_INTERVAL=10 LONG_IDENT_INTERVAL=60 #IDENT_ONLY_AFTER_TX=4 #EXEC_CMD_ON_SQL_CLOSE=500 EVENT_HANDLER=/usr/share/svxlink/events.tcl DEFAULT_LANG=en_US RGR_SOUND_DELAY=0 REPORT_CTCSS=136.5 #TX_CTCSS=SQL_OPEN MACROS=Macros #SEL5_MACRO_RANGE=03400,03499 FX_GAIN_NORMAL=0 FX_GAIN_LOW=-12 #QSO_RECORDER=8:QsoRecorder #NO_REPEAT=1 IDLE_TIMEOUT=30 #OPEN_ON_1750=1000 #OPEN_ON_CTCSS=136:2000 #OPEN_ON_DTMF=* OPEN_ON_SQL=50 #OPEN_ON_SEL5=01234 #OPEN_SQL_FLANK=OPEN #OPEN_ON_SQL_AFTER_RPT_CLOSE=10 IDLE_SOUND_INTERVAL=3000 #SQL_FLAP_SUP_MIN_TIME=1000 #SQL_FLAP_SUP_MAX_COUNT=10 #ACTIVATE_MODULE_ON_LONG_CMD=4:EchoLink #IDENT_NAG_TIMEOUT=15 #IDENT_NAG_MIN_TIME=2000 #ONLINE_CMD=998877 [Macros] 1=EchoLink:9999# 9=Parrot:0123456789# 03400=EchoLink:9999# [Rx1] TYPE=Local AUDIO_DEV=alsa:plughw:0 AUDIO_CHANNEL=0 SQL_DET=SERIAL SQL_START_DELAY=0 SQL_DELAY=0 SQL_HANGTIME=2000 #SQL_EXTENDED_HANGTIME=1000 #SQL_EXTENDED_HANGTIME_THRESH=15 #SQL_TIMEOUT=600 VOX_FILTER_DEPTH=20 VOX_THRESH=1000 #CTCSS_MODE=2 CTCSS_FQ=136.5 #CTCSS_SNR_OFFSET=0 #CTCSS_OPEN_THRESH=15 #CTCSS_CLOSE_THRESH=9 #CTCSS_BPF_LOW=60 #CTCSS_BPF_HIGH=270 SERIAL_PORT=/dev/ttyS0 SERIAL_PIN=DCD:CLEAR #SERIAL_SET_PINS=DTR!RTS #EVDEV_DEVNAME=/dev/input/by-id/usb-SYNIC_SYNIC_Wireless_Audio-event-if03 #EVDEV_OPEN=1,163,1 #EVDEV_CLOSE=1,163,0 #GPIO_SQL_PIN=gpio30 #SIGLEV_DET=TONE SIGLEV_SLOPE=1 SIGLEV_OFFSET=0 #TONE_SIGLEV_MAP=100,84,60,50,37,32,28,23,19,8 SIGLEV_OPEN_THRESH=30 SIGLEV_CLOSE_THRESH=10 DEEMPHASIS=0 #SQL_TAIL_ELIM=300 #PREAMP=6 PEAK_METER=1 DTMF_DEC_TYPE=INTERNAL DTMF_MUTING=1 DTMF_HANGTIME=100 #DTMF_SERIAL=/dev/ttyS0 #DTMF_MAX_FWD_TWIST=8 #DTMF_MAX_REV_TWIST=4 #1750_MUTING=1 #SEL5_DEC_TYPE=INTERNAL #SEL5_TYPE=ZVEI1 [Tx1] TYPE=Local AUDIO_DEV=alsa:plughw:0 AUDIO_CHANNEL=0 PTT_PORT=/dev/ttyS0 PTT_PIN=DTRRTS #SERIAL_SET_PINS=DTR!RTS PTT_HANGTIME=50 TIMEOUT=300 TX_DELAY=500 #CTCSS_FQ=136.5 #CTCSS_LEVEL=9 PREEMPHASIS=0 DTMF_TONE_LENGTH=100 DTMF_TONE_SPACING=50 DTMF_TONE_AMP=-18 Output from SVXLink: SvxLink v1.3.0 (Feb 23 2014) Copyright (C) 2003-2013 Tobias Blomberg / SM0SVX SvxLink comes with ABSOLUTELY NO WARRANTY. This is free software, and you are welcome to redistribute it in accordance with the terms and conditions in the GNU GPL (General Public License) version 2 or later. Using configuration file: /etc/svxlink/svxlink.conf --- Using sample rate 48000Hz Starting logic: RepeaterLogic Loading RX: Rx1 Loading TX: Tx1 Loading module "ModuleHelp" into logic "RepeaterLogic" Module Help v1.0.0 starting... Loading module "ModuleParrot" into logic "RepeaterLogic" Module Parrot v1.1.0 starting... Loading module "ModuleTclVoiceMail" into logic "RepeaterLogic" Module Tcl v1.0.0 starting... RepeaterLogic: Event handler script successfully loaded. Rx1: The squelch is OPEN (4.98098) Rx1: The squelch is CLOSED (0.766182) Tx1: Turning the transmitter ON *^^^ Transmitter never goes OFF* |