From: Dan C. <dan...@gm...> - 2004-10-11 15:27:50
|
Hello, I have a SAMSUNG SP8004H, can somebody confirm me that the following errors are valid? Thanks, Dan smartctl version 5.30 Copyright (C) 2002-4 Bruce Allen Home page is http://smartmontools.sourceforge.net/ === START OF INFORMATION SECTION === Device Model: SAMSUNG SP8004H Serial Number: 0415J1FT940917 Firmware Version: QW100-60 Device is: In smartctl database [for details use: -P show] ATA Version is: 6 ATA Standard is: ATA/ATAPI-6 T13 1410D revision 1 Local Time is: Mon Oct 11 08:15:17 2004 PDT ==> WARNING: May need -F samsung or -F samsung2 enabled; see manual for details. SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (3600) seconds. Offline data collection capabilities: (0x1b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. No Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. No General Purpose Logging support. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 60) minutes. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000b 097 097 051 Pre-fail Always - 15218 4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 12 5 Reallocated_Sector_Ct 0x0033 253 253 010 Pre-fail Always - 0 7 Seek_Error_Rate 0x000b 253 253 051 Pre-fail Always - 0 8 Seek_Time_Performance 0x0024 253 253 000 Old_age Offline - 0 9 Power_On_Hours 0x0032 099 099 000 Old_age Always - 852183 12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 9 194 Temperature_Celsius 0x0022 169 130 000 Old_age Always - 23 197 Current_Pending_Sector 0x0033 253 253 010 Pre-fail Always - 0 198 Offline_Uncorrectable 0x0031 253 253 010 Pre-fail Offline - 0 199 UDMA_CRC_Error_Count 0x000a 100 100 000 Old_age Always - 0 200 Multi_Zone_Error_Rate 0x000b 100 100 051 Pre-fail Always - 0 201 Soft_Read_Error_Rate 0x000b 100 100 051 Pre-fail Always - 0 SMART Error Log Version: 1 ATA Error Count: 268 (device log contains only the most recent five errors) CR = Command Register [HEX] FR = Features Register [HEX] SC = Sector Count Register [HEX] SN = Sector Number Register [HEX] CL = Cylinder Low Register [HEX] CH = Cylinder High Register [HEX] DH = Device/Head Register [HEX] DC = Device Command Register [HEX] ER = Error register [HEX] ST = Status register [HEX] Timestamp = decimal seconds since the previous disk power-on. Note: timestamp "wraps" after 2^32 msec = 49.710 days. Error 268 occurred at disk power-on lifetime: 48155 hours When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 04 51 00 00 c2 4f e0 Error: ABRT Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Timestamp Command/Feature_Name -- -- -- -- -- -- -- -- --------- -------------------- b0 da 00 00 c2 4f e0 00 2025443.326 SMART RETURN STATUS ec 00 00 b1 2c 14 e0 00 2025443.326 IDENTIFY DEVICE ca 00 08 b1 2c 14 e2 00 3635007.486 WRITE DMA ca 00 08 89 00 16 e2 00 3635007.486 WRITE DMA ca 00 08 19 f8 fd e1 00 3635007.486 WRITE DMA Error 267 occurred at disk power-on lifetime: 48155 hours When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 04 51 00 00 c2 4f e0 Error: ABRT Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Timestamp Command/Feature_Name -- -- -- -- -- -- -- -- --------- -------------------- b0 da 00 00 c2 4f e0 00 2961625.086 SMART RETURN STATUS ec 00 00 b1 2c 14 e0 00 2961625.086 IDENTIFY DEVICE ca 00 08 b1 2c 14 e2 00 3364016.126 WRITE DMA ca 00 08 89 00 16 e2 00 3364016.126 WRITE DMA ca 00 08 a1 f8 fc e1 00 3364016.126 WRITE DMA Error 266 occurred at disk power-on lifetime: 48155 hours When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 04 51 00 00 c2 4f e0 Error: ABRT Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Timestamp Command/Feature_Name -- -- -- -- -- -- -- -- --------- -------------------- b0 da 00 00 c2 4f e0 00 2288242.686 SMART RETURN STATUS ec 00 00 b1 2c 14 e0 00 2288242.686 IDENTIFY DEVICE ca 00 08 b1 2c 14 e2 00 3093024.766 WRITE DMA ca 00 08 89 00 16 e2 00 3093024.766 WRITE DMA ca 00 08 11 f8 fc e1 00 3093024.766 WRITE DMA Error 265 occurred at disk power-on lifetime: 48155 hours When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 04 51 00 00 c2 4f e0 Error: ABRT Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Timestamp Command/Feature_Name -- -- -- -- -- -- -- -- --------- -------------------- b0 da 00 00 c2 4f e0 00 3898199.806 SMART RETURN STATUS ec 00 00 b1 2c 14 e0 00 3898199.806 IDENTIFY DEVICE ca 00 08 b1 2c 14 e2 00 1212862.206 WRITE DMA ca 00 08 89 00 16 e2 00 1212862.206 WRITE DMA ca 00 08 91 f8 f9 e1 00 1212862.206 WRITE DMA Error 264 occurred at disk power-on lifetime: 48155 hours When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 04 51 00 00 c2 4f e0 Error: ABRT Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Timestamp Command/Feature_Name -- -- -- -- -- -- -- -- --------- -------------------- b0 da 00 00 c2 4f e0 00 2953826.046 SMART RETURN STATUS ec 00 00 b1 2c 14 e0 00 2953826.046 IDENTIFY DEVICE ca 00 08 b1 2c 14 e2 00 3356217.086 WRITE DMA ca 00 08 a9 2b e6 e2 00 3356217.086 WRITE DMA ca 00 08 51 08 54 e2 00 3356217.086 WRITE DMA SMART Self-test log structure revision number 1 No self-tests have been logged. [To run self-tests, use: smartctl -t] |