From: Bruce A. <ba...@gr...> - 2002-11-13 21:48:55
|
> I'm using HPT 370 IDE Raid Controller with 2 SMART enabled Hard Drives. I > am using raid-0, should I see errors on the drives due to the raid > controller? As I said in the previous email, it's possible that the 28 ATA errors that are logged were due to some kind of start-up problem with the RAID controller or the drives, early on. Perhaps cabling, or driver misbehavior, or some configuration problem. But it doesn't look like any of the problems occured recently. Does this make sense? Cheers, Bruce > > Here is the output from smartctl > > Drive hde > > smartctl version 5.0-32 Copyright (C) 2002 Bruce Allen > Home page is http://smartmontools.sourceforge.net/ > > === START OF INFORMATION SECTION === > Device Model: Maxtor 4G160J8 > Serial Number: G80D8K4E > Firmware Version: GAK81BK0 > ATA Version is: 6 > ATA Standard is: ATA/ATAPI-6 T13 1410D revision 0 > SMART support is: Available - device has SMART capability. > SMART support is: Enabled > > === START OF READ SMART DATA SECTION === > SMART overall-health self-assessment test result: PASSED > > General SMART Values: > Off-line data collection status: (0x00) Offline data collection > activity was > never started. > Self-test execution status: ( 0) The previous self-test > routine completed > without error or no self-test has > ever > been run. > Total time to complete off-line > data collection: ( 30) seconds. > Offline data collection > capabilities: (0x1b) SMART execute Offline > immediate. > Automatic timer ON/OFF support. > Suspend Offline collection upon new > command. > Offline surface scan supported. > Self-test supported. > SMART capabilities: (0x0003) Saves SMART data before > entering > power-saving mode. > Supports SMART auto save timer. > Error logging capability: (0x01) Error logging supported. > Short self-test routine > recommended polling time: ( 2) minutes. > Extended self-test routine > recommended polling time: ( 103) minutes. > > SMART Attributes Data Structure revision number: 16 > Vendor Specific SMART Attributes with Thresholds: > ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE > WHEN_FAILED RAW_VALUE > 3 Spin_Up_Time 0x0027 197 191 063 Pre-fail - > 9343 > 4 Start_Stop_Count 0x0032 253 253 000 Old_age - > 41 > 5 Reallocated_Sector_Ct 0x0033 253 253 063 Pre-fail - > 0 > 6 Read_Channel_Margin 0x0001 253 253 100 Pre-fail - > 0 > 7 Seek_Error_Rate 0x000a 253 252 000 Old_age - > 0 > 8 Seek_Time_Performance 0x0027 247 239 187 Pre-fail - > 62482 > 9 Power_On_Hours 0x0032 253 253 000 Old_age - > 4855 > 10 Spin_Retry_Count 0x002b 244 239 157 Pre-fail - > 4 > 11 Calibration_Retry_Count 0x002b 253 252 223 Pre-fail - > 0 > 12 Power_Cycle_Count 0x0032 253 253 000 Old_age - > 164 > 192 Power-Off_Retract_Count 0x0032 253 253 000 Old_age - > 0 > 193 Load_Cycle_Count 0x0032 253 253 000 Old_age - > 0 > 194 Temperature_Centigrade 0x0032 253 253 000 Old_age - > 0 > 195 Hardware_ECC_Recovered 0x000a 253 252 000 Old_age - > 573 > 196 Reallocated_Event_Count 0x0008 253 253 000 Old_age - > 0 > 197 Current_Pending_Sector 0x0008 253 253 000 Old_age - > 0 > 198 Offline_Uncorrectable 0x0008 253 253 000 Old_age - > 0 > 199 UDMA_CRC_Error_Count 0x0008 199 199 000 Old_age - > 0 > 200 Unknown_Attribute 0x000a 253 252 000 Old_age - > 0 > 201 Unknown_Attribute 0x000a 253 252 000 Old_age - > 14 > 202 Unknown_Attribute 0x000a 253 252 000 Old_age - > 0 > 203 Unknown_Attribute 0x000b 253 252 180 Pre-fail - > 0 > 204 Unknown_Attribute 0x000a 253 252 000 Old_age - > 0 > 205 Unknown_Attribute 0x000a 253 252 000 Old_age - > 0 > 207 Unknown_Attribute 0x002a 244 239 000 Old_age - > 4 > 208 Unknown_Attribute 0x002a 253 252 000 Old_age - > 0 > 209 Unknown_Attribute 0x0024 253 253 000 Old_age - > 0 > 99 Unknown_Attribute 0x0004 253 253 000 Old_age - > 0 > 100 Unknown_Attribute 0x0004 253 253 000 Old_age - > 0 > 101 Unknown_Attribute 0x0004 253 253 000 Old_age - > 0 > > SMART Error Log Version: 1 > ATA Error Count: 28 (device log contains only the most recent five errors) > DCR = Device Control Register > FR = Features Register > SC = Sector Count Register > SN = Sector Number Register > CL = Cylinder Low Register > CH = Cylinder High Register > D/H = Device/Head Register > CR = Content written to Command Register > ER = Error register > STA = Status register > Timestamp is seconds since the previous disk power-on. > Note: timestamp "wraps" after 2^32 msec = 49.710 days. > > Error 1 occurred at disk power-on lifetime: 0 hours > When the command that caused the error occurred, the device was in an > unknown state. > After command completion occurred, registers were: > ER:04 SC:01 SN:0b CL:4f CH:c2 D/H:e0 ST:51 > Sequence of commands leading to the command that caused the error were: > DCR FR SC SN CL CH D/H CR Timestamp > 08 d1 01 01 4f c2 e0 b0 5829.856 > 08 d0 01 00 4f c2 e0 b0 5829.840 > 08 d1 01 01 4f c2 e0 b0 5827.728 > 08 d0 01 00 4f c2 e0 b0 5827.696 > 08 00 08 00 00 00 e0 c8 5640.768 > > Error 2 occurred at disk power-on lifetime: 0 hours > When the command that caused the error occurred, the device was in an > unknown state. > After command completion occurred, registers were: > ER:04 SC:01 SN:0b CL:4f CH:c2 D/H:e0 ST:51 > Sequence of commands leading to the command that caused the error were: > DCR FR SC SN CL CH D/H CR Timestamp > 08 d0 01 00 4f c2 e0 b0 5829.840 > 08 d1 01 01 4f c2 e0 b0 5827.728 > 08 d0 01 00 4f c2 e0 b0 5827.696 > 08 00 08 00 00 00 e0 c8 5640.768 > 08 00 08 08 00 00 e0 c8 5640.768 > > Error 3 occurred at disk power-on lifetime: 0 hours > When the command that caused the error occurred, the device was in an > unknown state. > After command completion occurred, registers were: > ER:04 SC:01 SN:0b CL:4f CH:c2 D/H:e0 ST:51 > Sequence of commands leading to the command that caused the error were: > DCR FR SC SN CL CH D/H CR Timestamp > 08 d1 01 01 4f c2 e0 b0 5827.728 > 08 d0 01 00 4f c2 e0 b0 5827.696 > 08 00 08 00 00 00 e0 c8 5640.768 > 08 00 08 08 00 00 e0 c8 5640.768 > 08 00 08 00 00 00 e0 c8 5640.736 > > Error 4 occurred at disk power-on lifetime: 0 hours > When the command that caused the error occurred, the device was in an > unknown state. > After command completion occurred, registers were: > ER:04 SC:01 SN:0b CL:4f CH:c2 D/H:e0 ST:51 > Sequence of commands leading to the command that caused the error were: > DCR FR SC SN CL CH D/H CR Timestamp > 08 d0 01 00 4f c2 e0 b0 5827.696 > 08 00 08 00 00 00 e0 c8 5640.768 > 08 00 08 08 00 00 e0 c8 5640.768 > 08 00 08 00 00 00 e0 c8 5640.736 > 08 03 10 00 00 00 e0 c6 5640.736 > > Error 5 occurred at disk power-on lifetime: 43 hours > When the command that caused the error occurred, the device was in an > unknown state. > After command completion occurred, registers were: > ER:04 SC:01 SN:0b CL:4f CH:c2 D/H:e0 ST:51 > Sequence of commands leading to the command that caused the error were: > DCR FR SC SN CL CH D/H CR Timestamp > 08 d1 01 01 4f c2 e0 b0 184149.776 > 08 d0 01 00 4f c2 e0 b0 184149.744 > 08 d1 01 01 4f c2 e0 b0 182126.240 > 08 d0 01 00 4f c2 e0 b0 182126.208 > 08 d1 01 01 4f c2 e0 b0 180233.776 > > SMART Self-test log, version number 1 > No self-tests have been logged > > Drive hdg > > smartctl version 5.0-32 Copyright (C) 2002 Bruce Allen > Home page is http://smartmontools.sourceforge.net/ > > === START OF INFORMATION SECTION === > Device Model: Maxtor 4G160J8 > Serial Number: G8000000 > Firmware Version: GAK819K0 > ATA Version is: 6 > ATA Standard is: ATA/ATAPI-6 T13 1410D revision 0 > SMART support is: Available - device has SMART capability. > SMART support is: Enabled > > === START OF READ SMART DATA SECTION === > SMART overall-health self-assessment test result: PASSED > > General SMART Values: > Off-line data collection status: (0x00) Offline data collection > activity was > never started. > Self-test execution status: ( 0) The previous self-test > routine completed > without error or no self-test has > ever > been run. > Total time to complete off-line > data collection: ( 30) seconds. > Offline data collection > capabilities: (0x1b) SMART execute Offline > immediate. > Automatic timer ON/OFF support. > Suspend Offline collection upon new > command. > Offline surface scan supported. > Self-test supported. > SMART capabilities: (0x0003) Saves SMART data before > entering > power-saving mode. > Supports SMART auto save timer. > Error logging capability: (0x01) Error logging supported. > Short self-test routine > recommended polling time: ( 2) minutes. > Extended self-test routine > recommended polling time: ( 103) minutes. > > SMART Attributes Data Structure revision number: 16 > Vendor Specific SMART Attributes with Thresholds: > ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE > WHEN_FAILED RAW_VALUE > 3 Spin_Up_Time 0x0027 209 208 063 Pre-fail - > 15365 > 4 Start_Stop_Count 0x0032 253 253 000 Old_age - > 87 > 5 Reallocated_Sector_Ct 0x0033 253 253 063 Pre-fail - > 0 > 6 Read_Channel_Margin 0x0001 253 253 100 Pre-fail - > 0 > 7 Seek_Error_Rate 0x000a 253 252 000 Old_age - > 0 > 8 Seek_Time_Performance 0x0027 246 239 187 Pre-fail - > 37461 > 9 Power_On_Hours 0x0032 253 253 000 Old_age - > 11819 > 10 Spin_Retry_Count 0x002b 253 252 223 Pre-fail - > 0 > 11 Calibration_Retry_Count 0x002b 253 252 223 Pre-fail - > 0 > 12 Power_Cycle_Count 0x0032 253 253 000 Old_age - > 255 > 192 Power-Off_Retract_Count 0x0032 253 253 000 Old_age - > 0 > 193 Load_Cycle_Count 0x0032 253 253 000 Old_age - > 0 > 194 Temperature_Centigrade 0x0032 253 253 000 Old_age - > 0 > 195 Hardware_ECC_Recovered 0x000a 253 252 000 Old_age - > 16 > 196 Reallocated_Event_Count 0x0008 253 253 000 Old_age - > 0 > 197 Current_Pending_Sector 0x0008 253 253 000 Old_age - > 0 > 198 Offline_Uncorrectable 0x0008 253 253 000 Old_age - > 0 > 199 UDMA_CRC_Error_Count 0x0008 192 142 000 Old_age - > 56 > 200 Unknown_Attribute 0x000a 253 252 000 Old_age - > 0 > 201 Unknown_Attribute 0x000a 253 252 000 Old_age - > 2 > 202 Unknown_Attribute 0x000a 253 252 000 Old_age - > 0 > 203 Unknown_Attribute 0x000b 253 252 180 Pre-fail - > 0 > 204 Unknown_Attribute 0x000a 253 252 000 Old_age - > 0 > 205 Unknown_Attribute 0x000a 253 252 000 Old_age - > 0 > 207 Unknown_Attribute 0x002a 253 252 000 Old_age - > 0 > 208 Unknown_Attribute 0x002a 253 252 000 Old_age - > 0 > 209 Unknown_Attribute 0x0024 253 253 000 Old_age - > 0 > 99 Unknown_Attribute 0x0004 253 253 000 Old_age - > 0 > 100 Unknown_Attribute 0x0004 253 253 000 Old_age - > 0 > 101 Unknown_Attribute 0x0004 253 253 000 Old_age - > 0 > > SMART Error Log Version: 1 > No Errors Logged > > SMART Self-test log, version number 1 > Num Test_Description Status Remaining LifeTime(hours) > LBA_of_first_error > # 1 Short off-line Completed 00% 0 > > > > > > > ------------------------------------------------------- > This sf.net email is sponsored by: Are you worried about > your web server security? Click here for a FREE Thawte > Apache SSL Guide and answer your Apache SSL security > needs: http://www.gothawte.com/rd523.html > _______________________________________________ > Smartmontools-support mailing list > Sma...@li... > https://lists.sourceforge.net/lists/listinfo/smartmontools-support > |