From: Timo H. <tim...@ip...> - 2009-01-21 13:43:01
|
hi list, this is the output of my maxtor drive. ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 3 Spin_Up_Time 0x0027 252 252 063 Pre-fail Always - 1030 4 Start_Stop_Count 0x0032 253 253 000 Old_age Always - 8 5 Reallocated_Sector_Ct 0x0033 253 253 063 Pre-fail Always - 0 6 Read_Channel_Margin 0x0001 253 253 100 Pre-fail Offline - 0 7 Seek_Error_Rate 0x000a 253 252 000 Old_age Always - 0 8 Seek_Time_Performance 0x0027 247 240 187 Pre-fail Always - 42141 9 Power_On_Minutes 0x0032 240 240 000 Old_age Always - 342h+03m 10 Spin_Retry_Count 0x002b 252 252 157 Pre-fail Always - 0 11 Calibration_Retry_Count 0x002b 252 252 223 Pre-fail Always - 0 12 Power_Cycle_Count 0x0032 253 253 000 Old_age Always - 23 192 Power-Off_Retract_Count 0x0032 253 253 000 Old_age Always - 4 193 Load_Cycle_Count 0x0032 253 253 000 Old_age Always - 29 194 Temperature_Celsius 0x0032 253 253 000 Old_age Always - 26 195 Hardware_ECC_Recovered 0x000a 253 252 000 Old_age Always - 3833 196 Reallocated_Event_Count 0x0008 253 253 000 Old_age Offline - 0 197 Current_Pending_Sector 0x0008 253 253 000 Old_age Offline - 0 198 Offline_Uncorrectable 0x0008 253 253 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x0008 199 199 000 Old_age Offline - 0 200 Multi_Zone_Error_Rate 0x000a 253 252 000 Old_age Always - 0 201 Soft_Read_Error_Rate 0x000a 253 251 000 Old_age Always - 253 202 TA_Increase_Count 0x000a 253 252 000 Old_age Always - 0 203 Run_Out_Cancel 0x000b 253 252 180 Pre-fail Always - 3 204 Shock_Count_Write_Opern 0x000a 253 252 000 Old_age Always - 0 205 Shock_Rate_Write_Opern 0x000a 253 252 000 Old_age Always - 0 207 Spin_High_Current 0x002a 252 252 000 Old_age Always - 0 208 Spin_Buzz 0x002a 252 252 000 Old_age Always - 0 209 Offline_Seek_Performnce 0x0024 253 253 000 Old_age Offline - 0 99 Unknown_Attribute 0x0004 253 253 000 Old_age Offline - 0 100 Unknown_Attribute 0x0004 253 253 000 Old_age Offline - 0 101 Unknown_Attribute 0x0004 253 253 000 Old_age Offline - 0 i think i know the difference between normalized and raw values, but why are most normalized values displayed as 253? additional info: Drive found in smartmontools Database. Drive identity strings: MODEL: Maxtor 6E040L0 FIRMWARE: NAR61590 match smartmontools Drive Database entry: MODEL REGEXP: ^Maxtor 6E0[234]0L0$ FIRMWARE REGEXP: .* MODEL FAMILY: Maxtor DiamondMax Plus 8 family ATTRIBUTE OPTIONS: 009 Power_On_Minutes smartmontools release 5.36 dated 2006/04/12 at 17:39:01 UTC smartmontools build host: i686-pc-linux-gnu smartmontools build configured: 2006/09/29 13:50:35 UTC smartctl compile dated Sep 29 2006 at 13:50:50 smartmontools configure arguments: '--prefix=/usr' '--sysconfdir=/etc' '--mandir=/usr/share/man' '--with-initscriptdir=/etc/init.d' '--with-docdir=/usr/share/doc/smartmontools' 'CFLAGS=-fsigned-char -Wall -O2' Thanks for your help, Timo |