From: <adr...@us...> - 2011-04-21 20:55:20
|
Revision: 4104 http://reprap.svn.sourceforge.net/reprap/?rev=4104&view=rev Author: adrian-bowyer Date: 2011-04-21 20:55:14 +0000 (Thu, 21 Apr 2011) Log Message: ----------- Huxley extruder design. WIP. Modified Paths: -------------- trunk/huxley/OpenSCAD-huxley/parameters.scad trunk/huxley/OpenSCAD-huxley/universal-1.75mm-filament-extruder.scad Modified: trunk/huxley/OpenSCAD-huxley/parameters.scad =================================================================== --- trunk/huxley/OpenSCAD-huxley/parameters.scad 2011-04-21 15:15:52 UTC (rev 4103) +++ trunk/huxley/OpenSCAD-huxley/parameters.scad 2011-04-21 20:55:14 UTC (rev 4104) @@ -2,7 +2,7 @@ // Set ONE OF these true. -huxley=true; +huxley=false; mendel=!huxley; Modified: trunk/huxley/OpenSCAD-huxley/universal-1.75mm-filament-extruder.scad =================================================================== --- trunk/huxley/OpenSCAD-huxley/universal-1.75mm-filament-extruder.scad 2011-04-21 15:15:52 UTC (rev 4103) +++ trunk/huxley/OpenSCAD-huxley/universal-1.75mm-filament-extruder.scad 2011-04-21 20:55:14 UTC (rev 4104) @@ -43,7 +43,7 @@ motor_position=[-motor_radius*cos(motor_angle), 1, motor_radius*sin(motor_angle)]; fixed_block_position=[0,0,10]; -duct_offset=[-5.5,0,10]; +duct_offset=[-5.5,0,7]; base_position=[0,0,-3]; clamp_position=[-12, -44, -9]; drive_assembly_position=[hub_x,filament_y_offset,hub_z]; @@ -539,8 +539,10 @@ { difference() { - cube([45,20,50],center=true); - cube([41,16,46],center=true); + translate([0,0,1]) + cube([45,20,52],center=true); + translate([0,0,1]) + cube([41,16,48],center=true); translate(fixed_block_position-duct_offset) nozzle_holes(teardrop_angle=180); translate([10,0,9]) @@ -703,15 +705,10 @@ translate([24.5,0,10]) difference() { - translate([-2+(fan_thickness-7)/2,0,-4]) - cube([9+fan_thickness-7,20,17], center = true); - translate([-7+fan_thickness-7,0,4]) - cube([14,30,8], center = true); - translate([-10+(fan_thickness-7)/2,0,1.5]) - cube([16+fan_thickness-7,30,18], center = true); - translate([fan_thickness-7, 0, 4.5/sin(45)]) - rotate([0,45,0]) - cube([9,30,9], center = true); + translate([-4.5,0,-4.5]) + cube([6,20,16], center = true); + translate([-11,0,-2]) + cube([14,30,12], center = true); } } } @@ -899,33 +896,33 @@ translate(duct_offset) duct(); -translate(base_position) +translate(base_position+[0,0,-3.2]) base_plate(); if(huxley) translate(clamp_position) belt_clamp(); -//translate(motor_plate_position) -// motor_plate(); +translate(motor_plate_position) + motor_plate(); -//translate(motor_plate_clip_position) -// motor_plate_clip(); +translate(motor_plate_clip_position) + motor_plate_clip(); -//translate(spacer_position) -// motor_spacer(); +translate(spacer_position) + motor_spacer(); -//translate(lever_offset) -// lever(); +translate(lever_offset) + lever(); -//translate(drive_assembly_position) -// drive_assembly(); +translate(drive_assembly_position) + drive_assembly(); -//translate(fan_position) -// fan(); +translate(fan_position) + fan(); -//translate(accessories_position) -// accessories(); +translate(accessories_position) + accessories(); //----------------------------------------------------------------- This was sent by the SourceForge.net collaborative development platform, the world's largest Open Source development site. |