Re: [munin-users] Received values not recorded in graph was Re: apc_nis

[Bjørn R. <bj...@ru...>]

On 17. feb. 2015 14:33, BERTRAND Joël wrote:
> BERTRAND Joël a écrit :
>> Bjørn Ruberg a écrit :
>>> munin-run apc_nis config
>> 	I obtain :
>>
>> bash-4.3# munin-run apc_nis config
>> graph_title apcupsd
>> graph_args -l 0 --base 1000
>> graph_vlabel A bit of all (Volt, time, %)
>> battery_volt.label batt volt (V)
>> battery_volt.type GAUGE
>> battery_volt.max 140
>> battery_charge.label batt charge (%)
>> battery_charge.type GAUGE
>> battery_charge.max 200
>> line_volt.label line (V)
>> line_volt.type GAUGE
>> line_volt.max 200
>> load.label ups load (%)
>> load.type GAUGE
>> load.max 200
>> time_left.label time left (min)
>> time_left.type GAUGE
>> time_left.max 200
>>
>> 	But I don't undestand as munin-run apc_nis returns correct values.
> 	Some news. When I try to access to munin-node from server, all values
> are sent without error :
>
> rayleigh:[~] > telnet legendre 4949
> Trying 192.168.1.2...
> Connected to legendre.systella.fr.
> Escape character is '^]'.
> # munin node at legendre.systella.fr
> fetch apc_nis
> line_volt.value 238.0
> load.value 70.0
> battery_charge.value 100.0
> time_left.value 8.2
> battery_volt.value 27.6
> .
> quit
> Connection closed by foreign host.
>
> 	All but line_volt.value values are present in graphs.

Did you not read my last response?

> I have written a
> new plugin to parse smartctl output (on sparc64/NetBSD). If I test this
> plugin, I obtain :
>
> rayleigh:[~] > telnet legendre 4949
> Trying 192.168.1.2...
> Connected to legendre.systella.fr.
> Escape character is '^]'.
> # munin node at legendre.systella.fr
> fetch smart_rsd4c
> write_rereads.value 0
> write_ECC_fast.value 0
> read_processed_GB.value 1356.234
> write_processed_GB.value 743.001
> Current_Drive_Temperature.value 15
> read_ECC_delayed.value 0
> read_invocation.value 0
> Accumulated_start-stop_cycles.value   33
> write_invocation.value 0
> read_ECC_fast.value 0
> Drive_Trip_Temperature.value 65
> Non-medium_error_count.value       188
> read_corrected.value 0
> Elements_in_grown_defect_list.value  0
> read_rereads.value 0
> write_ECC_delayed.value 0
> smartctl_exit_status.value 0
> write_corrected.value 0
> SMART_Health_Status.value 0
> Specified_cycle_count_over_device_lifetime.value   10000
> .
> quit
> Connection closed by foreign host.
>
> but only Accumulated_start-stop_cycles.value is written in graphs. I
> suppose I have done a mistake... Any idea ?

Not until you show the output from the config run.

In a telnet session: config smart_rsd4c
As root on the munin-node: munin-run smart_rsd4c config

You should also show an example of your graph. Are the fieldnames 
mentioned in the graph legend? Since a lot of values are "0", those can 
be hard to see in the graph itself.

-- 
Bjørn