From: Pete C <ha...@th...> - 2009-04-18 01:44:43
|
Gregg Liming wrote: > Pete C wrote: >> >> .. and nothing in the mh log .. > > I wasn't paying attention to this part of your prior response. If you > did set debug=xap;bsc and you don't see anything in the mh log when you > manually change status on the device, then you definitely do not have a > hub properly working w/ mh. You should see xap traffic echoed in the mh > log. So, a far more fundamental problem exists w/ your setup. > so, I tried a different xAP hub (was using xapmcsHUB (same guy that wrote the AdiOcelot xAP app, which gives me a uneasy feeling) and switched to xFx-Express Hub) now I am getting xAP messages echoed in mh log .. I restarted everything .. xAP hub first .. and it's log shows .. 17-Apr-09 21:14:05.9 INFO Initialising xFx-Express Hub on command line 17-Apr-09 21:14:05.9 INFO Hit Return to exit 17-Apr-09 21:14:06.2 INFO Starting... 17-Apr-09 21:14:06.2 INFO xFx.Hub.Commando UID=FF.0535BEC1:0000 (v13) 17-Apr-09 21:14:06.5 INFO Selected Ethernet network interface 'Local Area Conne ction 2' Intel(R) PRO/1000 MT Network Connection - Packet Scheduler Miniport 17-Apr-09 21:14:06.5 INFO Transmit to: 10.0.2.255:3639 17-Apr-09 21:14:06.5 INFO Listening on: 10.0.2.10:3639 17-Apr-09 21:14:06.5 INFO Starting hub heartbeat, interval 60 seconds 17-Apr-09 21:15:12.6 INFO Register mhouse.mh.misterhouse.core on port 49152, ti meout 21:17:12 17-Apr-09 21:15:16.2 INFO Register mhouse.mh.misterhouse.x10_device on port 491 53, timeout 21:17:16 17-Apr-09 21:15:16.2 INFO Register mhouse.mh.misterhouse.abstract_device on por t 49154, timeout 21:17:16 17-Apr-09 21:15:16.2 INFO Register mhouse.mh.misterhouse.presence on port 49155 , timeout 21:17:16 17-Apr-09 21:15:35.7 INFO Register mcs.AdiOcelot.COMMANDO on port 32768, timeou t 21:35:35 .. then in th mh log when I hit the RF button .. In $bsc_x10_device set callback for $rf_button_a9 using x10_device No state change for $rf_button_a9 [BSC] $adi_sec_mode extracting subaddress uid = db1 xap check: p=xAP s=mhouse.mh.misterhouse.core c=xapbsc.cmd t=mcs.adiocelot.c ommando:> d=xap-header { v=12 hop=1 uid=FFE90000 source=mhouse.mh.misterhouse.core class=xapbsc.cmd target=mcs.AdiOcelot.COMMANDO:> } output.state.1 { level=1/32767 state=on } .. then this repeats 4 times .. (most xAP msgs seem to go by 4 times in the mh log) .. db1 xap check: p=xAP s=mhouse.mh.misterhouse.core c=xapbsc.cmd t=mcs.adiocelot.c ommando:> d=xap-header { v=12 hop=1 uid=FFE90000 source=mhouse.mh.misterhouse.core class=xapbsc.cmd target=mcs.AdiOcelot.COMMANDO:> } output.state.1 { level=1/32767 state=on } .. this when I change the value at the device .. db1 xap check: p=xAP s=mcs.adiocelot.commando:ocelot_securitymode.ocelot_var__v0 10.index c=xapbsc.event t= d=xap-header { v=13 hop=1 uid=FF.00C7:0B class=xapBSC.Event source=mcs.AdiOcelot.COMMANDO:Ocelot_SecurityMode.Ocelot_Var__V010.Index } output.state { State=ON Level=1/32767 } db BSC_Item->event_callback: Process section:output.state from mcs.adiocelot.com mando:ocelot_securitymode.ocelot_var__v010.index db1 xap check: p=xAP s=mcs.adiocelot.commando:ocelot_securitymode.ocelot_var__v0 10.index c=xapbsc.event t= d=xap-header { v=13 hop=1 uid=FF.00C7:0B class=xapBSC.Event source=mcs.AdiOcelot.COMMANDO:Ocelot_SecurityMode.Ocelot_Var__V010.Index } output.state { State=ON Level=1/32767 } .. and this repeats 4 times .. db1 xap check: p=xAP s=mcs.adiocelot.commando:ocelot_securitymode.ocelot_var__v0 10.index c=xapbsc.event t= d=xap-header { v=13 hop=1 uid=FF.00C7:0B class=xapBSC.Event source=mcs.AdiOcelot.COMMANDO:Ocelot_SecurityMode.Ocelot_Var__V010.Index } output.state { State=ON Level=1/32767 } .. any thoughts on what is going wrong? |