Re: [Madwifi-devel] Cross compiling madwifi

[Vishal S. <vis...@gm...>]

On Sun, Apr 4, 2010 at 2:23 AM, Dino Joseph Mycle <din...@ya...>wrote:

> hi,
>   please check if you are using ar71xx hal from the openwrt for the ar71xx
> processor to make to work with ar5xxx chipsets.
>

Do you mean hal of madwifi?? Iam defining the target to be,
TARGET="mips32r2-be-elf" as an option to make command (openwrt make also
does the same thing), and I have copied the hal binaries for compiling for
that available along with openwrt source code. Even then it is giving the
same error.

Thanks
Vishal

>
> Regards,
> Dino Joseph Mycle
>
>
> ------------------------------
> *From:* Vishal Sevani <vis...@gm...>
> *To:* mad...@li...
> *Sent:* Sat, 3 April, 2010 4:12:16 PM
> *Subject:* [Madwifi-devel] Cross compiling madwifi
>
> Hi
>
> Iam running madwifi drivers on openwrt kamikaze 8.09 on ar71xx based
> Mikrotik RB433AH based boards. If I compile the madwifi driver along with
> the kernel it works fine. However if cross compile the driver with the
> following options
>
> COPTS="-DCONFIG_ATHEROS_RATE_DEFAULT='\"minstrel\"'
> -DATH_REVERSE_ENGINEERING=1"  make -C
> /home/vsevani/Research/long_distance_wireless/fractel/code/madwifi-trunk-r3314
> PATH="/home/vsevani/openwrt/kamikaze_8.09/staging_dir/toolchain-mips_gcc4.1.2/bin:/home/vsevani/openwrt/kamikaze_8.09/staging_dir/host/bin:/home/vsevani/openwrt/kamikaze_8.09/staging_dir/mips/host/bin:/home/vsevani/openwrt/kamikaze_8.09/staging_dir/toolchain-mips_gcc4.1.2/bin:/home/vsevani/openwrt/kamikaze_8.09/staging_dir/host/bin:/home/vsevani/openwrt/kamikaze_8.09/staging_dir/mips/host/bin:/home/vsevani/openwrt/kamikaze_8.09/staging_dir/toolchain-mips_gcc4.1.2/bin:/home/vsevani/openwrt/kamikaze_8.09/staging_dir/host/bin:/home/vsevani/openwrt/kamikaze_8.09/staging_dir/mips/host/bin:/usr/local/sbin:/usr/local/bin:/usr/sbin:/usr/bin:/sbin:/bin:/usr/X11R6/bin"
> ARCH="mips" CROSS_COMPILE="mips-linux-uclibc-" TARGET="mips32r2-be-elf"
> TOOLPREFIX="mips-linux-uclibc-" TOOLPATH="mips-linux-uclibc-"
> KERNELPATH="/home/vsevani/openwrt/kamikaze_8.09/build_dir/linux-ar71xx/linux-2.6.26.5"
> LDOPTS="--no-warn-mismatch " ATH_RATE="ath_rate/minstrel" DO_MULTI=1 DEBUG=
> WARNINGS="-Wno-unused" BUS="PCI" modules
>
> The compilation goes fine, however on loading the modules I get the
> following error
>
> PCI error 1 at PCI addr 0x10004000
> Data bus error, epc == c0162384, ra == c0163850
>
> Any clues as to what I could be doing wrong??
>
> Thanks
> Vishal
>
> ------------------------------
> Your Mail works best with the New Yahoo Optimized IE8. Get it NOW!<http://in.rd.yahoo.com/tagline_ie8_new/*http://downloads.yahoo.com/in/internetexplorer/>
> .
>