[Madwifi-users] Re: Cisco VPN sw client problems

[Nate P. <np...@sg...>]

Here is the dmesg info pertinent to madwifi:

ath_hal: module not supported by Novell, setting U taint flag.
ath_hal: module license 'Proprietary' taints kernel.
ath_hal: 0.9.16.16 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413,
RF5413)
wlan: module not supported by Novell, setting U taint flag.
wlan: 0.8.4.2 (svn 1560)
ath_rate_sample: module not supported by Novell, setting U taint flag.
ath_rate_sample: 1.2 (svn 1560)
ath_pci: module not supported by Novell, setting U taint flag.
ath_pci: 0.9.4.5 (svn 1560)
PCI: Enabling device 0000:06:00.0 (0000 -> 0002)
ACPI: PCI Interrupt 0000:06:00.0[A] -> Link [LNKD] -> GSI 11 (level,
low) -> IRQ 11
wifi0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps
wifi0: 11g rates: 1Mbps 2Mbps 5.5Mbps 11Mbps 6Mbps 9Mbps 12Mbps 18Mbps
24Mbps 36Mbps 48Mbps 54Mbps
wifi0: turboG rates: 6Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
wifi0: H/W encryption support: WEP AES AES_CCM TKIP
wifi0: mac 5.9 phy 4.3 radio 4.6
wifi0: Use hw queue 1 for WME_AC_BE traffic
wifi0: Use hw queue 0 for WME_AC_BK traffic
wifi0: Use hw queue 2 for WME_AC_VI traffic
wifi0: Use hw queue 3 for WME_AC_VO traffic
wifi0: Use hw queue 8 for CAB traffic
wifi0: Use hw queue 9 for beacons
cs: IO port probe 0x100-0x3af: excluding 0x170-0x177 0x370-0x37f
cs: IO port probe 0x3e0-0x4ff: clean.
wlan_scan_sta: module not supported by Novell, setting U taint flag.
cs: IO port probe 0x820-0x8ff: clean.
cs: IO port probe 0xc00-0xcf7: clean.
wifi0: Atheros 5212: mem=0x26000000, irq=11
cs: IO port probe 0xa00-0xaff: clean.
cs: IO port probe 0x100-0x3af: excluding 0x170-0x177 0x370-0x37f
cs: IO port probe 0x3e0-0x4ff: clean.
cs: IO port probe 0x820-0x8ff: clean.
cs: IO port probe 0xc00-0xcf7: clean.
cs: IO port probe 0xa00-0xaff: clean.




On Thu, 2006-05-25 at 13:01 -0400, Nate Pearlstein wrote:
> Running SuSE Linux 10.1 2.6.16.13-4-default
> 
> Have rpms from 5/19 from http://madwifi.org/suse
> 
> madwifi-1560-0.1
> madwifi-kmp-default-1560_2.6.16.13_4-0.1
> 
> Cisco Systems VPN Client Version 4.8.00 (0490)
> 
> 
> I know the vpn parts work okay with my linksys wired pcmcis etherenet
> card.  The newer version of the client is required to work with Linux
> kernels greater than or equal 2.6.14.
> 
> 
> I can authenticate to the vpn when using ath0 and it send me data for
> resolv.conf etc.  However When I do simple things like DNS lookups or
> telnets I see the outgoing packets on the cipsec0 interface using
> tethereal but never any responses.
> 
> I read the wiki section, "How do I get the Cisco VPN client to work
> with madwifi?"  http://madwifi.org/wiki/UserDocs/FixCiscoVpnClient
> 
> I tried the second suggestion even though I do not see receive frame
> errors.
> 
> I'm not sure how to go about debugging this or if its a known problem.
> I will look for help here before opening a ticket.
> 
> Thanks!
> 
> Later
-- 
===========================================================
            Its a Smallworld is in Fantasyland
===========================================================
Nate Pearlstein - np...@sg... - Product Support Engineer