Support for leadtek winfast tv 2000 xp expert

[Alexander S. <al...@sa...>]

Hi

I have bought a leadtek winfast tv 2000 xp expert tv capture card to have with 
my mythtv box. I'm very confused at the moment if there are support for it.

First of all im using gentoo and have installed Linux Kernel v2.6.8-gentoo-r3 
with v4l Conexant 2388x (bt878 successor) support. It seams like the system 
recognize it. I get this during startup

Linux video capture interface: v1.00
cx2388x v4l2 driver version 0.0.4 loaded
ACPI: PCI interrupt 0000:02:0e.0[A] -> GSI 17 (level, low) -> IRQ 17
cx8800[0]: found at 0000:02:0e.0, rev: 5, irq: 17, latency: 64, 
mmio:0xfa000000
cx8800[0]: subsystem: 107d:6611, board: Leadtek Winfast 2000XP Expert 
[card=5,autodetected]
cx8800[0]: i2c register ok
cx8800[0]: Leadtek Winfast 2000 XP config: tuner=38, eeprom[0]=0x01
cx8800[0]: registered device video0 [v4l2]
cx8800[0]: registered device vbi0
cx8800[0]: registered device radio0
tuner: type set to 38 (Philips PAL/SECAM multi (FM1216ME MK3)) by cx8800[0]
cx8800[0]: i2c attach [client=Philips PAL/SECAM multi (FM1216ME MK3)]
tda9885/6/7: chip found @ 0x86
cx8800[0]: i2c attach [client=tda9887]

and then i get lots of
cx8800[0]: AUD_STATUS: 0xbb2 [mono/no pilot] ctl=BTSC_AUTO_STEREO

so there seams to be some kind of activity with the board..

I havent tried the card yet case i want the remote to work first (so that i 
can start to use the computer as a mp3 player). So i tried to do emerge lirc 
that downloads and install lirc. I figured out that configure should be run 
with --with-driver=leadtek_0010 to support my hardware? Gentoo is using 
version 0.7-pre7.

After a while i get a module called lirc_gpio

When i try to modprobe it i get this
FATAL: Error inserting lirc_gpio 
(/lib/modules/2.6.8-gentoo-r3/misc/lirc_gpio.ko): Unknown symbol in module, 
or unknown parameter (see dmesg)

and in dmesg i get this
lirc_dev: IR Remote Control driver registered, at major 61
lirc_gpio: Unknown symbol bttv_read_gpio
lirc_gpio: Unknown symbol bttv_get_cardinfo
lirc_gpio: Unknown symbol bttv_get_gpio_queue
lirc_gpio: Unknown symbol bttv_write_gpio
lirc_gpio: Unknown symbol bttv_gpio_enable

Isnt the bttv another chip family for other cards? Have i the wrong lirc 
drivers. Is my card supported? etc etc? I dont get it. I have tried to 
include bttv in the kernel but then i get this

FATAL: Error inserting lirc_gpio 
(/lib/modules/2.6.8-gentoo-r3/misc/lirc_gpio.ko): Invalid request code

and in dmesg i get this

lirc_dev: IR Remote Control driver registered, at major 61
lirc_gpio (-1): could not get card type

On the tv card there is a chip with this information
Connexant
Cx23881-19

Please help. I really would like my mythtv box to start working :)

/Alexander