Menu
▾
▴
Re: [Ivtv-users] PVR-500 hardware problems?
|
From: Scot L. H. <we...@cf...> - 2005-09-17 15:46:58
|
On Sat, 2005-09-17 at 01:00, Ross wrote: > On 9/17/05, Scot L. Harris <we...@cf...> wrote: > > Trying to install a PVR-500 along with a PVR-350 on a system that is to > > run mythtv 18.1 from the ATRPMs repo. Using ivtv 0.3.7k driver. > > Try the latest svn drivers, a fair bit has changed recently. > Have started looking into how to do this but have not been able to yet. > > The PVR-350 and the first tuner on the PVR-500 seem to work as > > expected. Unable to get the second tuner to capture any thing. > > Have you tried the PVR-500 on its own? > No I have not. Will schedule time tomorrow to try that. > > Get the following error message in /var/log/messages: > > > > Sep 16 17:21:28 terraslave kernel: ivtv warning: i2c client addr: 0x44 > > not found for command 0x80446468! > > Sep 16 17:21:28 terraslave kernel: ivtv warning: i2c client addr: 0x44 > > not found for command 0x400e6407! > > >From memory, that's the cx25840 chip that it's not picking up. Post > your full ivtv dmesg output. Hopefully this is what you want, if not let me know and I will try to get the info you requested. ivtv: ==================== START INIT IVTV ==================== ivtv: version 0.3.7 (k) loading ivtv: Linux version: 2.6.12-1.1447_FC4 686 REGPARM 4KSTACKS gcc-4.0 ivtv: In case of problems please include the debug info ivtv: between the START INIT IVTV and END INIT IVTV lines when ivtv: mailing the ivtv-devel mailinglist. ivtv: Autodetected WinTV PVR 350 card (iTVC15 based) ACPI: PCI Interrupt 0000:00:09.0[A] -> Link [LNKB] -> GSI 11 (level, low) -> IRQ 11 ivtv: Unreasonably low latency timer, setting to 64 (was 32) tveeprom: The eeprom says no radio is present, but the tuner type tveeprom: indicates otherwise. I will assume that radio is present. tveeprom: Hauppauge: model = 48132, rev = K268, serial# = 2985934 tveeprom: tuner = LG TAPE H001F MK3 (idx = 68, type = 47) tveeprom: tuner fmt = NTSC(M) (eeprom = 0x08, v4l2 = 0x00001000) tveeprom: audio processor = MSP4448 (type = 1b) tveeprom: decoder processor = SAA7115 (type = 13) ivtv: i2c attach to card #0 ok [client=tveeprom[50], addr=50] tuner: chip found at addr 0xc2 i2c-bus ivtv i2c driver #0 ivtv: i2c attach to card #0 ok [client=(tuner unset), addr=61] ivtv: i2c attach to card #0 ok [client=saa7115[50], addr=21] ivtv: i2c attach to card #0 ok [client=saa7127[50], addr=44] msp34xx: ivtv version msp34xx: init: chip=MSP3448W-A2, has NICAM support, simple (D) mode, simpler (G) no-thread mode msp34xx: $Id$ compiled on: Sep 2 2005 05:49:19 ivtv: i2c attach to card #0 ok [client=MSP3448W-A2, addr=40] ivtv: Encoder revision: 0x02040024 ivtv warning: Encoder Firmware can be buggy, use version 0x02040011!!!! ivtv: Decoder revision: 0x02020023 ivtv: Create DMA encoder MPEG stream: 0 x 32768 buffers (0KB total) ivtv: Create DMA encoder YUV stream: 0 x 10800 buffers (0KB total) ivtv: Create DMA encoder VBI stream: 0 x 17472 buffers (0KB total) ivtv: Create DMA encoder PCM audio stream: 0 x 4608 buffers (0KB total) ivtv: Create encoder radio stream ivtv: Create DMA decoder MPEG stream: 0 x 65536 buffers (0KB total) ivtv: Create DMA decoder VBI stream: 0 x 2048 buffers (0KB total) ivtv: Create decoder VOUT stream ivtv: Create DMA decoder YUV stream: 0 x 43200 buffers (0KB total) ivtv: Create DMA decoder OSD stream: 0 x 65536 buffers (0KB total) tuner: type set to 47 (LG NTSC (TAPE series)) by ivtv i2c driver #0 spurious 8259A interrupt: IRQ7. ivtv: Initialized WinTV PVR 350, card #0 ivtv: ====================== NEXT CARD ====================== ivtv: Autodetected WinTV PVR 150 card (iTVC16 based) ACPI: PCI Interrupt 0000:02:08.0[A] -> Link [LNKC] -> GSI 10 (level, low) -> IRQ 10 ivtv: Unreasonably low latency timer, setting to 64 (was 32) tveeprom: Hauppauge: model = 23552, rev = D492, serial# = 8099904 tveeprom: tuner = Philips FQ1236A MK4 (idx = 92, type = 57) tveeprom: tuner fmt = NTSC(M) (eeprom = 0x08, v4l2 = 0x00001000) tveeprom: audio processor = CX25843 (type = 25) tveeprom: decoder processor = CX25843 (type = 1e) ivtv: i2c attach to card #1 ok [client=tveeprom[50], addr=50] tuner: chip found at addr 0xc0 i2c-bus ivtv i2c driver #1 TEA5767 detected. ivtv: i2c attach to card #1 ok [client=(tuner unset), addr=60] tuner: type set to 62 (Philips TEA5767HN FM Radio) by autodetect type set to 62 (Philips TEA5767HN FM Radio) tuner: chip found at addr 0xc2 i2c-bus ivtv i2c driver #1 ivtv: i2c attach to card #1 ok [client=(tuner unset), addr=61] ivtv: This is the first unit of a PVR500 cx25840: firmware /lib/modules/HcwMakoA.ROM loaded ivtv: i2c attach to card #1 ok [client=cx25840[50], addr=44] ivtv: i2c attach to card #1 ok [client=wm8775[50], addr=1b] ivtv: Detected a TEA5767 radio tuner. Enabling radio support. ivtv: Encoder revision: 0x02040024 ivtv warning: Encoder Firmware can be buggy, use version 0x02040011!!!! ivtv: Create DMA encoder MPEG stream: 0 x 32768 buffers (0KB total) ivtv: Create DMA encoder YUV stream: 0 x 10800 buffers (0KB total) ivtv: Create DMA encoder VBI stream: 0 x 17472 buffers (0KB total) ivtv: Create DMA encoder PCM audio stream: 0 x 4608 buffers (0KB total) ivtv: Create encoder radio stream tuner: type set to 57 (Philips FQ1236A MK4) by ivtv i2c driver #1 ivtv: Initialized WinTV PVR 150, card #1 ivtv: ====================== NEXT CARD ====================== ivtv: Autodetected WinTV PVR 150 card (iTVC16 based) ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 3 PCI: setting IRQ 3 as level-triggered ACPI: PCI Interrupt 0000:02:09.0[A] -> Link [LNKD] -> GSI 3 (level, low) -> IRQ 3 ivtv: Unreasonably low latency timer, setting to 64 (was 32) tveeprom: Hauppauge: model = 23552, rev = D492, serial# = 8099904 tveeprom: tuner = Philips FQ1236A MK4 (idx = 92, type = 57) tveeprom: tuner fmt = NTSC(M) (eeprom = 0x08, v4l2 = 0x00001000) tveeprom: audio processor = CX25843 (type = 25) tveeprom: decoder processor = CX25843 (type = 1e) ivtv: i2c attach to card #2 ok [client=tveeprom[50], addr=50] tuner: chip found at addr 0xc2 i2c-bus ivtv i2c driver #2 ivtv: i2c attach to card #2 ok [client=(tuner unset), addr=61] ivtv: i2c attach to card #2 ok [client=wm8775[50], addr=1b] ivtv: This is the second unit of a PVR500 ivtv: Correcting tveeprom data: no radio present on second tuner ivtv warning: i2c client addr: 0x44 not found for command 0x800464cb! ivtv: Encoder revision: 0x02040024 ivtv warning: Encoder Firmware can be buggy, use version 0x02040011!!!! ivtv: Create DMA encoder MPEG stream: 0 x 32768 buffers (0KB total) ivtv: Create DMA encoder YUV stream: 0 x 10800 buffers (0KB total) ivtv: Create DMA encoder VBI stream: 0 x 17472 buffers (0KB total) ivtv: Create DMA encoder PCM audio stream: 0 x 4608 buffers (0KB total) tuner: type set to 57 (Philips FQ1236A MK4) by ivtv i2c driver #2 ivtv warning: i2c client addr: 0x44 not found for command 0x40046403! ivtv warning: i2c client addr: 0x44 not found for command 0x40046404! ivtv warning: i2c client addr: 0x44 not found for command 0x4004646e! ivtv warning: i2c client addr: 0x44 not found for command 0x40046403! ivtv warning: i2c client addr: 0x44 not found for command 0x40046406! ivtv warning: i2c client addr: 0x44 not found for command 0x40046406! ivtv: Initialized WinTV PVR 150, card #2 ivtv: ==================== END INIT IVTV ==================== ivtv-osd: Framebuffer module loaded (attached to ivtv card id 0) ivtv-osd warning: Framebuffer is at decoder-relative address 0x00510000 and has 1704960 bytes. ivtv-osd: screen coords: [0 0] -> [720 480] ivtv-osd: original global alpha = 208 ivtv-osd: current OSD state = 39 ivtv-osd: new global alpha = 208 (1 255 0) ivtv-osd: framebuffer at 0xe9510000, mapped to 0xf9810000, size 1350k ivtv-osd: mode is 720x480x32, linelength=2880 Console: switching to colour frame buffer device 90x30 ivtv-osd: fb0: iTVC15 TV out frame buffer device ivtv: Allocate DMA decoder OSD stream: 16 x 65536 buffers (1024KB total) lirc_dev: IR Remote Control driver registered, at major 61 bttv: disagrees about version of symbol tveeprom_hauppauge_analog bttv: Unknown symbol tveeprom_hauppauge_analog cx88xx: disagrees about version of symbol tveeprom_hauppauge_analog cx88xx: Unknown symbol tveeprom_hauppauge_analog cx8800: Unknown symbol cx88_reset cx8800: Unknown symbol cx88_call_i2c_clients cx8800: Unknown symbol cx88_wakeup cx8800: Unknown symbol cx88_risc_stopper cx8800: Unknown symbol cx88_print_irqbits cx8800: Unknown symbol cx88_set_scale cx8800: Unknown symbol cx88_shutdown cx8800: Unknown symbol cx88_vdev_init cx8800: Unknown symbol cx88_core_put cx8800: Unknown symbol cx88_audio_thread cx8800: Unknown symbol cx88_core_irq cx8800: Unknown symbol cx88_core_get cx8800: Unknown symbol cx88_get_stereo cx8800: Unknown symbol cx88_set_tvnorm cx8800: Unknown symbol cx88_vid_irqs cx8800: Unknown symbol cx88_risc_buffer cx8800: Unknown symbol cx88_set_stereo cx8800: Unknown symbol cx88_sram_channels cx8800: Unknown symbol cx88_set_tvaudio cx8800: Unknown symbol cx88_sram_channel_dump cx8800: Unknown symbol cx88_sram_channel_setup cx8800: Unknown symbol cx88_print_ioctl cx8800: Unknown symbol cx88_free_buffer cx8800: Unknown symbol cx88_boards cx8800: Unknown symbol cx88_newstation lirc_i2c: chip found @ 0x18 (Hauppauge IR) ivtv: i2c attach to card #0 ok [client=Hauppauge IR, addr=18] lirc_dev: lirc_register_plugin: sample_rate: 10 > > On the mythtv list there are other people seeing similar errors. > > Suspicion is that there is a batch of bad PVR-500 cards. > > > > Is there any other testing that can be done to verify that it is a bad > > card? Or is there a configuration option that I missed in setting this > > card up? > > I know it might be difficult, but how about trying the card in a windows box? I don't have a windows system here to try the card in. :) So this becomes very difficult to try. |