From: stone8936 <sto...@ho...> - 2013-01-25 10:10:24
|
Oh, the information printed is used in my kernel. I boot from SD card. I try your kernel again. However, I cannot load your u-boot.img. I copy MLO, u-boot.img and uImage to my first partition. The booting log: *Texas Instruments X-Loader 1.5.0 (Sep 16 2011 - 12:10:02) OMAP3503-GP ES3.1.2 Board revision: 1 Reading boot sector Loading u-boot.bin from nand U-Boot 2010.09-00000-g2894204-dirty (Jan 17 2013 - 13:52:57) OMAP3503-GP ES3.1.2, CPU-OPP2, L3-165MHz, Max CPU Clock 600 mHz Gumstix Overo board + LPDDR/NAND I2C: ready DRAM: 512 MiB NAND: 512 MiB *** Warning - bad CRC or NAND, using default environment In: serial Out: serial Err: serial Board revision: 1 Direct connection on mmc2 Die ID #72e4000700000000015154780d01f006 Net: smc911x-0 Hit any key to stop autoboot: 1 0 mmc1 is available reading boot.scr ** Unable to read "boot.scr" from mmc 0:1 ** reading uImage 2669904 bytes read Booting from mmc ... ## Booting kernel from Legacy Image at 82000000 ... Image Name: Linux-3.2.0 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 2669840 Bytes = 2.5 MiB Load Address: 80008000 Entry Point: 80008000 Verifying Checksum ... OK Loading Kernel Image ... OK OK Starting kernel ... Uncompressing Linux... done, booting the kernel. [ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Linux version 3.2.0 (scott@hex) (gcc version 4.6.4 20120303 (prerelease) (GCC) ) #1 PREEMPT Wed Jan 23 10:59:47 EST 2013 [ 0.000000] CPU: ARMv7 Processor [411fc087] revision 7 (ARMv7), cr=10c53c7d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT nonaliasing instruction cache [ 0.000000] Machine: Gumstix Overo [ 0.000000] Memory policy: ECC disabled, Data cache writeback [ 0.000000] OMAP3503 ES3.1.2 (l2cache neon isp ) [ 0.000000] Clocking rate (Crystal/Core/MPU): 26.0/332/500 MHz ...... [ 7.821075] smsc911x smsc911x.0: eth0: SMSC911x/921x identified at 0xe0816000, IRQ: 336*** And the module and spike test, does not work: *Yocto (Built by Poky 7.0.2) 1.2.2 overo ttyO2 overo login: root root@overo:~# uname -a Linux overo 3.2.0 #1 PREEMPT Wed Jan 23 10:59:47 EST 2013 armv7l GNU/Linux root@overo:~# insmod spike.ko [ 56.704772] Disabling lock debugging due to kernel taint root@overo:~# cat /dev/s spike Status: 0 TX: 0 1 2 3 RX: 255 255 255 255 root@overo:~# lsmod Module Size Used by spike 2927 0 ipv6 240002 10 * I try to change your u-boot name u-boot.img to u-boot.bin, I don't know the difference. stop at *Loading u-boot.bin from mmc*. -- View this message in context: http://gumstix.8.n6.nabble.com/SPI-problem-on-Overo-tp4966514p4966609.html Sent from the Gumstix mailing list archive at Nabble.com. |