From: Paul N. <pa...@id...> - 2011-03-28 12:41:12
|
Marshall, I solved the build problem by typing bitbake -b angstrom-version Then bitbaking the image again. OK, I now have 2.6.38 booting! No USB though. I removed the no USB patch from your recipe, will rebuild virtual/kernel to make sure. Hmm, still not working. No messages when plugging something in, no output from lsusb, same goes for the host and OTG ports. Did I miss something else? Thanks, Paul Nolan, CEO Idruna Software Inc. U-Boot 2010.09 (Mar 27 2011 - 17:14:17) OMAP3503-GP ES3.1, CPU-OPP2, L3-165MHz, Max CPU Clock 600 mHz Gumstix Overo board + LPDDR/NAND I2C: ready DRAM: 256 MiB NAND: 256 MiB *** Warning - bad CRC or NAND, using default environment In: serial Out: serial Err: serial Board revision: 0 Direct connection on mmc2 No EEPROM on expansion board Die ID #273e000400000000040398cf0200600b Net: No ethernet found. Hit any key to stop autoboot: 0 Overo # Overo # Overo # Overo # mmc init mmc1 is available Overo # setenv console ttyO2,115200n8 Overo # run loaduimage reading uImage 2939492 bytes read Overo # run mmcboot Booting from mmc ... ## Booting kernel from Legacy Image at 82000000 ... Image Name: Angstrom/2.6.38/overo Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 2939428 Bytes = 2.8 MiB Load Address: 80008000 Entry Point: 80008000 Verifying Checksum ... OK Loading Kernel Image ... OK OK Starting kernel ... Uncompressing Linux... done, booting the kernel. [ 0.000000] Linux version 2.6.38-rc8 (paul@ubuntu) (gcc version 4.3.3 (GCC) ) #1 Mon Mar 28 05:03:25 PDT 2011 [ 0.000000] CPU: ARMv7 Processor [411fc083] revision 3 (ARMv7), cr=10c53c7f [ 0.000000] CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction ca che [ 0.000000] Machine: Gumstix Overo [ 0.000000] Memory policy: ECC disabled, Data cache writeback [ 0.000000] OMAP3503 ES3.1 (l2cache neon isp ) [ 0.000000] SRAM: Mapped pa 0x40200000 to va 0xfe400000 size: 0x10000 [ 0.000000] Clocking rate (Crystal/Core/MPU): 26.0/224/500 MHz [ 0.000000] Reprogramming SDRC clock to 224791666 Hz [ 0.000000] dpll3_m2_clk rate change failed: -22 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pag es: 65024 [ 0.000000] Kernel command line: console=ttyO2,115200n8 mpurate=500 vram=12M omapfb.mode=dvi:1024x768MR-16@60 omapfb.debug=y omapdss.def_disp=dvi root=/dev/m mcblk0p2 rw rootfstype=ext3 rootwait [ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes) [ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Memory: 256MB = 256MB total [ 0.000000] Memory: 248292k/248292k available, 13852k reserved, 0K highmem [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) [ 0.000000] DMA : 0xffc00000 - 0xffe00000 ( 2 MB) [ 0.000000] vmalloc : 0xd0800000 - 0xf8000000 ( 632 MB) [ 0.000000] lowmem : 0xc0000000 - 0xd0000000 ( 256 MB) [ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB) [ 0.000000] .init : 0xc0008000 - 0xc004f000 ( 284 kB) [ 0.000000] .text : 0xc004f000 - 0xc057f930 (5315 kB) [ 0.000000] .data : 0xc0580000 - 0xc05f6e78 ( 476 kB) [ 0.000000] NR_IRQS:409 [ 0.000000] IRQ: Found an INTC at 0xfa200000 (revision 4.0) with 96 interrupt s [ 0.000000] Total of 96 interrupts on 1 active controller [ 0.000000] OMAP clockevent source: GPTIMER1 at 32768 Hz [ 0.000000] sched_clock: 32 bits at 32kHz, resolution 30517ns, wraps every 13 1071999ms [ 0.000000] Console: colour dummy device 80x30 [ 0.000000] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar [ 0.000000] ... MAX_LOCKDEP_SUBCLASSES: 8 [ 0.000000] ... MAX_LOCK_DEPTH: 48 [ 0.000000] ... MAX_LOCKDEP_KEYS: 8191 [ 0.000000] ... CLASSHASH_SIZE: 4096 [ 0.000000] ... MAX_LOCKDEP_ENTRIES: 16384 [ 0.000000] ... MAX_LOCKDEP_CHAINS: 32768 [ 0.000000] ... CHAINHASH_SIZE: 16384 [ 0.000000] memory used by lock dependency info: 3695 kB [ 0.000000] per task-struct memory footprint: 1152 bytes [ 0.001068] Calibrating delay loop... 498.87 BogoMIPS (lpj=1945600) [ 0.164123] pid_max: default: 32768 minimum: 301 [ 0.164764] Security Framework initialized [ 0.165161] Mount-cache hash table entries: 512 [ 0.169403] CPU: Testing write buffer coherency: ok [ 0.174285] devtmpfs: initialized [ 0.179931] omap_hwmod: _populate_mpu_rt_base found no _mpu_rt_va for l4_core [ 0.179931] omap_hwmod: _populate_mpu_rt_base found no _mpu_rt_va for l4_per [ 0.179962] omap_hwmod: _populate_mpu_rt_base found no _mpu_rt_va for l4_wkup [ 0.180480] omap_hwmod: gpt12_fck: missing clockdomain for gpt12_fck. [ 0.197601] omap_hwmod: i2c1: softreset failed (waited 10000 usec) [ 0.213195] omap_hwmod: i2c2: softreset failed (waited 10000 usec) [ 0.228759] omap_hwmod: i2c3: softreset failed (waited 10000 usec) [ 0.229583] omap_hwmod: am35x_otg_hs: cannot be enabled (3) [ 0.233093] print_constraints: dummy: [ 0.234680] NET: Registered protocol family 16 [ 0.235534] GPMC revision 5.0 [ 0.235687] Trying to install interrupt handler for IRQ402 [ 0.235717] Trying to install interrupt handler for IRQ403 [ 0.235748] Trying to install interrupt handler for IRQ404 [ 0.235748] Trying to install interrupt handler for IRQ405 [ 0.235778] Trying to install interrupt handler for IRQ406 [ 0.235809] Trying to install interrupt handler for IRQ407 [ 0.235839] Trying to install interrupt handler for IRQ408 [ 0.235870] Trying to install type control for IRQ409 [ 0.235870] Trying to set irq flags for IRQ409 [ 0.239410] omap_device: omap_gpio.0: new worst case activate latency 0: 1220 70 [ 0.240112] OMAP GPIO hardware version 2.5 [ 0.240722] OMAP GPIO hardware version 2.5 [ 0.241241] OMAP GPIO hardware version 2.5 [ 0.241790] OMAP GPIO hardware version 2.5 [ 0.242370] OMAP GPIO hardware version 2.5 [ 0.242950] OMAP GPIO hardware version 2.5 [ 0.249176] omap_mux_init: Add partition: #1: core, flags: 0 [ 0.254333] omap_device: omap_uart.0: new worst case activate latency 0: 3051 7 [ 0.254821] omap_device: omap_uart.0: new worst case deactivate latency 0: 30 517 [ 0.256744] Found NAND on CS0 [ 0.256744] Registering NAND on CS0 [ 0.267730] hw-breakpoint: debug architecture 0x4 unsupported. [ 0.437744] Switched to new clocking rate (Crystal/Core/MPU): 26.0/224/500 MH z [ 0.438781] OMAP DMA hardware revision 4.0 [ 0.456634] bio: create slab <bio-0> at 0 [ 0.460723] SCSI subsystem initialized [ 0.461578] omap_device: omap2_mcspi.1: new worst case activate latency 0: 61 035 [ 0.467041] usbcore: registered new interface driver usbfs [ 0.467437] usbcore: registered new interface driver hub [ 0.467926] usbcore: registered new device driver usb [ 0.468627] omap_device: omap_i2c.1: new worst case activate latency 0: 30517 [ 0.468963] omap_i2c omap_i2c.1: bus 1 rev3.12 at 2600 kHz [ 0.477844] twl4030: PIH (irq 7) chaining IRQs 368..375 [ 0.478027] twl4030: power (irq 373) chaining IRQs 376..383 [ 0.479675] twl4030: gpio (irq 368) chaining IRQs 384..401 [ 0.487945] print_constraints: VMMC1: 1850 <--> 3150 mV at 3000 mV normal sta ndby [ 0.488739] omap_device: omap_i2c.1: new worst case deactivate latency 0: 305 17 [ 0.489074] omap_i2c omap_i2c.3: bus 3 rev3.12 at 400 kHz [ 0.493835] Switching to clocksource 32k_counter [ 0.500457] Switched to NOHz mode on CPU #0 [ 0.588714] NET: Registered protocol family 2 [ 0.589599] IP route cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.591827] TCP established hash table entries: 8192 (order: 4, 65536 bytes) [ 0.592376] TCP bind hash table entries: 8192 (order: 6, 294912 bytes) [ 0.597747] TCP: Hash tables configured (established 8192 bind 8192) [ 0.597869] TCP reno registered [ 0.597930] UDP hash table entries: 128 (order: 1, 10240 bytes) [ 0.598297] UDP-Lite hash table entries: 128 (order: 1, 10240 bytes) [ 0.599639] NET: Registered protocol family 1 [ 0.601318] RPC: Registered udp transport module. [ 0.601348] RPC: Registered tcp transport module. [ 0.601348] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.603332] omap_init_opp_table: no hwmod or odev for iva, [8] cannot add OPP s. [ 0.798278] VFS: Disk quotas dquot_6.5.2 [ 0.798431] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.801849] JFFS2 version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 0.803253] msgmni has been set to 484 [ 0.809478] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 2 53) [ 0.809661] io scheduler noop registered [ 0.809692] io scheduler deadline registered [ 0.809936] io scheduler cfq registered (default) [ 0.812377] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 0.818481] omap_uart.0: ttyO0 at MMIO 0x4806a000 (irq = 72) is a OMAP UART0 [ 0.820037] omap_uart.1: ttyO1 at MMIO 0x4806c000 (irq = 73) is a OMAP UART1 [ 0.821014] omap_uart.2: ttyO2 at MMIO 0x49020000 (irq = 74) is a OMAP UART2 [ 1.553894] console [ttyO2] enabled [ 1.585449] brd: module loaded [ 1.601562] loop: module loaded [ 1.608673] mtdoops: mtd device (mtddev=name/number) must be supplied [ 1.615661] omap2-nand driver initializing [ 1.620635] ONFI flash detected [ 1.624267] NAND device: Manufacturer ID: 0x2c, Chip ID: 0xba (Micron NAND 25 6MiB 1,8V 16-bit) [ 1.633483] Creating 5 MTD partitions on "omap2-nand.0": [ 1.639129] 0x000000000000-0x000000080000 : "xloader" [ 1.652404] 0x000000080000-0x000000240000 : "uboot" [ 1.663391] 0x000000240000-0x000000280000 : "uboot environment" [ 1.674285] 0x000000280000-0x000000680000 : "linux" [ 1.685546] 0x000000680000-0x000010000000 : "rootfs" [ 1.813507] OneNAND driver initializing [ 1.821380] smsc911x: Driver version 2008-10-21. [ 1.827056] smsc911x: Driver version 2008-10-21. [ 1.832550] usbcore: registered new interface driver asix [ 1.838470] usbcore: registered new interface driver cdc_ether [ 1.844757] usbcore: registered new interface driver net1080 [ 1.850952] usbcore: registered new interface driver cdc_subset [ 1.857391] usbcore: registered new interface driver zaurus [ 1.863342] cdc_ncm: 7-Feb-2011 [ 1.866821] usbcore: registered new interface driver cdc_ncm [ 1.874389] usbcore: registered new interface driver cdc_wdm [ 1.880432] Initializing USB Mass Storage driver... [ 1.885864] usbcore: registered new interface driver usb-storage [ 1.892181] USB Mass Storage support registered. [ 1.897796] usbcore: registered new interface driver libusual [ 1.904174] usbcore: registered new interface driver usbtest [ 1.910156] udc: OMAP UDC driver, version: 4 October 2004 (iso) (dma) [ 1.919586] mousedev: PS/2 mouse device common for all mice [ 1.927825] omap_device: omap2_mcspi.1: new worst case deactivate latency 0: 30517 [ 1.936126] ads7846 spi1.0: unable to get regulator: -19 [ 1.944091] input: twl4030_pwrbutton as /devices/platform/omap/omap_i2c.1/i2c -1/1-0049/twl4030_pwrbutton/input/input0 [ 1.959320] twl_rtc twl_rtc: rtc core: registered twl_rtc as rtc0 [ 1.966033] omap_device: omap_i2c.1: new worst case activate latency 0: 12207 0 [ 1.975891] i2c /dev entries driver [ 1.982788] Driver for 1-wire Dallas network protocol. [ 1.989166] omap_device: omap_wdt.-1: new worst case activate latency 0: 3051 7 [ 1.998474] OMAP Watchdog Timer Rev 0x31: initial timeout 60 sec [ 2.005279] omap_device: omap_wdt.-1: new worst case deactivate latency 0: 30 517 [ 2.014221] twl4030_wdt twl4030_wdt: Failed to register misc device [ 2.020996] twl4030_wdt: probe of twl4030_wdt failed with error -16 [ 2.035400] usbcore: registered new interface driver usbhid [ 2.041381] usbhid: USB HID core driver [ 2.045410] oprofile: hardware counters not available [ 2.050750] oprofile: using timer interrupt. [ 2.056030] TCP cubic registered [ 2.059539] Initializing XFRM netlink socket [ 2.064208] NET: Registered protocol family 17 [ 2.069091] NET: Registered protocol family 15 [ 2.074401] Registering the dns_resolver key type [ 2.080139] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 1 [ 2.088562] ThumbEE CPU extension supported. [ 2.106719] Power Management for TI OMAP3. [ 2.154296] clock: disabling unused clocks to save power [ 2.167846] twl_rtc twl_rtc: setting system clock to 2011-03-28 05:24:42 UTC (1301289882) [ 2.180664] Waiting for root device /dev/mmcblk0p2... [ 2.620025] mmc0: host does not support reading read-only switch. assuming wr ite-enable. [ 2.642608] mmc0: new high speed SD card at address 0002 [ 2.651153] mmcblk0: mmc0:0002 00000 1.86 GiB [ 2.663604] mmcblk0: p1 p2 [ 2.740783] EXT3-fs: barriers not enabled [ 2.748229] kjournald starting. Commit interval 5 seconds [ 2.898468] EXT3-fs (mmcblk0p2): using internal journal [ 2.904937] EXT3-fs (mmcblk0p2): mounted filesystem with ordered data mode [ 2.912811] VFS: Mounted root (ext3 filesystem) on device 179:2. [ 2.926116] devtmpfs: mounted [ 2.929534] Freeing init memory: 284K INIT: version 2.86 booting Please wait: booting... Starting udev [ 4.329406] udevd (64): /proc/64/oom_adj is deprecated, please use /proc/64/o om_score_adj instead. Remounting root file system... Caching udev devnodes Populating dev cache [ 18.083618] Bluetooth: Core ver 2.15 [ 18.087707] NET: Registered protocol family 31 [ 18.092498] Bluetooth: HCI device and connection manager initialized [ 18.099517] Bluetooth: HCI socket layer initialized [ 18.148742] Bluetooth: L2CAP ver 2.15 [ 18.152770] Bluetooth: L2CAP socket layer initialized [ 18.187469] Bluetooth: HIDP (Human Interface Emulation) ver 1.2 [ 18.269989] Bluetooth: RFCOMM TTY layer initialized [ 18.275207] Bluetooth: RFCOMM socket layer initialized [ 18.280731] Bluetooth: RFCOMM ver 1.11 Cleaning: /etc/network/run/ifstate. Configuring network interfaces... done. Starting portmap daemon: portmap. net.ipv4.conf.default.rp_filter = 1 net.ipv4.conf.all.rp_filter = 1 Turning echo off on /dev/ttyS1 stty: standard input: Input/output error INIT: Entering runlevel: 5 Starting system message bus: dbus. Starting OpenBSD Secure Shell server: sshd done. Starting advanced power management daemon: No APM support in kernel (failed.) Starting ntpd: done Starting syslog-ng:. [ ok ]rting Avahi mDNS/DNS-SD Daemon: avahi-daemon Starting Bluetooth subsystem: Can't get port settings: Input/output error Can't initialize device: Input/output error .-------. | | .-. | | |-----.-----.-----.| | .----..-----.-----. | | | __ | ---'| '--.| .-'| | | | | | | | |--- || --'| | | ' | | | | '---'---'--'--'--. |-----''----''--' '-----'-'-'-' -' | '---' The Angstrom Distribution overo ttyO2 Angstrom 2010.7-test-20110328 overo ttyO2 |