Menu
▾
▴
Re: [Gumstix-users] Overo Fire / Sumitt board HDMI question -- Is my plug bad ?? -- need help
|
From: vwyodapink <vwy...@gm...> - 2010-05-25 22:03:13
|
Here is some more info from my overo incase this might help someone point out
what I am missing or doing incorrectly
Overo # printenv
bootcmd=if mmc init; then if run loadbootscript; then run bootscript; else
if run loaduimage; then run mmcboot; else run nandboot; fi; fi; else run
nandboot; fi
bootdelay=5
baudrate=115200
loadaddr=0x82000000
console=ttyS2,115200n8
vram=12M
mmcroot=/dev/mmcblk0p2 rw
mmcrootfstype=ext3 rootwait
nandroot=/dev/mtdblock4 rw
nandrootfstype=jffs2
mmcargs=setenv bootargs console=${console} vram=${vram}
omapfb.mode=dvi:${dvimode} omapfb.debug=y omapdss.def_disp=${defaultdisplay}
root=${mmcroot} rootfstype=${mmcrootfstype}
nandargs=setenv bootargs console=${console} vram=${vram}
omapfb.mode=dvi:${dvimode} omapfb.debug=y omapdss.def_disp=${defaultdisplay}
root=${nandroot} rootfstype=${nandrootfstype}
loadbootscript=fatload mmc 0 ${loadaddr} boot.scr
bootscript=echo Running bootscript from mmc ...; source ${loadaddr}
loaduimage=fatload mmc 0 ${loadaddr} uImage
mmcboot=echo Booting from mmc ...; run mmcargs; bootm ${loadaddr}
nandboot=echo Booting from nand ...; run nandargs; nand read ${loadaddr}
280000 400000; bootm ${loadaddr}
dieid#=48340004000000000403730511019004
dvimode=720p60
defaultdisplay=dvi
stdin=serial
stdout=serial
stderr=serial
Environment size: 1149/131068 bytes
Overo # boot
mmc1 is available
reading boot.scr
** Unable to read "boot.scr" from mmc 0:1 **
reading uImage
3159068 bytes read
Booting from mmc ...
## Booting kernel from Legacy Image at 82000000 ...
Image Name: Angstrom/2.6.33/overo
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 3159004 Bytes = 3 MB
Load Address: 80008000
Entry Point: 80008000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK
Starting kernel ...
Uncompressing Linux... done, booting the kernel.
Linux version 2.6.33 (st...@ww...) (gcc version 4.3.3 (GCC) ) #1
Tue May 11 14:01:22 PDT 2010
CPU: ARMv7 Processor [411fc083] revision 3 (ARMv7), cr=10c53c7f
CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache
Machine: Gumstix Overo
Memory policy: ECC disabled, Data cache writeback
OMAP3430/3530 ES3.1 (l2cache iva sgx neon isp )
SRAM: Mapped pa 0x40200000 to va 0xfe400000 size: 0x100000
Reserving 12582912 bytes SDRAM for VRAM
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024
Kernel command line: console=ttyS2,115200n8 vram=12M omapfb.mode=dvi:720p60
omapfb.debug=y omapdss.def_disp=dvi root=/dev/mmcblk0p2 rw rootfstype=ext3
rootwait
PID hash table entries: 1024 (order: 0, 4096 bytes)
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 128MB 128MB = 256MB total
Memory: 240640k/240916k available, 21228k reserved, 0K highmem
Virtual kernel memory layout:
vector : 0xffff0000 - 0xffff1000 ( 4 kB)
fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
DMA : 0xffc00000 - 0xffe00000 ( 2 MB)
vmalloc : 0xd0800000 - 0xf8000000 ( 632 MB)
lowmem : 0xc0000000 - 0xd0000000 ( 256 MB)
modules : 0xbf000000 - 0xc0000000 ( 16 MB)
.init : 0xc0008000 - 0xc00f2000 ( 936 kB)
.text : 0xc00f2000 - 0xc05f6000 (5136 kB)
.data : 0xc061a000 - 0xc0659980 ( 255 kB)
Hierarchical RCU implementation.
NR_IRQS:402
Clocking rate (Crystal/Core/MPU): 26.0/331/500 MHz
Could not get uart4_ick
Could not get uart4_fck
Reprogramming SDRC clock to 331882352 Hz
GPMC revision 5.0
IRQ: Found an INTC at 0xfa200000 (revision 4.0) with 96 interrupts
Total of 96 interrupts on 1 active controller
OMAP GPIO hardware version 2.5
OMAP clockevent source: GPTIMER1 at 32768 Hz
Console: colour dummy device 80x30
Calibrating delay loop... 499.92 BogoMIPS (lpj=1949696)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
devtmpfs: initialized
regulator: core version 0.5
NET: Registered protocol family 16
Found NAND on CS0
hw perfevents: enabled with ARMv7 Cortex-A8 PMU driver, 5 counters available
OMAP DMA hardware revision 4.0
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
i2c_omap i2c_omap.1: bus 1 rev3.12 at 2600 kHz
twl4030: PIH (irq 7) chaining IRQs 368..375
twl4030: power (irq 373) chaining IRQs 376..383
twl4030: gpio (irq 368) chaining IRQs 384..401
regulator: VUSB1V5: 1500 mV normal standby
regulator: VUSB1V8: 1800 mV normal standby
regulator: VUSB3V1: 3100 mV normal standby
twl4030_usb twl4030_usb: Initialized TWL4030 USB module
regulator: VMMC1: 1850 <--> 3150 mV at 3000 mV normal standby
regulator: VDAC: 1800 mV normal standby
regulator: VDVI: 1800 mV normal standby
i2c_omap i2c_omap.3: bus 3 rev3.12 at 400 kHz
Advanced Linux Sound Architecture Driver Version 1.0.22.1.
Bluetooth: Core ver 2.15
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
cfg80211: Calling CRDA to update world regulatory domain
Switching to clocksource 32k_counter
musb_hdrc: version 6.0, musb-dma, host, debug=0
musb_hdrc: USB Host mode controller at fa0ab000 using DMA, IRQ 92
musb_hdrc musb_hdrc: MUSB HDRC host driver
musb_hdrc musb_hdrc: new USB bus registered, assigned bus number 1
usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: MUSB HDRC host driver
usb usb1: Manufacturer: Linux 2.6.33 musb-hcd
usb usb1: SerialNumber: musb_hdrc
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
NET: Registered protocol family 2
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
VFS: Disk quotas dquot_6.5.2
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
JFFS2 version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
msgmni has been set to 470
alg: No test for stdrng (krng)
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
OMAP DSS rev 2.0
OMAP DISPC rev 3.0
OMAP VENC rev 2
OMAP DSI rev 1.0
Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
serial8250.0: ttyS0 at MMIO 0x4806a000 (irq = 72) is a ST16654
serial8250.1: ttyS1 at MMIO 0x4806c000 (irq = 73) is a ST16654
serial8250.2: ttyS2 at MMIO 0x49020000 (irq = 74) is a ST16654
console [ttyS2] enabled
brd: module loaded
loop: module loaded
omap2-nand driver initializing
NAND device: Manufacturer ID: 0x2c, Chip ID: 0xba (Micron NAND 256MiB 1,8V
16-bit)
cmdlinepart partition parsing not available
Creating 5 MTD partitions on "omap2-nand.0":
0x000000000000-0x000000080000 : "xloader"
0x000000080000-0x000000240000 : "uboot"
0x000000240000-0x000000280000 : "uboot environment"
0x000000280000-0x000000680000 : "linux"
0x000000680000-0x000010000000 : "rootfs"
smsc911x: Driver version 2008-10-21.
smsc911x: Driver version 2008-10-21.
usbcore: registered new interface driver asix
usbcore: registered new interface driver cdc_ether
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci-omap ehci-omap.0: OMAP-EHCI Host Controller
ehci-omap ehci-omap.0: new USB bus registered, assigned bus number 2
ehci-omap ehci-omap.0: irq 77, io mem 0x48064800
ehci-omap ehci-omap.0: USB 2.0 started, EHCI 1.00
usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: OMAP-EHCI Host Controller
usb usb2: Manufacturer: Linux 2.6.33 ehci_hcd
usb usb2: SerialNumber: ehci-omap.0
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 3 ports detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
udc: OMAP UDC driver, version: 4 October 2004 (iso) (dma)
mice: PS/2 mouse device common for all mice
twl_rtc twl_rtc: rtc core: registered twl_rtc as rtc0
twl_rtc twl_rtc: Power up reset detected.
twl_rtc twl_rtc: Enabling TWL-RTC.
i2c /dev entries driver
OMAP Watchdog Timer Rev 0x31: initial timeout 60 sec
twl4030_wdt twl4030_wdt: Failed to register misc device
twl4030_wdt: probe of twl4030_wdt failed with error -16
Bluetooth: HCI UART driver ver 2.2
Bluetooth: HCI H4 protocol initialized
Bluetooth: HCI BCSP protocol initialized
Bluetooth: HCILL protocol initialized
wacom driver registered
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
usbcore: registered new interface driver snd-usb-audio
No device for DAI omap-mcbsp-dai-0
No device for DAI omap-mcbsp-dai-1
No device for DAI omap-mcbsp-dai-2
No device for DAI omap-mcbsp-dai-3
No device for DAI omap-mcbsp-dai-4
overo SoC init
asoc: twl4030 <-> omap-mcbsp-dai-0 mapping ok
ALSA device list:
#0: overo (twl4030)
oprofile: using arm/armv7
TCP cubic registered
NET: Registered protocol family 17
NET: Registered protocol family 15
Bluetooth: L2CAP ver 2.14
Bluetooth: L2CAP socket layer initialized
Bluetooth: SCO (Voice Link) ver 0.6
Bluetooth: SCO socket layer initialized
Bluetooth: RFCOMM TTY layer initialized
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM ver 1.11
Bluetooth: BNEP (Ethernet Emulation) ver 1.3
Bluetooth: BNEP filters: protocol multicast
Bluetooth: HIDP (Human Interface Emulation) ver 1.2
ThumbEE CPU extension supported.
Power Management for TI OMAP3.
VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 1
Console: switching to colour frame buffer device 80x25
regulator_init_complete: incomplete constraints, leaving VDAC on
twl_rtc twl_rtc: setting system clock to 2000-01-01 00:00:00 UTC (946684800)
Waiting for root device /dev/mmcblk0p2...
mmc0: host does not support reading read-only switch. assuming write-enable.
mmc0: new high speed SDHC card at address 7902
mmcblk0: mmc0:7902 SD08G 7.42 GiB
mmcblk0: p1 p2
mmc1: new SDIO card at address 0001
kjournald starting. Commit interval 5 seconds
EXT3-fs (mmcblk0p2): using internal journal
EXT3-fs (mmcblk0p2): mounted filesystem with writeback data mode
VFS: Mounted root (ext3 filesystem) on device 179:2.
devtmpfs: mounted
Freeing init memory: 936K
INIT: version 2.86 booting
Please wait: booting...
Starting udev
udev: starting version 151
Remounting root file system...
udevadm settle - timeout of 3 seconds reached, the event queue contains:
/sys/devices/platform/ehci-omap.0/usb2/2-0:1.0 (553)
/sys/devices/platform/i2c_omap.1/i2c-1/1-0048 (557)
/sys/devices/platform/i2c_omap.1/i2c-1/1-0049 (558)
/sys/devices/platform/i2c_omap.1/i2c-1/1-0049/twl4030_gpio/gpio/gpiochip192
(559)
/sys/devices/platform/i2c_omap.1/i2c-1/1-004a (560)
/sys/devices/platform/i2c_omap.1/i2c-1/1-004b (561)
/sys/devices/platform/i2c_omap.1/i2c-1/1-004b/twl_reg.17/regulator/regulator.0
(562)
/sys/devices/platform/i2c_omap.1/i2c-1/1-004b/twl_reg.18/regulator/regulator.1
(563)
/sys/devices/platform/i2c_omap.1/i2c-1/1-004b/twl_reg.19/regulator/regulator.2
(564)
/sys/devices/platform/i2c_omap.1/i2c-1/1-004b/twl_reg.3/regulator/regulator.4
(565)
/sys/devices/platform/i2c_omap.1/i2c-1/1-004b/twl_reg.5/regulator/regulator.5
(566)
/sys/devices/platform/i2c_omap.1/i2c-1/1-004b/twl_reg.6/regulator/regulator.3
(567)
/sys/devices/platform/i2c_omap.1/i2c-1/1-004b/twl_rtc/rtc/rtc0 (568)
/sys/devices/platform/mmci-omap-hs.0/mmc_host/mmc0/mmc0:7902 (573)
/sys/devices/platform/mmci-omap-hs.0/mmc_host/mmc0/mmc0:7902/block/mmcblk0
(574)
/sys/devices/platform/mmci-omap-hs.0/mmc_host/mmc0/mmc0:7902/block/mmcblk0/mmcblk0p1
(575)
/sys/devices/platform/mmci-omap-hs.0/mmc_host/mmc0/mmc0:7902/block/mmcblk0/mmcblk0p2
(576)
/sys/devices/platform/mmci-omap-hs.1/mmc_host/mmc1/mmc1:0001 (578)
/sys/devices/platform/mmci-omap-hs.1/mmc_host/mmc1/mmc1:0001/mmc1:0001:1
(579)
/sys/devices/platform/musb_hdrc/usb1/1-0:1.0 (581)
/sys/devices/platform/omap2_mcspi.1/spi1.0 (584)
/sys/devices/platform/omap2_mcspi.1/spi1.1 (585)
lib80211: common routines for IEEE802.11 drivers
libertas_sdio: Libertas SDIO driver
libertas_sdio: Copyright Pierre Ossman
ads7846 spi1.0: touchscreen, irq 274
ads7846 spi1.0: no device detected, test read result was 0x00000000
libertas_sdio mmc1:0001:1: firmware: requesting sd8686_helper.bin
libertas_sdio mmc1:0001:1: firmware: requesting sd8686.bin
Caching udev devnodes
Populating dev cachelibertas: 00:50:43:02:fe:01, fw 9.70.3p24, cap
0x0000030b
mv: cannot stat `/tmp/uname': No such file or directory
libertas: wlan0: Marvell WLAN 802.11 adapter
NET: Registered protocol family 10
ALSA: Restoring mixer settings...
Configuring network interfaces... done.
Starting portmap daemon: portmap.
net.ipv4.conf.default.rp_filter = 1
net.ipv4.conf.all.rp_filter = 1
net.ipv4.ip_forward = 1
net.ipv6.conf.all.forwarding = 1
net.ipv4.conf.all.log_martians = 1
Tue May 4 17:39:00 BST 2010
Turning echo off on /dev/ttyS1
INIT: Entering runlevel: 5
Starting system message bus: dbus.
Starting Hardware abstraction layer hald
Starting syslog-ng:.
Starting OpenBSD Secure Shell server: sshd
done.
Starting advanced power management daemon: No APM support in kernel
(failed.)
Starting ntpd: done
Starting Samba: smbd nmbd.
Starting syslogd/klogd: done
* Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon
[ ok ]
Starting Bluetooth subsystem:
CSR build ID 0x0C-0x5C
Device setup complete
ttyS1 bluetoothd hid2hci rfcomm.
Waiting for connection on channel 1
Starting Network connection manager daemon: NetworkManager.
Starting PVR
Usage: insmod filename [args]
ADDRCONF(NETDEV_UP): wlan0: link is not ready
WARNING: Could not open
'/lib/modules/2.6.33/kernel/drivers/gpu/pvr/pvrsrvkm.ko': No such file or
directory
FATAL: Could not open
'/lib/modules/2.6.33/kernel/drivers/gpu/pvr/omaplfb.ko': No such file or
directory
WARNING: Could not open
'/lib/modules/2.6.33/kernel/drivers/gpu/pvr/pvrsrvkm.ko': No such file or
directory
FATAL: Could not open
'/lib/modules/2.6.33/kernel/drivers/gpu/pvr/bufferclass_ti.ko': No such file
or directory
mknod: missing operand after `0'
Try `mknod --help' for more information.
chmod: cannot access `/dev/pvrsrvkm': No such file or directory
cups: started scheduler.
Starting GPE display manager: gpe-dm
.-------.
| | .-.
| | |-----.-----.-----.| | .----..-----.-----.
| | | __ | ---'| '--.| .-'| | |
| | | | | |--- || --'| | | ' | | | |
'---'---'--'--'--. |-----''----''--' '-----'-'-'-'
-' |
'---'
The Angstrom Distribution overo ttyS2
Angstrom 2010.4-test-20100504 overo ttyS2
overo login:
overo login: root
root@overo:~# fbset
mode "640x400-70"
# D: 25.176 MHz, H: 31.469 kHz, V: 69.932 Hz
geometry 640 400 640 400 32
timings 39721 40 24 39 9 96 2
rgba 8/16,8/8,8/0,8/24
endmode
root@overo:~#
root@overo:~# dmesg
Linux version 2.6.33 (st...@ww...) (gcc version 4.3.3 (GCC) ) #1
Tue May 11 14:01:22 PDT 2010
CPU: ARMv7 Processor [411fc083] revision 3 (ARMv7), cr=10c53c7f
CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache
Machine: Gumstix Overo
Memory policy: ECC disabled, Data cache writeback
On node 0 totalpages: 65536
free_area_init_node: node 0, pgdat c0659344, node_mem_map c068b000
Normal zone: 512 pages used for memmap
Normal zone: 0 pages reserved
Normal zone: 65024 pages, LIFO batch:15
OMAP3430/3530 ES3.1 (l2cache iva sgx neon isp )
SRAM: Mapped pa 0x40200000 to va 0xfe400000 size: 0x100000
Reserving 12582912 bytes SDRAM for VRAM
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024
Kernel command line: console=ttyS2,115200n8 vram=12M omapfb.mode=dvi:720p60
omapfb.debug=y omapdss.def_disp=dvi root=/dev/mmcblk0p2 rw rootfstype=ext3
rootwait
PID hash table entries: 1024 (order: 0, 4096 bytes)
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 128MB 128MB = 256MB total
Memory: 240640k/240916k available, 21228k reserved, 0K highmem
Virtual kernel memory layout:
vector : 0xffff0000 - 0xffff1000 ( 4 kB)
fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
DMA : 0xffc00000 - 0xffe00000 ( 2 MB)
vmalloc : 0xd0800000 - 0xf8000000 ( 632 MB)
lowmem : 0xc0000000 - 0xd0000000 ( 256 MB)
modules : 0xbf000000 - 0xc0000000 ( 16 MB)
.init : 0xc0008000 - 0xc00f2000 ( 936 kB)
.text : 0xc00f2000 - 0xc05f6000 (5136 kB)
.data : 0xc061a000 - 0xc0659980 ( 255 kB)
Hierarchical RCU implementation.
NR_IRQS:402
Clocking rate (Crystal/Core/MPU): 26.0/331/500 MHz
Could not get uart4_ick
Could not get uart4_fck
Reprogramming SDRC clock to 331882352 Hz
GPMC revision 5.0
IRQ: Found an INTC at 0xfa200000 (revision 4.0) with 96 interrupts
Total of 96 interrupts on 1 active controller
OMAP GPIO hardware version 2.5
OMAP clockevent source: GPTIMER1 at 32768 Hz
Console: colour dummy device 80x30
Calibrating delay loop... 499.92 BogoMIPS (lpj=1949696)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
devtmpfs: initialized
regulator: core version 0.5
NET: Registered protocol family 16
Found NAND on CS0
hw perfevents: enabled with ARMv7 Cortex-A8 PMU driver, 5 counters available
OMAP DMA hardware revision 4.0
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
i2c_omap i2c_omap.1: bus 1 rev3.12 at 2600 kHz
twl4030: PIH (irq 7) chaining IRQs 368..375
twl4030: power (irq 373) chaining IRQs 376..383
twl4030: gpio (irq 368) chaining IRQs 384..401
machine_constraints_voltage: override 'VUSB1V5' min_uV, 1 -> 1500000
machine_constraints_voltage: override 'VUSB1V5' max_uV, 2147483647 ->
1500000
regulator: VUSB1V5: 1500 mV normal standby
machine_constraints_voltage: override 'VUSB1V8' min_uV, 1 -> 1800000
machine_constraints_voltage: override 'VUSB1V8' max_uV, 2147483647 ->
1800000
regulator: VUSB1V8: 1800 mV normal standby
machine_constraints_voltage: override 'VUSB3V1' min_uV, 1 -> 3100000
machine_constraints_voltage: override 'VUSB3V1' max_uV, 2147483647 ->
3100000
regulator: VUSB3V1: 3100 mV normal standby
twl4030_usb twl4030_usb: HW_CONDITIONS 0x50/80; link 1
twl4030_usb twl4030_usb: Initialized TWL4030 USB module
regulator: VMMC1: 1850 <--> 3150 mV at 3000 mV normal standby
regulator: VDAC: 1800 mV normal standby
regulator: VDVI: 1800 mV normal standby
i2c_omap i2c_omap.3: bus 3 rev3.12 at 400 kHz
Advanced Linux Sound Architecture Driver Version 1.0.22.1.
Bluetooth: Core ver 2.15
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
cfg80211: Calling CRDA to update world regulatory domain
Switching to clocksource 32k_counter
musb_hdrc: version 6.0, musb-dma, host, debug=0
HS USB OTG: revision 0x33, sysconfig 0x2010, sysstatus 0x1, intrfsel 0x1,
simenable 0x0
musb_hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, bulk combine, bulk split,
HB-ISO Rx, HB-ISO Tx, SoftConn)
musb_hdrc: MHDRC RTL version 1.400
musb_hdrc: setup fifo_mode 4
musb_hdrc: 28/31 max ep, 16384/16384 memory
musb_hdrc: USB Host mode controller at fa0ab000 using DMA, IRQ 92
musb_hdrc musb_hdrc: MUSB HDRC host driver
drivers/usb/core/inode.c: creating file 'devices'
drivers/usb/core/inode.c: creating file '001'
musb_hdrc musb_hdrc: new USB bus registered, assigned bus number 1
usb usb1: default language 0x0409
usb usb1: udev 1, busnum 1, minor = 0
usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: MUSB HDRC host driver
usb usb1: Manufacturer: Linux 2.6.33 musb-hcd
usb usb1: SerialNumber: musb_hdrc
usb usb1: uevent
usb usb1: usb_probe_device
usb usb1: configuration #1 chosen from 1 choice
usb usb1: adding 1-0:1.0 (config #1, interface 0)
usb 1-0:1.0: uevent
hub 1-0:1.0: usb_probe_interface
hub 1-0:1.0: usb_probe_interface - got id
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
hub 1-0:1.0: standalone hub
hub 1-0:1.0: individual port power switching
hub 1-0:1.0: no over-current protection
hub 1-0:1.0: power on to power good time: 10ms
hub 1-0:1.0: 100mA bus power budget for each child
hub 1-0:1.0: local power source is good
hub 1-0:1.0: enabling power on all ports
drivers/usb/core/inode.c: creating file '001'
NET: Registered protocol family 2
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
VFS: Disk quotas dquot_6.5.2
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
JFFS2 version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
msgmni has been set to 470
alg: No test for stdrng (krng)
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
OMAP DSS rev 2.0
OMAP DISPC rev 3.0
OMAP VENC rev 2
OMAP DSI rev 1.0
hub 1-0:1.0: state 7 ports 1 chg 0000 evt 0000
Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
serial8250.0: ttyS0 at MMIO 0x4806a000 (irq = 72) is a ST16654
serial8250.1: ttyS1 at MMIO 0x4806c000 (irq = 73) is a ST16654
serial8250.2: ttyS2 at MMIO 0x49020000 (irq = 74) is a ST16654
console [ttyS2] enabled
brd: module loaded
loop: module loaded
omap2-nand driver initializing
NAND device: Manufacturer ID: 0x2c, Chip ID: 0xba (Micron NAND 256MiB 1,8V
16-bit)
cmdlinepart partition parsing not available
Creating 5 MTD partitions on "omap2-nand.0":
0x000000000000-0x000000080000 : "xloader"
0x000000080000-0x000000240000 : "uboot"
0x000000240000-0x000000280000 : "uboot environment"
0x000000280000-0x000000680000 : "linux"
0x000000680000-0x000010000000 : "rootfs"
smsc911x: Driver version 2008-10-21.
smsc911x: Driver version 2008-10-21.
usbcore: registered new interface driver asix
usbcore: registered new interface driver cdc_ether
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci_hcd: block sizes: qh 60 qtd 96 itd 160 sitd 96
ehci-omap ehci-omap.0: failed to get ehci port1 regulator
ehci-omap ehci-omap.0: starting TI EHCI USB Controller
ehci-omap ehci-omap.0: TLL RESET DONE
ehci-omap ehci-omap.0: OMAP3 ES version > ES2.1
ehci-omap ehci-omap.0: UHH setup done, uhh_hostconfig=21c
ehci-omap ehci-omap.0: OMAP-EHCI Host Controller
drivers/usb/core/inode.c: creating file '002'
ehci-omap ehci-omap.0: new USB bus registered, assigned bus number 2
ehci-omap ehci-omap.0: park 0
ehci-omap ehci-omap.0: irq 77, io mem 0x48064800
ehci-omap ehci-omap.0: reset command 090b02 park=3 ithresh=9 period=1024
Reset HALT
ehci-omap ehci-omap.0: init command 010009 (park)=0 ithresh=1 period=256 RUN
ehci-omap ehci-omap.0: USB 2.0 started, EHCI 1.00
usb usb2: default language 0x0409
usb usb2: udev 1, busnum 2, minor = 128
usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: OMAP-EHCI Host Controller
usb usb2: Manufacturer: Linux 2.6.33 ehci_hcd
usb usb2: SerialNumber: ehci-omap.0
usb usb2: uevent
usb usb2: usb_probe_device
usb usb2: configuration #1 chosen from 1 choice
usb usb2: adding 2-0:1.0 (config #1, interface 0)
usb 2-0:1.0: uevent
hub 2-0:1.0: usb_probe_interface
hub 2-0:1.0: usb_probe_interface - got id
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 3 ports detected
hub 2-0:1.0: standalone hub
hub 2-0:1.0: individual port power switching
hub 2-0:1.0: individual port over-current protection
hub 2-0:1.0: power on to power good time: 20ms
hub 2-0:1.0: local power source is good
hub 2-0:1.0: enabling power on all ports
drivers/usb/core/inode.c: creating file '001'
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
udc: OMAP UDC driver, version: 4 October 2004 (iso) (dma)
mice: PS/2 mouse device common for all mice
twl_rtc twl_rtc: rtc core: registered twl_rtc as rtc0
twl_rtc twl_rtc: Power up reset detected.
twl_rtc twl_rtc: Enabling TWL-RTC.
i2c /dev entries driver
OMAP Watchdog Timer Rev 0x31: initial timeout 60 sec
twl4030_wdt twl4030_wdt: Failed to register misc device
twl4030_wdt: probe of twl4030_wdt failed with error -16
Bluetooth: HCI UART driver ver 2.2
Bluetooth: HCI H4 protocol initialized
Bluetooth: HCI BCSP protocol initialized
Bluetooth: HCILL protocol initialized
wacom driver registered
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
usbcore: registered new interface driver snd-usb-audio
hub 2-0:1.0: state 7 ports 3 chg 0000 evt 0000
No device for DAI omap-mcbsp-dai-0
No device for DAI omap-mcbsp-dai-1
No device for DAI omap-mcbsp-dai-2
No device for DAI omap-mcbsp-dai-3
No device for DAI omap-mcbsp-dai-4
overo SoC init
asoc: twl4030 <-> omap-mcbsp-dai-0 mapping ok
ALSA device list:
#0: overo (twl4030)
oprofile: using arm/armv7
TCP cubic registered
NET: Registered protocol family 17
NET: Registered protocol family 15
Bluetooth: L2CAP ver 2.14
Bluetooth: L2CAP socket layer initialized
Bluetooth: SCO (Voice Link) ver 0.6
Bluetooth: SCO socket layer initialized
Bluetooth: RFCOMM TTY layer initialized
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM ver 1.11
Bluetooth: BNEP (Ethernet Emulation) ver 1.3
Bluetooth: BNEP filters: protocol multicast
Bluetooth: HIDP (Human Interface Emulation) ver 1.2
ThumbEE CPU extension supported.
Power Management for TI OMAP3.
VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 1
OMAPFB: omapfb_init
OMAPFB: omapfb_probe
OMAPFB: create 3 framebuffers
OMAPFB: fb_infos allocated
OMAPFB: allocating 1024000 bytes for fb 0
OMAPFB: allocated VRAM paddr 8088e000, vaddr d0a00000
OMAPFB: region0 phys 8088e000 virt d0a00000 size=1024000
OMAPFB: region1 phys 00000000 virt (null) size=0
OMAPFB: region2 phys 00000000 virt (null) size=0
OMAPFB: fbmems allocated
OMAPFB: check_fb_var 0
OMAPFB: max frame size 1024000, line size 2560
OMAPFB: xres = 640, yres = 400, vxres = 640, vyres = 400
OMAPFB: set_fb_fix
OMAPFB: fb_infos initialized
OMAPFB: set_par(0)
OMAPFB: set_fb_fix
OMAPFB: apply_changes, fb 0, ovl 0
OMAPFB: setup_overlay 0, posx 0, posy 0, outw 640, outh 400
OMAPFB: paddr 8088e000, vaddr d0a00000
OMAPFB: pan_display(0)
OMAPFB: setcmap
OMAPFB: setcmap
Console: switching to colour frame buffer device 80x25
OMAPFB: pan_display(0)
OMAPFB: setcmap
OMAPFB: setcmap
OMAPFB: framebuffers registered
OMAPFB: apply_changes, fb 0, ovl 0
OMAPFB: setup_overlay 0, posx 0, posy 0, outw 640, outh 400
OMAPFB: paddr 8088e000, vaddr d0a00000
OMAPFB: apply_changes, fb 1, ovl 1
OMAPFB: apply_changes, fb 2, ovl 2
OMAPFB: create sysfs for fbs
OMAPFB: create sysfs for fbs
OMAPFB: create_framebuffers done
OMAPFB: mgr->apply'ed
regulator_init_complete: incomplete constraints, leaving VDAC on
twl_rtc twl_rtc: setting system clock to 2000-01-01 00:00:00 UTC (946684800)
Waiting for root device /dev/mmcblk0p2...
mmc0: host does not support reading read-only switch. assuming write-enable.
mmc0: new high speed SDHC card at address 7902
mmcblk0: mmc0:7902 SD08G 7.42 GiB
mmcblk0: p1 p2
mmc1: new SDIO card at address 0001
kjournald starting. Commit interval 5 seconds
EXT3-fs (mmcblk0p2): using internal journal
EXT3-fs (mmcblk0p2): mounted filesystem with writeback data mode
VFS: Mounted root (ext3 filesystem) on device 179:2.
devtmpfs: mounted
Freeing init memory: 936K
OMAPFB: pan_display(0)
OMAPFB: setcmap
OMAPFB: setcmap
OMAPFB: user mmap region start 8088e000, len 1024000, off 8088e000
hub 1-0:1.0: hub_suspend
usb usb1: bus auto-suspend
udev: starting version 151
usb usb2: uevent
usb 2-0:1.0: uevent
usb usb2: uevent
usb usb1: uevent
usb 1-0:1.0: uevent
usb usb1: uevent
hub 2-0:1.0: hub_suspend
usb usb2: bus auto-suspend
ehci-omap ehci-omap.0: suspend root hub
lib80211: common routines for IEEE802.11 drivers
lib80211_crypt: registered algorithm 'NULL'
libertas_sdio: Libertas SDIO driver
libertas_sdio: Copyright Pierre Ossman
ads7846 spi1.0: touchscreen, irq 274
ads7846 spi1.0: no device detected, test read result was 0x00000000
libertas_sdio mmc1:0001:1: firmware: requesting sd8686_helper.bin
libertas_sdio mmc1:0001:1: firmware: requesting sd8686.bin
libertas: 00:50:43:02:fe:01, fw 9.70.3p24, cap 0x0000030b
libertas: wlan0: Marvell WLAN 802.11 adapter
NET: Registered protocol family 10
usb usb2: uevent
usb 2-0:1.0: uevent
usb usb1: uevent
usb 1-0:1.0: uevent
OMAPFB: check_var(0)
OMAPFB: check_fb_var 0
OMAPFB: max frame size 1024000, line size 2560
OMAPFB: xres = 640, yres = 400, vxres = 640, vyres = 400
OMAPFB: set_par(0)
OMAPFB: set_fb_fix
OMAPFB: apply_changes, fb 0, ovl 0
OMAPFB: setup_overlay 0, posx 0, posy 0, outw 640, outh 400
OMAPFB: paddr 8088e000, vaddr d0a00000
OMAPFB: pan_display(0)
OMAPFB: setcmap
OMAPFB: check_var(0)
OMAPFB: check_fb_var 0
OMAPFB: max frame size 1024000, line size 2560
OMAPFB: can't fit FB into memory, reducing y
OMAPFB: xres = 640, yres = 400, vxres = 640, vyres = 400
OMAPFB: set_par(0)
OMAPFB: set_fb_fix
OMAPFB: apply_changes, fb 0, ovl 0
OMAPFB: setup_overlay 0, posx 0, posy 0, outw 640, outh 400
OMAPFB: paddr 8088e000, vaddr d0a00000
OMAPFB: pan_display(0)
OMAPFB: setcmap
ADDRCONF(NETDEV_UP): wlan0: link is not ready
OMAPFB: pan_display(0)
OMAPFB: setcmap
OMAPFB: setcmap
OMAPFB: check_var(0)
OMAPFB: check_fb_var 0
OMAPFB: max frame size 1024000, line size 2560
OMAPFB: xres = 640, yres = 400, vxres = 640, vyres = 400
OMAPFB: set_par(0)
OMAPFB: set_fb_fix
OMAPFB: apply_changes, fb 0, ovl 0
OMAPFB: setup_overlay 0, posx 0, posy 0, outw 640, outh 400
OMAPFB: paddr 8088e000, vaddr d0a00000
OMAPFB: pan_display(0)
OMAPFB: setcmap
OMAPFB: pan_display(0)
OMAPFB: setcmap
OMAPFB: setcmap
OMAPFB: setcmap
OMAPFB: ioctl QUERY_MEM
OMAPFB: user mmap region start 8088e000, len 1024000, off 8088e000
OMAPFB: ioctl QUERY_PLANE
OMAPFB: ioctl SETUP_PLANE
OMAPFB: omapfb_setup_plane
OMAPFB: ioctl QUERY_PLANE
OMAPFB: ioctl SETUP_PLANE
OMAPFB: omapfb_setup_plane
OMAPFB: ioctl QUERY_MEM
OMAPFB: ioctl QUERY_PLANE
OMAPFB: ioctl GET_CAPS
root@overo:~#
Not sure what else I can post to show whats going on with the port
everything in dmesg seems the same if the HDMI cable is plugged in or not.
The computer monitor should be working with stock display resolution but it
doesnt nor does my HDTV work with any of the settings nor the 720p setting.
Let me know if I can post something else to help figure it out. Or if there
is an actual step by step to show how to properly set this up I would happy
with that but I can not find anything current on here nor on google. What I
find on here is for old uboot triggers and modifying them to fit the current
style doesnt work for either.
vwyodapink wrote:
>
> Any chance anyone has any ideas on this? I need to connect to a monitor
> and I can not set it up to get the DVI monitor nor my HDtv to work with
> the HDMI port. Above I posted how I have tried to do this. Am I missing
> something? Does the change have to be in the kernel as well as uboot? I
> have also tried doing 800x600MR-24@60 with no luck as well. Is there a way
> to test if the port is bad?
>
> Thanks
>
>
>
> vwyodapink wrote:
>>
>> I went and bought a new monitor today that has hdmi and dvi plugs on it
>> and I still can not get anything to show up on either my hd tv nor the
>> new monitor. Here are the settings I have tried.
>> 640x480MR-16@60
>> 800x600MR-16@60
>> 1024x768MR-16@60
>> 1280x800MR-16@60
>> 1280x1024MR-16@60
>> 1440x900MR-16@60
>> 1680x1050MR-16@60
>>
>> I tried these in uboot like I have found to do and have done the
>> following commands to set and save them.
>> setenv dvimode (one of the settings about)
>> saveenv
>> boot
>>
>> Am I missing something here? I figured the tv was the issue since I have
>> read that the port does not give signals most tv's like (though I can
>> send any of these settings from my computer to the same tv and monitor
>> that are not working with the gumstix) I have tried both the on board
>> nand version and the most current desktop image you can DL. I have not
>> had luck building my own yet. Could the summit board have a bad hdmi
>> port?
>>
>> Thanks for any help figuring this out.
>> J
>>
>>
>> vwyodapink wrote:
>>>
>>> I am trying to get the HDMI output working on my fire/sumitt combo and
>>> my monitor accepts 480i, 480p, 720p, 1080p. I am trying to get the 480p
>>> working @ 60hz using the latest desktop image for DL. I have tried
>>>
>>> setenv dvimode 640x480-16@60
>>> saveenv
>>>
>>> and I also tried
>>> setenv dvimode 800x600-16@60
>>> saveenv
>>>
>>> and I am still not seeing anything on the display. I have booted this
>>> from console a few times and I waited over 20 min each time to make sure
>>> it fully booted from the sd card, which should have been more than
>>> enough time since it doesnt take that long on console.
>>>
>>> Can some help me out with what I should be doing?
>>>
>>> Thank you!
>>>
>>>
>>>
>>
>>
>
>
--
View this message in context: http://old.nabble.com/Overo-Fire---Sumitt-board-HDMI-question-tp28603720p28674113.html
Sent from the Gumstix mailing list archive at Nabble.com.
|