Menu
▾
▴
[Gumstix-users] overo_palmtop_200910121635 image +touch screen problem &log
|
From: ekrem <eha...@ho...> - 2009-11-28 09:45:01
|
hi everbody
I am newbies boot is normal palmtop images but touch screen isnot woking
correctly
I have search info in this forum but dont found it for me.
can you help me
regards
this is my log
Texas Instruments X-Loader 1.4.2 (Feb 19 2009 - 12:01:24)
Reading boot sector
Loading u-boot.bin from mmc
U-Boot 2009.08 (Oct 12 2009 - 18:16:02)
OMAP3530-GP ES3.1, CPU-OPP2 L3-165MHz
Gumstix Overo board + LPDDR/NAND
I2C: ready
DRAM: 256 MB
NAND: 256 MiB
In: serial
Out: serial
Err: serial
Die ID #538c00040000000004035c1401005016
Net: smc911x-0
Hit any key to stop autoboot: 5 4 3 2 1 0
mmc1 is available
reading boot.scr
** Unable to read "boot.scr" from mmc 0:1 **
reading uImage
3075240 bytes read
Booting from mmc ...
## Booting kernel from Legacy Image at 82000000 ...
Image Name: Angstrom/2.6.31/overo
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 3075176 Bytes = 2.9 MB
Load Address: 80008000
Entry Point: 80008000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK
Starting kernel ...
Uncompressing
Linux...........................................................................................................................................................................................................
done, booting the kernel.
Linux version 2.6.31-omap1 (sakoman@otto) (gcc version 4.3.3 (GCC) ) #1 Mon
Oct 12 18:25:39 PDT 2009
CPU: ARMv7 Processor [411fc083] revision 3 (ARMv7), cr=10c53c7f
CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache
Machine: Gumstix Overo
Memory policy: ECC disabled, Data cache writeback
OMAP3430 ES3.1
SRAM: Mapped pa 0x40200000 to va 0xe3000000 size: 0x100000
Reserving 12582912 bytes SDRAM for VRAM
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024
Kernel command line: console=ttyS2,115200n8 vram=12M
omapfb.mode=dvi:1024x768MR-16@60 omapfb.debug=y omapdss.def_disp=lcd43
root=/dev/mmcblk0p2 rw rootfstype=ext3 rootwait
PID hash table entries: 1024 (order: 10, 4096 bytes)
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 128MB 128MB = 256MB total
Memory: 240640KB available (5052K code, 575K data, 924K init, 0K highmem)
NR_IRQS:402
Clocking rate (Crystal/Core/MPU): 26.0/332/500 MHz
Reprogramming SDRC clock to 332000000 Hz
GPMC revision 5.0
IRQ: Found an INTC at 0xd8200000 (revision 4.0) with 96 interrupts
Total of 96 interrupts on 1 active controller
OMAP34xx GPIO hardware version 2.5
OMAP clockevent source: GPTIMER1 at 32768 Hz
Console: colour dummy device 80x30
Calibrating delay loop... 499.92 BogoMIPS (lpj=1949696)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
regulator: core version 0.5
NET: Registered protocol family 16
Found NAND on CS0
Registering NAND on CS0
OMAP DMA hardware revision 4.0
bio: create slab <bio-0> at 0
i2c_omap i2c_omap.1: bus 1 rev3.12 at 2600 kHz
twl4030: PIH (irq 7) chaining IRQs 368..375
twl4030: power (irq 373) chaining IRQs 376..383
twl4030: gpio (irq 368) chaining IRQs 384..401
regulator: VMMC1: 1850 <--> 3150 mV normal standby
regulator: VDAC: 1800 mV normal standby
regulator: VUSB1V5: 1500 mV normal standby
regulator: VUSB1V8: 1800 mV normal standby
regulator: VUSB3V1: 3100 mV normal standby
regulator: VPLL2: 1800 mV normal standby
i2c_omap i2c_omap.3: bus 3 rev3.12 at 400 kHz
SCSI subsystem initialized
twl4030_usb twl4030_usb: Initialized TWL4030 USB module
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
Bluetooth: Core ver 2.15
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
cfg80211: Using static regulatory domain info
cfg80211: Regulatory domain: US
(start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
(2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2700 mBm)
(5170000 KHz - 5190000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
(5190000 KHz - 5210000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
(5210000 KHz - 5230000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
(5230000 KHz - 5330000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
(5735000 KHz - 5835000 KHz @ 40000 KHz), (600 mBi, 3000 mBm)
cfg80211: Calling CRDA for country: US
musb_hdrc: version 6.0, musb-dma, host, debug=0
musb_hdrc: USB Host mode controller at d80ab000 using DMA, IRQ 92
musb_hdrc musb_hdrc: MUSB HDRC host driver
musb_hdrc musb_hdrc: new USB bus registered, assigned bus number 1
usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: MUSB HDRC host driver
usb usb1: Manufacturer: Linux 2.6.31-omap1 musb-hcd
usb usb1: SerialNumber: musb_hdrc
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
NET: Registered protocol family 2
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP reno registered
NET: Registered protocol family 1
VFS: Disk quotas dquot_6.5.2
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
JFFS2 version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
msgmni has been set to 470
alg: No test for stdrng (krng)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
OMAP DSS rev 2.0
OMAP DISPC rev 3.0
OMAP VENC rev 2
Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
serial8250.0: ttyS0 at MMIO 0x4806a000 (irq = 72) is a ST16654
serial8250.1: ttyS1 at MMIO 0x4806c000 (irq = 73) is a ST16654
serial8250.2: ttyS2 at MMIO 0x49020000 (irq = 74) is a ST16654
console [ttyS2] enabled
brd: module loaded
loop: module loaded
i2c /dev entries driver
smsc911x: Driver version 2008-10-21.
smsc911x-mdio: probed
eth0: attached PHY driver [Generic PHY] (mii_bus:phy_addr=0:01, irq=-1)
net eth0: MAC Address: 00:15:c9:28:c5:12
smsc911x: Driver version 2008-10-21.
usbcore: registered new interface driver asix
usbcore: registered new interface driver cdc_ether
omap2-nand driver initializing
NAND device: Manufacturer ID: 0x2c, Chip ID: 0xba (Micron NAND 256MiB 1,8V
16-bit)
cmdlinepart partition parsing not available
Creating 5 MTD partitions on "omap2-nand":
0x000000000000-0x000000080000 : "xloader"
0x000000080000-0x000000240000 : "uboot"
0x000000240000-0x000000280000 : "uboot environment"
0x000000280000-0x000000680000 : "linux"
0x000000680000-0x000010000000 : "rootfs"
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci-omap ehci-omap.0: OMAP-EHCI Host Controller
ehci-omap ehci-omap.0: new USB bus registered, assigned bus number 2
ehci-omap ehci-omap.0: irq 77, io mem 0x48064800
ehci-omap ehci-omap.0: USB 2.0 started, EHCI 1.00
usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: OMAP-EHCI Host Controller
usb usb2: Manufacturer: Linux 2.6.31-omap1 ehci_hcd
usb usb2: SerialNumber: ehci-omap.0
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 3 ports detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
udc: OMAP UDC driver, version: 4 October 2004 (iso) (dma)
mice: PS/2 mouse device common for all mice
twl4030_rtc twl4030_rtc: rtc core: registered twl4030_rtc as rtc0
OMAP Watchdog Timer Rev 0x31: initial timeout 60 sec
Bluetooth: HCI UART driver ver 2.2
Bluetooth: HCI H4 protocol initialized
Bluetooth: HCI BCSP protocol initialized
Bluetooth: HCILL protocol initialized
cpuidle: using governor ladder
cpuidle: using governor menu
mmci-omap-hs mmci-omap-hs.0: Failed to get debounce clock
mmci-omap-hs mmci-omap-hs.1: Failed to get debounce clock
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
Advanced Linux Sound Architecture Driver Version 1.0.20.
usbcore: registered new interface driver snd-usb-audio
No device for DAI twl4030
No device for DAI twl4030 Voice
No device for DAI omap-mcbsp-dai-0
No device for DAI omap-mcbsp-dai-1
No device for DAI omap-mcbsp-dai-2
No device for DAI omap-mcbsp-dai-3
No device for DAI omap-mcbsp-dai-4
overo SoC init
TWL4030 Audio Codec init
asoc: twl4030 <-> omap-mcbsp-dai-0 mapping ok
ALSA device list:
#0: overo (twl4030)
oprofile: using arm/armv7
TCP cubic registered
NET: Registered protocol family 17
NET: Registered protocol family 15
Bluetooth: L2CAP ver 2.13
Bluetooth: L2CAP socket layer initialized
Bluetooth: SCO (Voice Link) ver 0.6
Bluetooth: SCO socket layer initialized
Bluetooth: RFCOMM TTY layer initialized
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM ver 1.11
Bluetooth: BNEP (Ethernet Emulation) ver 1.3
Bluetooth: BNEP filters: protocol multicast
Bluetooth: HIDP (Human Interface Emulation) ver 1.2
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
ThumbEE CPU extension supported.
Power Management for TI OMAP3.
VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 1
fbcvt: 1024x768@60: CVT Name - .786M3-R
Console: switching to colour frame buffer device 60x34
omapdss DPI: Could not find exact pixel clock. Requested 9200 kHz, got 9094
kHz
regulator_init_complete: incomplete constraints, leaving VDVI on
regulator_init_complete: incomplete constraints, leaving VDAC on
twl4030_rtc twl4030_rtc: setting system clock to 2009-03-27 10:51:11 UTC
(1238151071)
Waiting for root device /dev/mmcblk0p2...
mmc0: host does not support reading read-only switch. assuming write-enable.
mmc0: new high speed SDHC card at address aaaa
mmcblk0: mmc0:aaaa SU04G 3.69 GiB
mmcblk0: p1 p2
kjournald starting. Commit interval 5 seconds
EXT3 FS on mmcblk0p2, internal journal
EXT3-fs: mounted filesystem with writeback data mode.
VFS: Mounted root (ext3 filesystem) on device 179:2.
Freeing init memory: 924K
INIT: version 2.86 booting
Please wait: booting...
Starting udev
ads7846 spi1.0: touchscreen, irq 274
input: ADS7846 Touchscreen as
/devices/platform/omap2_mcspi.1/spi1.0/input/input0
Populating dev cache
Remounting root file system...
Undefined users:
> pulse
Skipping /etc/default/volatiles/04_pulse
Undefined users:
> haldaemon
Skipping /etc/default/volatiles/99_hal
ALSA: Restoring mixer settings...
Configuring network interfaces... /usr/sbin/alsactl: parse:1639: Unable to
open file '/usr/share/alsa/init/00main': No such file or directory
/usr/sbin/alsactl: set_control:1256: failed to obtain info for control #16
(No such file or directory)
/usr/sbin/alsactl: set_control:1256: failed to obtain info for control #17
(No such file or directory)
/usr/sbin/alsactl: set_control:1256: failed to obtain info for control #22
(No such file or directory)
/usr/sbin/alsactl: set_control:1256: failed to obtain info for control #23
(No such file or directory)
/usr/sbin/alsactl: set_control:1256: failed to obtain info for control #24
(No such file or directory)
/usr/sbin/alsactl: set_control:1256: failed to obtain info for control #25
(No such file or directory)
/usr/sbin/alsactl: set_control:1256: failed to obtain info for control #26
(No such file or directory)
/usr/sbin/alsactl: set_control:1256: failed to obtain info for control #27
(No such file or directory)
/usr/sbin/alsactl: set_control:1256: failed to obtain info for control #28
(No such file or directory)
done.
Starting portmap daemon: portmap.
Unknown HZ value! (67) Assume 100.
net.ipv4.conf.default.rp_filter = 1
net.ipv4.conf.all.rp_filter = 1
Tue Oct 13 02:19:00 BST 2009
Checking for built-in Bluetooth: yes
Configuring angstrom-zeroconf-audio
Configuring avahi-daemon
System startup links for /etc/init.d/avahi-daemon already exist.
Configuring libnss-mdns
Configuring gdk-pixbuf-loader-png
Configuring pango-module-basic-fc
Configuring ttf-dejavu-common
Configuring openssh-sshd
Adding system startup for /etc/init.d/sshd.
Configuring sudo
Configuring connman-gnome
Configuring ttf-dejavu-sans-mono
Configuring hicolor-icon-theme
Configuring pulseaudio-server
addgroup: pulse: group already in use
Undefined users:
> haldaemon
Skipping /etc/default/volatiles/99_hal
postinst script returned status 1
Configuring ppp-dialin
Configuring avahi-autoipd
Configuring ntpdate
grep: /etc/cron/crontabs/root: No such file or directory
adding crontab
update-rc.d: /etc/init.d/busybox-cron: file does not exist
Adding system startup for /etc/init.d/ntpdate.
Configuring gdk-pixbuf-loader-xpm
Configuring angstrom-libc-fixup-hack
Configuring update-modules
Configuring midori
Configuring pango-module-basic-x
Configuring rosetta
Configuring ttf-dejavu-sans
Configuring omap3-sgx-modules
Configuring dbus
System startup links for /etc/init.d/dbus-1 already exist.
Configuring gdk-pixbuf-loader-jpeg
Configuring gdk-pixbuf-loader-gif
Configuring ppp
Configuring policykit
chmod: cannot access `/var/run/PolicyKit': No such file or directory
Configuring locale-base-en-us
Configuring hal
NET: Registered protocol family 10
Collected errors:
* ERROR: pulseaudio-server.postinst returned 1
INIT: Entering runlevel: 5
Starting system message bus: Unknown username "system" in message bus
configuration file
dbus.
Starting Hardware abstraction layer hald
Starting Connection Manager
net eth0: SMSC911x/921x identified at 0xd08c4000, IRQ: 336
Starting OpenBSD Secure Shell server: sshd
generating ssh RSA key...
generating ssh DSA key...
done.
Starting advanced power management daemon: No APM support in kernel
(failed.)
Starting ntpd: done
Starting syslogd/klogd: done
* Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon
[ ok ]
Starting Bluetooth subsystem:
Initialization timed out.
Running ntpdate to synchronize clockError : Name or service not known
.
Starting GPE display manager: gpe-dm
.-------.
| | .-.
| | |-----.-----.-----.| | .----..-----.-----.
| | | __ | ---'| '--.| .-'| | |
| | | | | |--- || --'| | | ' | | | |
'---'---'--'--'--. |-----''----''--' '-----'-'-'-'
-' |
'---'
The Angstrom Distribution overo ttyS2
Angstrom 2009.X-test-20091013 overo ttyS2
overo login: root
root@overo:~# cd /
root@overo:/# £tصb$U
@ @ @D¨±` @ @à
Texas Instruments X-Loader 1.4.2 (Feb 19 2009 - 12:01:24)
Reading boot sector
Loading u-boot.bin from mmc
U-Boot 2009.08 (Oct 12 2009 - 18:16:02)
OMAP3530-GP ES3.1, CPU-OPP2 L3-165MHz
Gumstix Overo board + LPDDR/NAND
I2C: ready
DRAM: 256 MB
NAND: 256 MiB
In: serial
Out: serial
Err: serial
Die ID #538c00040000000004035c1401005016
Net: smc911x-0
Hit any key to stop autoboot: 5 4 £tصb$U
@ @ @D¨±` @ Àà
Texas Instruments X-Loader 1.4.2 (Feb 19 2009 - 12:01:24)
Reading boot sector
Loading u-boot.bin from mmc
U-Boot 2009.08 (Oct 12 2009 - 18:16:02)
OMAP3530-GP ES3.1, CPU-OPP2 L3-165MHz
Gumstix Overo board + LPDDR/NAND
I2C: ready
DRAM: 256 MB
NAND: 256 MiB
In: serial
Out: serial
Err: serial
Die ID #538c00040000000004035c1401005016
Net: smc911x-0
Hit any key to stop autoboot: 5 4 3 2 1 0
mmc1 is available
reading boot.scr
** Unable to read "boot.scr" from mmc 0:1 **
reading uImage
3075240 bytes read
Booting from mmc ...
## Booting kernel from Legacy Image at 82000000 ...
Image Name: Angstrom/2.6.31/overo
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 3075176 Bytes = 2.9 MB
Load Address: 80008000
Entry Point: 80008000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK
Starting kernel ...
Uncompressing
Linux...........................................................................................................................................................................................................
done, booting the kernel.
Linux version 2.6.31-omap1 (sakoman@otto) (gcc version 4.3.3 (GCC) ) #1 Mon
Oct 12 18:25:39 PDT 2009
CPU: ARMv7 Processor [411fc083] revision 3 (ARMv7), cr=10c53c7f
CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache
Machine: Gumstix Overo
Memory policy: ECC disabled, Data cache writeback
OMAP3430 ES3.1
SRAM: Mapped pa 0x40200000 to va 0xe3000000 size: 0x100000
Reserving 12582912 bytes SDRAM for VRAM
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024
Kernel command line: console=ttyS2,115200n8 vram=12M
omapfb.mode=dvi:1024x768MR-16@60 omapfb.debug=y omapdss.def_disp=lcd43
root=/dev/mmcblk0p2 rw rootfstype=ext3 rootwait
PID hash table entries: 1024 (order: 10, 4096 bytes)
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 128MB 128MB = 256MB total
Memory: 240640KB available (5052K code, 575K data, 924K init, 0K highmem)
NR_IRQS:402
Clocking rate (Crystal/Core/MPU): 26.0/332/500 MHz
Reprogramming SDRC clock to 332000000 Hz
GPMC revision 5.0
IRQ: Found an INTC at 0xd8200000 (revision 4.0) with 96 interrupts
Total of 96 interrupts on 1 active controller
OMAP34xx GPIO hardware version 2.5
OMAP clockevent source: GPTIMER1 at 32768 Hz
Console: colour dummy device 80x30
Calibrating delay loop... 499.92 BogoMIPS (lpj=1949696)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
regulator: core version 0.5
NET: Registered protocol family 16
Found NAND on CS0
Registering NAND on CS0
OMAP DMA hardware revision 4.0
bio: create slab <bio-0> at 0
i2c_omap i2c_omap.1: bus 1 rev3.12 at 2600 kHz
twl4030: PIH (irq 7) chaining IRQs 368..375
twl4030: power (irq 373) chaining IRQs 376..383
twl4030: gpio (irq 368) chaining IRQs 384..401
regulator: VMMC1: 1850 <--> 3150 mV normal standby
regulator: VDAC: 1800 mV normal standby
regulator: VUSB1V5: 1500 mV normal standby
regulator: VUSB1V8: 1800 mV normal standby
regulator: VUSB3V1: 3100 mV normal standby
regulator: VPLL2: 1800 mV normal standby
i2c_omap i2c_omap.3: bus 3 rev3.12 at 400 kHz
SCSI subsystem initialized
twl4030_usb twl4030_usb: Initialized TWL4030 USB module
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
Bluetooth: Core ver 2.15
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
cfg80211: Using static regulatory domain info
cfg80211: Regulatory domain: US
(start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
(2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2700 mBm)
(5170000 KHz - 5190000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
(5190000 KHz - 5210000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
(5210000 KHz - 5230000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
(5230000 KHz - 5330000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
(5735000 KHz - 5835000 KHz @ 40000 KHz), (600 mBi, 3000 mBm)
cfg80211: Calling CRDA for country: US
musb_hdrc: version 6.0, musb-dma, host, debug=0
musb_hdrc: USB Host mode controller at d80ab000 using DMA, IRQ 92
musb_hdrc musb_hdrc: MUSB HDRC host driver
musb_hdrc musb_hdrc: new USB bus registered, assigned bus number 1
usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: MUSB HDRC host driver
usb usb1: Manufacturer: Linux 2.6.31-omap1 musb-hcd
usb usb1: SerialNumber: musb_hdrc
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
NET: Registered protocol family 2
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP reno registered
NET: Registered protocol family 1
VFS: Disk quotas dquot_6.5.2
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
JFFS2 version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
msgmni has been set to 470
alg: No test for stdrng (krng)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
OMAP DSS rev 2.0
OMAP DISPC rev 3.0
OMAP VENC rev 2
Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
serial8250.0: ttyS0 at MMIO 0x4806a000 (irq = 72) is a ST16654
serial8250.1: ttyS1 at MMIO 0x4806c000 (irq = 73) is a ST16654
serial8250.2: ttyS2 at MMIO 0x49020000 (irq = 74) is a ST16654
console [ttyS2] enabled
brd: module loaded
loop: module loaded
i2c /dev entries driver
smsc911x: Driver version 2008-10-21.
smsc911x-mdio: probed
eth0: attached PHY driver [Generic PHY] (mii_bus:phy_addr=0:01, irq=-1)
net eth0: MAC Address: 00:15:c9:28:c5:12
smsc911x: Driver version 2008-10-21.
usbcore: registered new interface driver asix
usbcore: registered new interface driver cdc_ether
omap2-nand driver initializing
NAND device: Manufacturer ID: 0x2c, Chip ID: 0xba (Micron NAND 256MiB 1,8V
16-bit)
cmdlinepart partition parsing not available
Creating 5 MTD partitions on "omap2-nand":
0x000000000000-0x000000080000 : "xloader"
0x000000080000-0x000000240000 : "uboot"
0x000000240000-0x000000280000 : "uboot environment"
0x000000280000-0x000000680000 : "linux"
0x000000680000-0x000010000000 : "rootfs"
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci-omap ehci-omap.0: OMAP-EHCI Host Controller
ehci-omap ehci-omap.0: new USB bus registered, assigned bus number 2
ehci-omap ehci-omap.0: irq 77, io mem 0x48064800
ehci-omap ehci-omap.0: USB 2.0 started, EHCI 1.00
usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: OMAP-EHCI Host Controller
usb usb2: Manufacturer: Linux 2.6.31-omap1 ehci_hcd
usb usb2: SerialNumber: ehci-omap.0
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 3 ports detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
udc: OMAP UDC driver, version: 4 October 2004 (iso) (dma)
mice: PS/2 mouse device common for all mice
twl4030_rtc twl4030_rtc: rtc core: registered twl4030_rtc as rtc0
OMAP Watchdog Timer Rev 0x31: initial timeout 60 sec
Bluetooth: HCI UART driver ver 2.2
Bluetooth: HCI H4 protocol initialized
Bluetooth: HCI BCSP protocol initialized
Bluetooth: HCILL protocol initialized
cpuidle: using governor ladder
cpuidle: using governor menu
mmci-omap-hs mmci-omap-hs.0: Failed to get debounce clock
mmci-omap-hs mmci-omap-hs.1: Failed to get debounce clock
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
Advanced Linux Sound Architecture Driver Version 1.0.20.
usbcore: registered new interface driver snd-usb-audio
No device for DAI twl4030
No device for DAI twl4030 Voice
No device for DAI omap-mcbsp-dai-0
No device for DAI omap-mcbsp-dai-1
No device for DAI omap-mcbsp-dai-2
No device for DAI omap-mcbsp-dai-3
No device for DAI omap-mcbsp-dai-4
overo SoC init
TWL4030 Audio Codec init
asoc: twl4030 <-> omap-mcbsp-dai-0 mapping ok
ALSA device list:
#0: overo (twl4030)
oprofile: using arm/armv7
TCP cubic registered
NET: Registered protocol family 17
NET: Registered protocol family 15
Bluetooth: L2CAP ver 2.13
Bluetooth: L2CAP socket layer initialized
Bluetooth: SCO (Voice Link) ver 0.6
Bluetooth: SCO socket layer initialized
Bluetooth: RFCOMM TTY layer initialized
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM ver 1.11
Bluetooth: BNEP (Ethernet Emulation) ver 1.3
Bluetooth: BNEP filters: protocol multicast
Bluetooth: HIDP (Human Interface Emulation) ver 1.2
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
ThumbEE CPU extension supported.
Power Management for TI OMAP3.
VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 1
fbcvt: 1024x768@60: CVT Name - .786M3-R
Console: switching to colour frame buffer device 60x34
omapdss DPI: Could not find exact pixel clock. Requested 9200 kHz, got 9094
kHz
regulator_init_complete: incomplete constraints, leaving VDVI on
regulator_init_complete: incomplete constraints, leaving VDAC on
twl4030_rtc twl4030_rtc: setting system clock to 2009-10-13 05:34:32 UTC
(1255412072)
Waiting for root device /dev/mmcblk0p2...
mmc0: host does not support reading read-only switch. assuming write-enable.
mmc0: new high speed SDHC card at address aaaa
mmcblk0: mmc0:aaaa SU04G 3.69 GiB
mmcblk0: p1 p2
kjournald starting. Commit interval 5 seconds
EXT3 FS on mmcblk0p2, internal journal
EXT3-fs: mounted filesystem with writeback data mode.
VFS: Mounted root (ext3 filesystem) on device 179:2.
Freeing init memory: 924K
INIT: version 2.86 booting
Please wait: booting...
Starting udev
ads7846 spi1.0: touchscreen, irq 274
input: ADS7846 Touchscreen as
/devices/platform/omap2_mcspi.1/spi1.0/input/input0
Populating dev cache
Remounting root file system...
Undefined users:
> pulse
Skipping /etc/default/volatiles/04_pulse
Undefined users:
> haldaemon
Skipping /etc/default/volatiles/99_hal
ALSA: Restoring mixer settings...
Configuring network interfaces... /usr/sbin/alsactl: parse:1639: Unable to
open file '/usr/share/alsa/init/00main': No such file or directory
/usr/sbin/alsactl: set_control:1256: failed to obtain info for control #16
(No such file or directory)
/usr/sbin/alsactl: set_control:1256: failed to obtain info for control #17
(No such file or directory)
/usr/sbin/alsactl: set_control:1256: failed to obtain info for control #22
(No such file or directory)
/usr/sbin/alsactl: set_control:1256: failed to obtain info for control #23
(No such file or directory)
/usr/sbin/alsactl: set_control:1256: failed to obtain info for control #24
(No such file or directory)
/usr/sbin/alsactl: set_control:1256: failed to obtain info for control #25
(No such file or directory)
/usr/sbin/alsactl: set_control:1256: failed to obtain info for control #26
(No such file or directory)
/usr/sbin/alsactl: set_control:1256: failed to obtain info for control #27
(No such file or directory)
/usr/sbin/alsactl: set_control:1256: failed to obtain info for control #28
(No such file or directory)
done.
Starting portmap daemon: portmap.
Unknown HZ value! (67) Assume 100.
net.ipv4.conf.default.rp_filter = 1
net.ipv4.conf.all.rp_filter = 1
Checking for built-in Bluetooth: yes
Configuring angstrom-zeroconf-audio
Configuring avahi-daemon
System startup links for /etc/init.d/avahi-daemon already exist.
Configuring libnss-mdns
Configuring gdk-pixbuf-loader-png
Configuring pango-module-basic-fc
Configuring ttf-dejavu-common
Configuring openssh-sshd
Adding system startup for /etc/init.d/sshd.
Configuring sudo
Configuring connman-gnome
Configuring ttf-dejavu-sans-mono
Configuring hicolor-icon-theme
Configuring pulseaudio-server
addgroup: pulse: group already in use
Undefined users:
> haldaemon
Skipping /etc/default/volatiles/99_hal
postinst script returned status 1
Configuring ppp-dialin
Configuring avahi-autoipd
Configuring ntpdate
grep: /etc/cron/crontabs/root: No such file or directory
adding crontab
update-rc.d: /etc/init.d/busybox-cron: file does not exist
Adding system startup for /etc/init.d/ntpdate.
Configuring gdk-pixbuf-loader-xpm
Configuring angstrom-libc-fixup-hack
Configuring update-modules
Configuring midori
Configuring pango-module-basic-x
Configuring rosetta
Configuring ttf-dejavu-sans
Configuring omap3-sgx-modules
Configuring dbus
System startup links for /etc/init.d/dbus-1 already exist.
Configuring gdk-pixbuf-loader-jpeg
Configuring gdk-pixbuf-loader-gif
Configuring ppp
Configuring policykit
chmod: cannot access `/var/run/PolicyKit': No such file or directory
Configuring locale-base-en-us
Configuring hal
NET: Registered protocol family 10
Collected errors:
* ERROR: pulseaudio-server.postinst returned 1
INIT: Entering runlevel: 5
Starting system message bus: Unknown username "system" in message bus
configuration file
dbus.
Starting Hardware abstraction layer hald
Starting Connection Manager
net eth0: SMSC911x/921x identified at 0xd08c4000, IRQ: 336
Starting OpenBSD Secure Shell server: sshd
generating ssh RSA key...
generating ssh DSA key...
done.
Starting advanced power management daemon: No APM support in kernel
(failed.)
Starting ntpd: done
Starting syslogd/klogd: done
* Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon
[ ok ]
Starting Bluetooth subsystem:
Initialization timed out.
Running ntpdate to synchronize clockError : Name or service not known
.
Starting GPE display manager: gpe-dm
.-------.
| | .-.
| | |-----.-----.-----.| | .----..-----.-----.
| | | __ | ---'| '--.| .-'| | |
| | | | | |--- || --'| | | ' | | | |
'---'---'--'--'--. |-----''----''--' '-----'-'-'-'
-' |
'---'
The Angstrom Distribution overo ttyS2
Angstrom 2009.X-test-20091013 overo ttyS2
overo login: root
root@overo:~# cd /
root@overo:/#
--
View this message in context: http://old.nabble.com/overo_palmtop_200910121635-image-%2Btouch-screen-problem--log-tp26545640p26545640.html
Sent from the Gumstix mailing list archive at Nabble.com.
|