Menu
▾
▴
Re: [Gumstix-users] OpenEmbedded Bitbake image for connex
|
From: Xiang Z. <xz...@tc...> - 2008-06-26 21:18:57
|
Hi Crhis, You rock, That 's it, I can login in now, Thanks a lot. Xiang 2008/6/26 Chris Dollar <chr...@gm...>: > You will probably need to rebuild your kernel and reflash it. You might even > need to rebuild the entire filesystem and flash it as well, but lets start > with the kernel. So from where you installed gumstix-oe run 'bitbake -c > rebuild gumstix-kernel'. This will build you a new uImage, which you need to > flash to your gumstix. Give that a try and let us know if it does/doesn't > work for you. > > Chris > On Thu, Jun 26, 2008 at 2:47 PM, XiangZ <xz...@tc...> wrote: >> >> Hi Chris, >> >> Thanks for the help. After your advice I have followed that list and did >> again. I have Run "sudo dpkg-reconfigure dash" and answered No. (reboot >> the >> desktop and rebuild the image.) >> After I reload the image and kernel , it still hanging at the same place. >> >> did I missing some steps? >> >> >> Xiang >> >> >> >> Chris Dollar wrote: >> > >> > Check that you don't have /bin/sh linked to /bin/dash as is noted on >> > this >> > page >> > >> > http://www.gumstix.net/Software/view/Getting-started/Setting-up-a-build-environment/111.html. >> > Having the dash link will cause it to hang at 'freeing init memory'. >> > >> > Chris >> > >> > On Thu, Jun 26, 2008 at 1:15 PM, XiangZ <xz...@tc...> wrote: >> > >> >> >> >> Hello, >> >> >> >> I am using gumstix connex400xm. After I using OpenEmbedded bitbake to >> >> make >> >> a >> >> new image and kernel. I used serial connection to upload both on to >> >> the >> >> gumstix , then it just won't reboot. It is doing something , but then >> >> hanging before the login. >> >> >> >> I was following procedure on the openembedded site to do the rebuild >> >> and >> >> uploading. I have tried a few time , but it still the same. I can use >> >> "ls >> >> " >> >> to check the file system. >> >> >> >> I want to know if anyone had similar problem ? >> >> >> >> Here is the message: >> >> >> >> >> >> U-Boot 1.2.0 (Aug 30 2007 - 13:21:47) - 400 MHz - 1513 >> >> >> >> *** Welcome to Gumstix *** >> >> >> >> DRAM: 64 MB >> >> Flash: 16 MB >> >> Using default environment >> >> >> >> SMC91C1111-0 >> >> Net: SMC91C1111-0 >> >> Hit any key to stop autoboot: 0 >> >> Instruction Cache is ON >> >> Copying kernel to 0xa2000000 from 0x00f00000 (length 0x00100000)...done >> >> ## Booting image at a2000000 ... >> >> Image Name: Angstrom/2.6.21/gumstix-custom-c >> >> Image Type: ARM Linux Kernel Image (uncompressed) >> >> Data Size: 1038444 Bytes = 1014.1 kB >> >> Load Address: a0008000 >> >> Entry Point: a0008000 >> >> OK >> >> >> >> Starting kernel ... >> >> >> >> Linux version 2.6.21 (xzhou@XiangZhou) (gcc version 4.1.2) #1 PREEMPT >> >> Sat >> >> Jun 21 22:08:52 IST 2008 >> >> CPU: XScale-PXA255 [69052d06] revision 6 (ARMv5TE), cr=0000397f >> >> Machine: The Gumstix Platform >> >> Memory policy: ECC disabled, Data cache writeback >> >> Memory clock: 99.53MHz (*27) >> >> Run Mode clock: 398.13MHz (*4) >> >> Turbo Mode clock: 398.13MHz (*1.0, inactive) >> >> CPU0: D VIVT undefined 5 cache >> >> CPU0: I cache: 32768 bytes, associativity 32, 32 byte lines, 32 sets >> >> CPU0: D cache: 32768 bytes, associativity 32, 32 byte lines, 32 sets >> >> Built 1 zonelists. Total pages: 16256 >> >> Kernel command line: console=ttyS0,115200n8 root=1f01 rootfstype=jffs2 >> >> reboot=cold,hard >> >> PID hash table entries: 256 (order: 8, 1024 bytes) >> >> Console: colour dummy device 80x30 >> >> Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) >> >> Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) >> >> Memory: 64MB = 64MB total >> >> Memory: 62720KB available (1872K code, 193K data, 144K init) >> >> Mount-cache hash table entries: 512 >> >> CPU: Testing write buffer coherency: ok >> >> NET: Registered protocol family 16 >> >> Time: pxa_timer clocksource has been installed. >> >> NET: Registered protocol family 2 >> >> IP route cache hash table entries: 1024 (order: 0, 4096 bytes) >> >> TCP established hash table entries: 2048 (order: 2, 16384 bytes) >> >> TCP bind hash table entries: 2048 (order: 1, 8192 bytes) >> >> TCP: Hash tables configured (established 2048 bind 2048) >> >> TCP reno registered >> >> JFFS2 version 2.2. (NAND) (SUMMARY) (C) 2001-2006 Red Hat, Inc. >> >> io scheduler noop registered >> >> io scheduler cfq registered (default) >> >> Console: switching to colour frame buffer device 80x24 >> >> pxa2xx-uart.0: ttyS0 at MMIO 0x40100000 (irq = 15) is a FFUART >> >> pxa2xx-uart.1: ttyS1 at MMIO 0x40200000 (irq = 14) is a BTUART >> >> pxa2xx-uart.2: ttyS2 at MMIO 0x40700000 (irq = 13) is a STUART >> >> pxa2xx-uart.3: ttyS3 at MMIO 0x41600000 (irq = 0) is a HWUART >> >> Probing Gumstix Flash ROM at physical address 0x00000000 (16-bit >> >> bankwidth) >> >> Gumstix Flash ROM: Found 1 x16 devices at 0x0 in 16-bit bank >> >> Intel/Sharp Extended Query Table at 0x0031 >> >> Using buffer write method >> >> cfi_cmdset_0001: Erase suspend on write enabled >> >> Using static partitions on Gumstix Flash ROM >> >> Creating 3 MTD partitions on "Gumstix Flash ROM": >> >> 0x00000000-0x00040000 : "Bootloader" >> >> 0x00040000-0x00f00000 : "RootFS" >> >> 0x00f00000-0x01000000 : "Kernel" >> >> TCP cubic registered >> >> NET: Registered protocol family 1 >> >> NET: Registered protocol family 17 >> >> XScale DSP coprocessor detected. >> >> VFS: Mounted root (jffs2 filesystem). >> >> Freeing init memory: 144K >> >> >> >> >> >> >> >> >> >> -- >> >> View this message in context: >> >> >> >> http://www.nabble.com/OpenEmbedded-Bitbake-image-for-connex-tp18141258p18141258.html >> >> Sent from the Gumstix mailing list archive at Nabble.com. >> >> >> >> >> >> >> >> ------------------------------------------------------------------------- >> >> Check out the new SourceForge.net Marketplace. >> >> It's the best place to buy or sell services for >> >> just about anything Open Source. >> >> http://sourceforge.net/services/buy/index.php >> >> _______________________________________________ >> >> gumstix-users mailing list >> >> gum...@li... >> >> https://lists.sourceforge.net/lists/listinfo/gumstix-users >> >> >> > >> > >> > ------------------------------------------------------------------------- >> > Check out the new SourceForge.net Marketplace. >> > It's the best place to buy or sell services for >> > just about anything Open Source. >> > http://sourceforge.net/services/buy/index.php >> > _______________________________________________ >> > gumstix-users mailing list >> > gum...@li... >> > https://lists.sourceforge.net/lists/listinfo/gumstix-users >> > >> > >> >> -- >> View this message in context: >> http://www.nabble.com/OpenEmbedded-Bitbake-image-for-connex-tp18141258p18142363.html >> Sent from the Gumstix mailing list archive at Nabble.com. >> >> >> ------------------------------------------------------------------------- >> Check out the new SourceForge.net Marketplace. >> It's the best place to buy or sell services for >> just about anything Open Source. >> http://sourceforge.net/services/buy/index.php >> _______________________________________________ >> gumstix-users mailing list >> gum...@li... >> https://lists.sourceforge.net/lists/listinfo/gumstix-users > > > ------------------------------------------------------------------------- > Check out the new SourceForge.net Marketplace. > It's the best place to buy or sell services for > just about anything Open Source. > http://sourceforge.net/services/buy/index.php > _______________________________________________ > gumstix-users mailing list > gum...@li... > https://lists.sourceforge.net/lists/listinfo/gumstix-users > > |