Re: [Gumstix-users] Mounting CF card on Verdex net-CF card fails

SourceForge Headquarters 225 Broadway Suite 1600 San Diego, CA 92101 +1 (858) 454-5900

Hi Ray,
I just installed an mmc card in a Verdex and it seems to work. Here is a
link to the instructions for the CF card which are almost identical:
http://www.gumstix.net/Documentation/view/User-how-to-s/Installing-packages-to-CF-memory-cards/109.html

Don't know whether you had found these. I can't remember whether i mounted
it is SDA or HDA, but I did mount it as vfat, and made sure the card was
formatted before I mounted it.

Good luck,
Borre

On Thu, Jun 5, 2008 at 12:03 AM, Ray Johnston <Ray...@ar...>
wrote:

>  Hi all,
>
> I am able to see the CF card with the Uboot (following instructions
> for flashing a new image), and from the ssh prompt I am able to see
> the partition using:
>
>     fdisk /dev/hda
>
> and the 'p' shows the partition (I've tried FAT32, FAT16 and HPFS/NTFS)
> but:
>
>     mount -t autofs /dev/hda1 /mnt/cf
>
> fails with the message:
>      mount: Mounting /dev/hda1 on /mnt/cf failed: No such device
>
> Also "mount -a" doesn't mount the CF card (but doesn't issue any message
> as the explicit "mount" above does). My /etc/fstab has:
>
> /dev/mtdblock1  /               jffs2   rw,noatime              0       1
> proc            /proc           proc    defaults                0       0
> sysfs           /sys            sysfs   defaults                0       0
> # devpts is noauto because it needs to mount *after* udev starts
> devpts          /dev/pts        devpts  gid=5,mode=620,noauto   0       0
> tmpfs           /tmp            tmpfs   mode=1777               0       0
> /dev/mmcblk0p1  /mnt/mmc        vfat    sync,noauto             0       0
> /dev/sda1       /mnt/usb        vfat    sync,noauto             0       0
> /dev/hda1       /mnt/cf         vfat    sync,noauto             0       0
>
> and 'lsmod' shows:
>
> Module                  Size  Used by
> vfat                    9920  0
> fat                    45980  1 vfat
> nls_base                6400  2 vfat,fat
> ipv6                  248416  12
> mcf25                 217136  0
> cfio                    5120  1 mcf25
> ide_disk               13216  0
> pata_pcmcia             9696  0
> libata                 94548  1 pata_pcmcia
> scsi_mod               84772  1 libata
> ide_cs                  8960  1
> ide_core               81780  2 ide_disk,ide_cs
> usblp                  11872  0
> ohci_hcd               19620  0
> usbcore               113340  3 usblp,ohci_hcd
> pxa2xx_cs               3044  3
> pxa2xx_core            10368  1 pxa2xx_cs
> pcmcia                 25064  3 cfio,pata_pcmcia,ide_cs
> pcmcia_core            30576  6
> mcf25,cfio,pata_pcmcia,ide_cs,pxa2xx_core,pcmcia
> firmware_class          7520  1 pcmcia
> smc91x                 16104  0
> mii                     4736  1 smc91x
> gumstix_smc91x          2816  1 smc91x
> unix                   22292  16
>
>
> and ls -l /mnt shows:
>
> drwxrwxr-x    2 root     root            0 Aug 22  2007 cf
> drwxrwxr-x    2 root     root            0 Aug 22  2007 mmc
> drwxrwxr-x    2 root     root            0 Aug 22  2007 nfs
> drwxrwxr-x    2 root     root            0 Aug 22  2007 usb
>
> which looks like an acceptable mount point.
>
> Any suggestions?
>
> Note, I've also attached my 'dmesg' output.
>
> Regards,
> Ray Johnston
>  ------------------------------
>
>   ------------------------------
>
> Linux version 2.6.21gum (glachac@centos4_1.tethermedia.net) (gcc version 4.1.1) #1 Wed Aug 22 07:19:27 EDT 2007
> CPU: XScale-PXA270 [69054117] revision 7 (ARMv5TE), cr=0000397f
> Machine: The Gumstix Platform
> Memory policy: ECC disabled, Data cache writeback
> On node 0 totalpages: 32768
>   DMA zone: 256 pages used for memmap
>   DMA zone: 0 pages reserved
>   DMA zone: 32512 pages, LIFO batch:7
>   Normal zone: 0 pages used for memmap
> Run Mode clock: 208.00MHz (*16)
> Turbo Mode clock: 624.00MHz (*3.0, active)
> Memory clock: 104.00MHz (/2)
> System bus clock: 104.00MHz
> CPU0: D VIVT undefined 5 cache
> CPU0: I cache: 32768 bytes, associativity 32, 32 byte lines, 32 sets
> CPU0: D cache: 32768 bytes, associativity 32, 32 byte lines, 32 sets
> Built 1 zonelists.  Total pages: 32512
> Kernel command line: console=ttyS0,115200n8 root=1f01 rootfstype=jffs2 reboot=cold,hard
> PID hash table entries: 512 (order: 9, 2048 bytes)
> Console: colour dummy device 80x30
> Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
> Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
> Memory: 128MB = 128MB total
> Memory: 127744KB available (1748K code, 192K data, 132K init)
> Calibrating delay loop... 622.59 BogoMIPS (lpj=3112960)
> Mount-cache hash table entries: 512
> CPU: Testing write buffer coherency: ok
> NET: Registered protocol family 16
> NET: Registered protocol family 2
> Time: pxa_timer clocksource has been installed.
> IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
> TCP established hash table entries: 4096 (order: 3, 32768 bytes)
> TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
> TCP: Hash tables configured (established 4096 bind 4096)
> TCP reno registered
> JFFS2 version 2.2. (NAND) (SUMMARY)  (C) 2001-2006 Red Hat, Inc.
> io scheduler noop registered
> io scheduler cfq registered (default)
> Console: switching to colour frame buffer device 80x24
> pxa2xx-uart.0: ttyS0 at MMIO 0x40100000 (irq = 22) is a FFUART
> pxa2xx-uart.1: ttyS1 at MMIO 0x40200000 (irq = 21) is a BTUART
> pxa2xx-uart.2: ttyS2 at MMIO 0x40700000 (irq = 20) is a STUART
> Probing Gumstix Flash ROM at physical address 0x00000000 (16-bit bankwidth)
> Gumstix Flash ROM: Found 1 x16 devices at 0x0 in 16-bit bank
> Gumstix Flash ROM: Found an alias at 0x2000000 for the chip at 0x0
>  Intel/Sharp Extended Query Table at 0x010A
>  Intel/Sharp Extended Query Table at 0x010A
>  Intel/Sharp Extended Query Table at 0x010A
>  Intel/Sharp Extended Query Table at 0x010A
>  Intel/Sharp Extended Query Table at 0x010A
> Using buffer write method
> cfi_cmdset_0001: Erase suspend on write enabled
> erase region 0: offset=0x0,size=0x20000,blocks=255
> erase region 1: offset=0x1fe0000,size=0x8000,blocks=4
> Using static partitions on Gumstix Flash ROM
> Creating 3 MTD partitions on "Gumstix Flash ROM":
> 0x00000000-0x00040000 : "Bootloader"
> 0x00040000-0x01f00000 : "RootFS"
> 0x01f00000-0x02000000 : "Kernel"
> TCP cubic registered
> XScale iWMMXt coprocessor detected.
> VFS: Mounted root (jffs2 filesystem).
> Freeing init memory: 132K
> NET: Registered protocol family 1
> smc91x.c: v1.1, sep 22 2004 by Nicolas Pitre <ni...@ca...> <ni...@ca...>
> eth0: SMC91C11xFD (rev 2) at c8870300 IRQ 131 DMA 8 [nowait]
> eth0: Ethernet addr: 02:00:00:35:80:90
> eth0: PHY LAN83C183 (LAN91C111 Internal)
> CPLD responded with: 00
> usbcore: registered new interface driver usbfs
> usbcore: registered new interface driver hub
> usbcore: registered new device driver usb
> ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
> pxa27x-ohci pxa27x-ohci: PXA27x OHCI
> pxa27x-ohci pxa27x-ohci: new USB bus registered, assigned bus number 1
> pxa27x-ohci pxa27x-ohci: irq 3, io mem 0x4c000000
> usb usb1: configuration #1 chosen from 1 choice
> hub 1-0:1.0: USB hub found
> hub 1-0:1.0: 3 ports detected
> pccard: PCMCIA card inserted into slot 0
> pcmcia: registering new device pcmcia0.0
> Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
> ide: Assuming 50MHz system bus speed for PIO modes; override with idebus=xx
> Probing IDE interface ide0...
> usbcore: registered new interface driver usblp
> drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
> hda: CF2GHS, CFA DISK drive
> ide0 at 0xc8880000-0xc8880007,0xc888000e on irq 141
> ide-cs: hda: Vpp = 0.0
> SCSI subsystem initialized
> libata version 2.20 loaded.
> hda: max request size: 128KiB
> hda: 3915072 sectors (2004 MB) w/1KiB Cache, CHS=3884/16/63
>  hda: hda1
> eth0: link down
> cfio: module license 'unspecified' taints kernel.
> Before register driver
> After register driver
> NET: Registered protocol family 10
> ADDRCONF(NETDEV_UP): eth0: link is not ready
> Mobile IPv6
> eth0: link up, 100Mbps, full-duplex, lpa 0xC5E1
> ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
> eth0: no IPv6 routers present
>
>
>
> -------------------------------------------------------------------------
> Check out the new SourceForge.net Marketplace.
> It's the best place to buy or sell services for
> just about anything Open Source.
> http://sourceforge.net/services/buy/index.php
> _______________________________________________
> gumstix-users mailing list
> gum...@li...
> https://lists.sourceforge.net/lists/listinfo/gumstix-users
>
>