From: Steve S. <sa...@gm...> - 2006-09-22 20:57:06
|
Just did a sync & build of 1093 and my wifistix stopped working. Anyone else see this problem? Boot messages below: ### JFFS2 load complete: 755616 bytes loaded to 0xa2000000 ## Booting image at a2000000 ... Image Name: uImage Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 755552 Bytes = 737.8 kB Load Address: a0008000 Entry Point: a0008000 Verifying Checksum ... OK OK Starting kernel ... Linux version 2.6.18gum (steve@ubuntu) (gcc version 3.4.5) #1 Fri Sep 22 11:54:26 PDT 2006 CPU: XScale-PXA255 [69052d06] revision 6 (ARMv5TE), cr=0000397f Machine: The Gumstix Platform Memory policy: ECC disabled, Data cache writeback Memory clock: 99.53MHz (*27) Run Mode clock: 199.07MHz (*2) Turbo Mode clock: 199.07MHz (*1.0, inactive) CPU0: D VIVT undefined 5 cache CPU0: I cache: 32768 bytes, associativity 32, 32 byte lines, 32 sets CPU0: D cache: 32768 bytes, associativity 32, 32 byte lines, 32 sets Built 1 zonelists. Total pages: 16384 Kernel command line: console=ttyS0,115200n8 root=1f01 rootfstype=jffs2 PID hash table entries: 512 (order: 9, 2048 bytes) start_kernel(): bug: interrupts were enabled early Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) Memory: 64MB = 64MB total Memory: 63360KB available (1236K code, 249K data, 60K init) Mount-cache hash table entries: 512 CPU: Testing write buffer coherency: ok NET: Registered protocol family 16 NET: Registered protocol family 2 IP route cache hash table entries: 512 (order: -1, 2048 bytes) TCP established hash table entries: 2048 (order: 1, 8192 bytes) TCP bind hash table entries: 1024 (order: 0, 4096 bytes) TCP: Hash tables configured (established 2048 bind 1024) TCP reno registered JFFS2 version 2.2. (NAND) (C) 2001-2006 Red Hat, Inc. Initializing Cryptographic API io scheduler noop registered (default) pxa2xx-uart.0: ttyS0 at MMIO 0x40100000 (irq = 15) is a FFUART pxa2xx-uart.1: ttyS1 at MMIO 0x40200000 (irq = 14) is a BTUART pxa2xx-uart.2: ttyS2 at MMIO 0x40700000 (irq = 13) is a STUART pxa2xx-uart.3: ttyS3 at MMIO 0x41600000 (irq = 0) is a HWUART Probing Gumstix Flash ROM at physical address 0x00000000 (16-bit bankwidth) Gumstix Flash ROM: Found 1 x16 devices at 0x0 in 16-bit bank Intel/Sharp Extended Query Table at 0x0031 Using buffer write method cfi_cmdset_0001: Erase suspend on write enabled Using static partitions on Gumstix Flash ROM Creating 2 MTD partitions on "Gumstix Flash ROM": 0x00000000-0x00040000 : "Bootloader" 0x00040000-0x01000000 : "RootFS" TCP bic registered VFS: Mounted root (jffs2 filesystem). Freeing init memory: 60K NET: Registered protocol family 1 CPLD responded with: 00 Initializing random number generator... pccard: PCMCIA card inserted into slot 0pcmcia: registering new device pcmcia0.0 done. Starting 32kHz clock...Settled Set (AF1,out,clear) via /proc/gpio/GPIO12 Starting Bluetooth subsystem:Trying baud rate 57600... Set (GPIO,out,clear) via /proc/gpio/GPIO7 Set (GPIO,out,set) via /proc/gpio/GPIO7 No response after reset No response from BT module Trying baud rate 115200... Set (GPIO,out,clear) via /proc/gpio/GPIO7 Set (GPIO,out,set) via /proc/gpio/GPIO7 No response after reset No response from BT module Trying baud rate 921600... Set (GPIO,out,clear) via /proc/gpio/GPIO7 Set (GPIO,out,set) via /proc/gpio/GPIO7 No response after reset No response from BT module Can't initialize device: Success Starting network... udhcpc (v0.9.9-pre) started Dec 31 16:01:09 udhcpc[205]: udhcpc (v0.9.9-pre) started pxa2xx_udc: version 4-May-2005 ether gadget: using random self ethernet address ether gadget: using random host ethernet address usb0: Ethernet Gadget, version: May Day 2005 usb0: using pxa2xx_udc, OUT ep2out-bulk IN ep1in-bulk STATUS ep6in-bulk usb0: MAC 4a:03:55:f0:55:45 usb0: HOST MAC c6:8c:6a:e8:09:be usb0: RNDIS ready Nothing to flush. NET: Registered protocol family 17 udhcpc (v0.9.9-pre) started Dec 31 16:01:10 udhcpc[237]: udhcpc (v0.9.9-pre) started smc91x: not found (-19). m Dec 31 16:01:11 udhcpc[237]: [truncated] m Dec 31 16:01:11 modprobe: FATAL: Error running install command for cfio Error for wireless request "Set ESSID" (8B1A) : SET failed on device mwlan0 ; No such device. Starting Rendezvous: Starting dropbear sshd: OK Starting httpd... Welcome to the Gumstix Linux Distribution! gumstix login: |