[Emc-commit] TRUNK emc2/docs/src/common Glossary.lyx,1.8,1.9

[John T. <cv...@cv...>]

Modified file emc2/docs/src/common/Glossary.lyx

Full file:
<http://cvs.linuxcnc.org/cvs/emc2/docs/src/common/Glossary.lyx?rev=1.9>

Difference:
<http://cvs.linuxcnc.org/cvs/emc2/docs/src/common/Glossary.lyx.diff?r1=1.8;r2=1.9>

Branch: TRUNK

Log:
revision 1.9
date: 2008/08/30 14:38:25;  author: bigjohnt;  state: Exp;  lines: +31 -172
remove same page references

--- Glossary.lyx	2008/05/05 18:50:47	1.8
+++ Glossary.lyx	2008/08/30 14:38:25	1.9
@@ -35,7 +35,7 @@
  installers, and developers.
  
 \begin_inset Note
-collapsed true
+collapsed false
 
 \layout Standard
 
@@ -71,19 +71,9 @@
 
 \end_inset 
 
- A type of lead-screw 
-\begin_inset LatexCommand \ref{Leadscrew}
-
-\end_inset 
-
- that uses an acme thread form.
+ A type of lead-screw that uses an acme thread form.
  Acme threads have somewhat lower friction and wear than simple triangular
- threads, but ball-screws 
-\begin_inset LatexCommand \ref{Ballscrew}
-
-\end_inset 
-
- are lower yet.
+ threads, but ball-screws are lower yet.
  Most manual machine tools use acme lead-screws.
 \layout Description
 
@@ -129,12 +119,7 @@
 \end_inset 
 
  The amount of "play" or lost motion that occurs when direction is reversed
- in a lead screw 
-\begin_inset LatexCommand \ref{Leadscrew}
-
-\end_inset 
-
-.
+ in a lead screw.
  or other mechanical motion driving system.
  It can result from nuts that are loose on leadscrews, slippage in belts,
  cable slack, "wind-up" in rotary couplings, and other places where the
@@ -175,18 +160,9 @@
 \end_inset 
 
  A type of lead-screw that uses small hardened steel balls between the nut
- 
-\begin_inset LatexCommand \ref{Ballnut}
-
-\end_inset 
-
  and screw to reduce friction.
- Ball-screws have very low friction and backlash 
-\begin_inset LatexCommand \ref{Backlash}
-
-\end_inset 
-
-, but are usually quite expensive.
+ Ball-screws have very low friction and backlash, but are usually quite
+ expensive.
 \layout Description
 
 Ball\SpecialChar ~
@@ -218,12 +194,7 @@
  Computer Numerical Control.
  The general term used to refer to computer control of machinery.
  Instead of a human operator turning cranks to move a cutting tool, CNC
- uses a computer and motors to move the tool, based on a part program 
-\begin_inset LatexCommand \ref{PartProgram}
-
-\end_inset 
-
-.
+ uses a computer and motors to move the tool, based on a part program .
 \layout Description
 
 Comp
@@ -318,12 +289,7 @@
 \end_inset 
 
  The Enhanced Machine Controller.
- Initially a NIST 
-\begin_inset LatexCommand \ref{NIST}
-
-\end_inset 
-
- project.
+ Initially a NIST project.
  EMC is able to run a wide range of motion devices.
 \layout Description
 
@@ -337,13 +303,8 @@