Hi,
Only one option available for circle command
Please add following options
1)2Point - diameter.
2)3Point
3)PTR - Point, Tangent & Radius.
4)TTR - Tangent to 2 circles & Radius.
5)Arc - Select an arc for converting to circle.
Interesting this.
Could you detail how those options would work?
Meaning how the user should enter those infos? I will leave this as an important feature but as I keep saying: don't expect it to be ready so very soon. Development is quite still because I can't find much time and I have nobody to help me.
Hugo
If you would like to refer to this comment somewhere else in this project, copy and paste the following link:
Circle command should give following options at command Prompt
Command:C
2Point/3Point/PTR/TTR/Arc/<Center of circle>:
USING ABOVE OPTIONS
_ To draw a circle by specifying two points on the diameter
Command:C
2Point/3Point/PTR/TTR/Arc/<Center of circle>:2P
First point on diameter: (Specify the first point on the diameter of the circle.)
Second point on diameter: (Specify the second point on the diameter of the circle.)
_ To draw a circle by specifying its center and radius
Command:C
2Point/3Point/PTR/TTR/Arc/<Center of circle>:
_ To draw a circle tangent to existing entity & a specified point
Command:C
2Point/3Point/PTR/TTR/Arc/<Center of circle>:PTR
Select the first entity to which to draw the circle tangent:
Select the Point through which to draw the circle:
Specify the radius of the circle.
_ To draw a circle tangent to existing entities
Command:C
2Point/3Point/PTR/TTR/Arc/<Center of circle>:TTR
Select the first entity to which to draw the circle tangent:
Select the second entity to which to draw the circle tangent:
Specify the radius of the circle.
_ To convert an arc to a circle
Command:C
2Point/3Point/PTR/TTR/Arc/<Center of circle>:A
Select the arc you want to convert to a circle.
Hope this explains a little bit.
Regards
Sanjit
If you would like to refer to this comment somewhere else in this project, copy and paste the following link:
Thanks a lot. :)
Great description. I have to think a little bit about this but I think it's not too hard to implement and, therefore, quick. If it is, I will insert this in the next release (whenever I manage to do it).
Friendly,
Hugo
If you would like to refer to this comment somewhere else in this project, copy and paste the following link:
Logged In: YES
user_id=783053
Originator: NO
Interesting this.
Could you detail how those options would work?
Meaning how the user should enter those infos? I will leave this as an important feature but as I keep saying: don't expect it to be ready so very soon. Development is quite still because I can't find much time and I have nobody to help me.
Hugo
Logged In: YES
user_id=1847007
Originator: YES
Hi Hugo,
Circle command should give following options at command Prompt
Command:C
2Point/3Point/PTR/TTR/Arc/<Center of circle>:
USING ABOVE OPTIONS
_ To draw a circle by specifying two points on the diameter
Command:C
2Point/3Point/PTR/TTR/Arc/<Center of circle>:2P
First point on diameter: (Specify the first point on the diameter of the circle.)
Second point on diameter: (Specify the second point on the diameter of the circle.)
_ To draw a circle by specifying its center and radius
Command:C
2Point/3Point/PTR/TTR/Arc/<Center of circle>:
_ To draw a circle tangent to existing entity & a specified point
Command:C
2Point/3Point/PTR/TTR/Arc/<Center of circle>:PTR
Select the first entity to which to draw the circle tangent:
Select the Point through which to draw the circle:
Specify the radius of the circle.
_ To draw a circle tangent to existing entities
Command:C
2Point/3Point/PTR/TTR/Arc/<Center of circle>:TTR
Select the first entity to which to draw the circle tangent:
Select the second entity to which to draw the circle tangent:
Specify the radius of the circle.
_ To convert an arc to a circle
Command:C
2Point/3Point/PTR/TTR/Arc/<Center of circle>:A
Select the arc you want to convert to a circle.
Hope this explains a little bit.
Regards
Sanjit
Logged In: YES
user_id=783053
Originator: NO
Thanks a lot. :)
Great description. I have to think a little bit about this but I think it's not too hard to implement and, therefore, quick. If it is, I will insert this in the next release (whenever I manage to do it).
Friendly,
Hugo
Logged In: NO
TTR option very much used in AutoCAD mechanical drafting