RadAsm30 Files

Digital Scope
-------------
  o Input
    - AC / DC
    - 20mV to 2V / Div
    - 10MHz at -3db
    - Max 15MHz
  o Timebase
    - 10ns to 500ms / Div
    - Sliding wave on 250ms and 500ms
  o Trigger
    - Pre trigger
    - Rising edge
    - Falling edge
    - Trigger position
  o Position
    - Vertical
    - Horisontal
  o Single shot
  o Hold
  o Auto
  o Frequency and period

Logic Analyser
--------------
  o Channels: 4 bits
  o Trigger: High, Low or don't care
  o Sample size: 256, 512, 1K, 2K, 4K, 8K and 16K
  o Sample rate: 1Hz, 10Hz, 100Hz, 1KHz, 10KHz,
    100KHz, 1MHz, 10MHz and 20MHz
  o Search: Next / previous trigger

Wave Generator
--------------
  0 Off, Sine, triangle, squear, sawtooth and reverse sawtooth
    - Slow, 100Hz to 20KHz in 1, 2, 5 steps
    - Slow: Output changes every 1 second
    - 250mV, 500mV, 1V, 1.5V, 2v, 2.5V and 3V peak to peak
      output.

HS Clock
--------
  o Squear wave output
    - 3.3Vpp output
    - 1Hz to 40MHz frequency
    - Resolution: Any frequency that can be
      obtained by dividing 80MHz clock
    - Dutycycle: 10% to 90% in 10% steps

DDS Sqear Wave
--------------
  o Squear wave output
    - 3.3Vpp output
    - 1 Hz to 999999 Hz
    - Resolution: 1 Hz
    - Sweep 0% and 1% to 50% in 1, 2, 5 steps
    - Sweep time 1s to 10s  in 1, 2, 5 steps

Digital Multimeter
------------------
  o Voltmeter
    - +/- 19.99 Volt DC
  0 Ohm-meter
    - 50 Ohm - 500 KOhm
  o Continuity test
    - Blinking indicator
  o Diode test
  o Transistor test
    - Auto detect NPN / PNP

LC Meter
--------
  o Inductor
    - Autorange: nH, uH, mH and H
  o Capacitor
    - Autorange: pF. nf and uF
  o Calibration

Stopwatch
---------
  o 10ms resolution
    - Format hhh:mm:ss.nn
    
Timer
-----
  o Countdown timer
    - Format hh:mm:ss

Parts needed
------------
1 x STM32F401
1 x 4.0 inch SPI LCD with ST7796 controller
1 x TLE2072CP IC, 2 x OP Amp
1 x TL074CN IC, 4 x OP Amp
1 x TL712CP IC, 1 x Comparator
1 x LM311P IC, 1 x Comparator
4 x BC337 Transistor
5 x 1N4148 Diode
1 x 40pF trimmer capacitor
1 x B0505 1W Voltage converter
4 x SIP-1A05 5V reed relay
1 x 5V DPDT Relay
4 x Tactile switch
1 x 40 pin single row male header
2 x 40 pin single row female header
1 x 10cm x 16cm single sided pcb

Resistors 1/4W 1% metal film:
3 x 10Ohm
2 x 100Ohm
1 x 330Ohm
3 x 470Ohm
1 x 820Ohm
6 x 1K
3 x 4K7
5 x 10K
1 x 22K
3 x 47K
1 x 82K
5 x 100K
1 x 120K
1 x 180K
1 x 680K
3 x 1M

Ceramic capacitors:
1 x 68pF
2 x 220pF
4 x 100nF

Film capacitors:
2 x 1nF 1%
1 x 1uF

Electrolyte capacitors:
2 x 220uF 16V

Tantal capacitors:
4 x 10uF 10V
8 x 47uF 10V

Inductors:
1 x 82uH

KetilO