User Ratings

★★★★★
★★★★
★★★
★★
★
16
0
0
0
0
ease 1 of 5 2 of 5 3 of 5 4 of 5 5 of 5 4 / 5
features 1 of 5 2 of 5 3 of 5 4 of 5 5 of 5 4 / 5
design 1 of 5 2 of 5 3 of 5 4 of 5 5 of 5 4 / 5
support 1 of 5 2 of 5 3 of 5 4 of 5 5 of 5 5 / 5

Rate This Project
Login To Rate This Project

User Reviews

  • 5 out of 5 stars
    Very good ! And the author give help if required...
  • 5 out of 5 stars
    High level of development. Brilliant results, the only modest one is the author himself. Thank you, sir.
  • 5 out of 5 stars
    отлично. подскажите чем можно заменить ld1086v33.
  • 5 out of 5 stars
    Great project. Easy to build & easy to use.
  • 5 out of 5 stars
    Спасибо ! Отличный программатор!
  • 5 out of 5 stars
    I could build and use the Open Programmer in my first trial with programmers in my life. Without it I could still be searching. Thank you for the opportunity. I do appreciate this project.
  • 5 out of 5 stars
    This is a very well thought-out project and very well presented. This makes for a very enjoyable project to build, but also leaves you with a usefull/neccassary piece of kit for the future. Well done Alberto..and thank you. Jan
  • 5 out of 5 stars
    Llevaba tiempo buscando un programador con estas caracteristicas...y open source!!!! Solo falta implementar memorias paralelas.... Estoy haciendo la traduccion al español de la aplicacion, ya te la enviare. Un saludo y felicidades por el gran trabajo que has realizado.
  • 5 out of 5 stars
    Exactly what i need. Awesome project, keep it up!
  • 5 out of 5 stars
    Ihave an K150 and a PicKit3 (clone) programmer but this one is the best .It is made to be friendly with the user not with the "seller", I am new in this HOBBY but for begining I am 100% pleased. Stefan
  • 5 out of 5 stars
    This is an awesome project. Programmer is easy to build, easy to use and low-cost! I'm using it for three years and there was NO problems with it. Alberto - you are a genius!
  • 5 out of 5 stars
    This project was awesome!! first i try to build it on universal pcb board, i works then.. the internal Vreg was blew up, it warms then suddenly the Vusb pin died, cannot connect to usb. The usb communication failed. After do some research, i read the datasheet of 18F2550 and i can use external power to my vdd (Vusb is >= vdd) rail it says. So make story short i put 330uh, 1k resistor and disable the Vreg bit off on fuse and it works. Now i finally use my programmer!! tnx!! i wish for update is support atmega series like atmge2560 and so on!!
  • 5 out of 5 stars
    Awesome programmer i built it on a perfboard it works like a charm. It brought all my PICs and AVRs back to life :)
    1 user found this review helpful.
  • 5 out of 5 stars
    Look nice thanks. Keep it up!
  • 5 out of 5 stars
    Nice and Easy to use.
  • 5 out of 5 stars
    I am trying to learn how to program PIC's and have been looking for a programmer that I could build for a low cost, work reliably, support newer chips, and work with different brands of devices. This project meets and exceeds all my requirements. I was able to follow the instructions and on my first attempt succeeded in making a working programmer that is modular in design. I now have a much better programmer than the one I had been fighting with up to this point. A lot of thought and effort has been put into this project and I appreciate the high quality results very much!
  • Previous
  • You're on page 1
  • Next