Menu
▾
▴
Re: [xcat-user] PXE-E18: Server response timeout.
|
From: David J. <dav...@br...> - 2020-05-27 14:39:26
|
So from the logs, it seems that there were ?3? replies from three different DHCP servers? There should only be one. The makedhcp -d command should be run to delete the MAC->IP mapping on the XX.XX.X.XXX host, if that is the production server. It looks like you got rid of the MAC address from the JJ.JJ.J.JJJ server only. > On May 27, 2020, at 10:07 AM, John Roche <joh...@cr...> wrote: > > Hi ddj, > > Yes I’m pulling a few nodes from the prod cluster, > I did makedhcp -d nodename and this sort of helped > > It does a pxe boot, but still picks up the prod xcat server address > > xcatprobe detect_dhcpd -i <MN interface name> -m <node's mac address> > > Server: XX.XX.X.XXX assign IP [XX.XX.X.XXX]. The next server is [XX.XX.X.XXX]! [INFO] ß--- this is the prod xcat server, how do I remove this?? > Server: XX.XX.X.XXX assign IP [ZZ.ZZ.Z.ZZZ]. The next server is [ZZ.ZZ.Z.ZZZ]! [INFO] <- THIS IS THE NEW TEST XCAT SERVER > > Is there any way to remove this, will this help? > > JR > > > > > From: David D Johnson <dav...@br...> > Sent: 27 May 2020 12:23 > To: xCAT Users Mailing list <xca...@li...> > Subject: Re: [xcat-user] PXE-E18: Server response timeout. > > When you have two dhcp servers on the same wire/subnet, need to make sure that the MAC address > is only recognized by one of them. If the "production" server is running xcat, use makedhcp -d nodename > to get rid of the association over there, and presume (or check, with makedhcp -q nodename) that it's > registered in your new cluster. My guess is that you pulled out a compute node from the production cluster > to play with. > > -- ddj > > On May 27, 2020, at 5:08 AM, John Roche <joh...@cr... <mailto:joh...@cr...>> wrote: > > [A[root@xcat-test ~]# xcatprobe xcatmn -i eth0 > [mn]: Checking all xCAT daemons are running... [ OK ] > [mn]: Checking xcatd can receive command request... [ OK ] > [mn]: Checking 'site' table is configured... [ OK ] > [mn]: Checking provision network is configured... [ OK ] > [mn]: Checking 'passwd' table is configured... [ OK ] > [mn]: Checking important directories(installdir,tftpdir) are configured... [ OK ] > [mn]: Checking SELinux is disabled... [ OK ] > [mn]: Checking HTTP service is configured... [ OK ] > [mn]: Checking TFTP service is configured... [ OK ] > [mn]: Checking DNS service is configured... [ OK ] > [mn]: Checking DHCP service is configured... [ OK ] > [mn]: Checking NTP service is configured... [ OK ] > [mn]: Checking rsyslog service is configured... [ OK ] > [mn]: Checking firewall is disabled... [ OK ] > [mn]: Checking minimum disk space for xCAT ['/var' needs 1GB;'/install' needs 10GB;'/tmp' needs 1GB]... [ OK ] > [mn]: Checking Linux ulimits configuration... [ OK ] > [mn]: Checking network kernel parameter configuration... [ OK ] > [mn]: Checking xCAT daemon attributes configuration... [ OK ] > [mn]: Checking xCAT log is stored in /var/log/xcat/cluster.log... [ OK ] > [mn]: Checking xCAT management node IP: <10.28.9.183> is configured to static... [ OK ] > [mn]: Checking dhcpd.leases file is less than 100M... [ OK ] > =================================== SUMMARY ==================================== > [MN]: Checking on MN... [ OK ] > > That’s all good > > xcatprobe detect_dhcpd -i <MN interface name> -m <node's mac address> > > Start to detect DHCP, please wait 10 seconds [INFO] > ++++++++++++++++++++++++++++++++++ [INFO] > There are 3 servers replied to dhcp discover. [INFO] > Server: XX.XX.X.XXX assign IP [XX.XX.X.XXX]. The next server is [XX.XX.X.XXX]! [INFO] ß--- this is the prod xcat server, how do I remove this?? > Server: XX.XX.X.XXX assign IP [ZZ.ZZ.Z.ZZZ]. The next server is [ZZ.ZZ.Z.ZZZ]! [INFO] <- THIS IS THE NEW TEST XCAT SERVER > Server:JJ.JJ.JJ.J assign IP [JJ.JJ.J.J]. The next server is [ZZ.ZZ.Z.ZZZ]! [INFO] > ++++++++++++++++++++++++++++++++++ [INFO] > [root@xcat-test ~]# > > From: Casandra H Qiu <cx...@us... <mailto:cx...@us...>> > Sent: 26 May 2020 17:17 > To: xCAT Users Mailing list <xca...@li... <mailto:xca...@li...>> > Subject: Re: [xcat-user] PXE-E18: Server response timeout. > > try those two command to diagnosis if there are configure issues > > xcatprobe xcatmn -i <MN interface name> > xcatprobe detect_dhcpd -i <MN interface name> -m <node's mac address> > > > Thanks, > Casandra Qiu > > ................................................................... > Casandra Hong Qiu > Phone: (845) 433-9291, t/l 293-9291 > Office: Building 8, 3-B-04 > cx...@us... <mailto:cx...@us...> > > > > <image001.gif>John Roche ---05/26/2020 12:11:36 PM---Tried this No luck > > From: John Roche <joh...@cr... <mailto:joh...@cr...>> > To: xCAT Users Mailing list <xca...@li... <mailto:xca...@li...>> > Date: 05/26/2020 12:11 PM > Subject: Re: [xcat-user] [External] PXE-E18: Server response timeout. > > > > Tried this > No luck > > How did people set up the dhpc part for doing a pxe boot? > > John > > From: Jarrod Johnson <jjo...@le... <mailto:jjo...@le...>> > Sent: 22 May 2020 17:25 > To: xCA...@li... <mailto:xCA...@li...> > Subject: Re: [xcat-user] [External] PXE-E18: Server response timeout. > > Hmm, nodeset <nodename> stat > > Rinstall thould have taken care of that, but checking... > From: John Roche <joh...@cr... <mailto:joh...@cr...>> > Sent: Friday, May 22, 2020 8:40 AM > To: xCA...@li... <mailto:xCA...@li...> <xCA...@li... <mailto:xCA...@li...>> > Subject: [External] [xcat-user] PXE-E18: Server response timeout. > > Hi, > > I recently build an xcat server > Rpower works > But doing an rinstall, it keeps failing at the PXE boot > I’m doing rinstal <node name> -u > It uses UEFI > > I’m starting to pull my hair now on what’s the issue > Here is the error I see when I’m doing an rcons. > > Thanks > > > Boot Failed - PXE Network: PciRoot(0x0)/Pci(0x2,0x0)/Pci(0x0,0x0)/Ctrl(0x1)/MAC(E41D2DDE7931,0x0)/IPv4(0.0.0.0,0x0,DHCP,0.0.0.0,0.0.0.0,0.0.0.0) > > >>Start PXE over IPv4. > PXE-E18: Server response timeout. > > >>Start PXE over IPv4. > PXE-E18: Server response timeout. > Boot Failed - PXE Network: PciRoot(0x0)/Pci(0x2,0x0)/Pci(0x0,0x0)/Ctrl(0x2)/MAC(E41D2DDE7932,0x0)/IPv4(0.0.0.0,0x0,DHCP,0.0.0.0,0.0.0.0,0.0.0.0) > > >>Start PXE over IPv4. > The Francis Crick Institute Limited is a registered charity in England and Wales no. 1140062 and a company registered in England and Wales no. 06885462, with its registered office at 1 Midland Road London NW1 1AT > The Francis Crick Institute Limited is a registered charity in England and Wales no. 1140062 and a company registered in England and Wales no. 06885462, with its registered office at 1 Midland Road London NW1 1AT_______________________________________________ > xCAT-user mailing list > xCA...@li... <mailto:xCA...@li...> > https://lists.sourceforge.net/lists/listinfo/xcat-user <https://eur03.safelinks.protection.outlook.com/?url=https%3A%2F%2Flists.sourceforge.net%2Flists%2Flistinfo%2Fxcat-user&data=02%7C01%7C%7Cab0c8f1762cb4a430d0c08d80238fb08%7C4eed7807ebad415aa7a99170947f4eae%7C0%7C0%7C637261791048773760&sdata=CCAkXvkrEBoPQzuIyr1GycH48Kbt%2FbQnoQ7k%2Fxn6Evo%3D&reserved=0> > > > > > The Francis Crick Institute Limited is a registered charity in England and Wales no. 1140062 and a company registered in England and Wales no. 06885462, with its registered office at 1 Midland Road London NW1 1AT > _______________________________________________ > xCAT-user mailing list > xCA...@li... <mailto:xCA...@li...> > https://lists.sourceforge.net/lists/listinfo/xcat-user <https://eur03.safelinks.protection.outlook.com/?url=https%3A%2F%2Flists.sourceforge.net%2Flists%2Flistinfo%2Fxcat-user&data=02%7C01%7C%7Cab0c8f1762cb4a430d0c08d80238fb08%7C4eed7807ebad415aa7a99170947f4eae%7C0%7C0%7C637261791048783753&sdata=6JTm7OBdzCDiJQeCJtJ%2FW6%2FhLomLFZl%2FpuHczrA26zQ%3D&reserved=0> > > The Francis Crick Institute Limited is a registered charity in England and Wales no. 1140062 and a company registered in England and Wales no. 06885462, with its registered office at 1 Midland Road London NW1 1AT > > _______________________________________________ > xCAT-user mailing list > xCA...@li... <mailto:xCA...@li...> > https://lists.sourceforge.net/lists/listinfo/xcat-user <https://lists.sourceforge.net/lists/listinfo/xcat-user> |
