|
From: Ion-Mihai T. <it...@ap...> - 2005-01-03 11:40:42
|
Hi, Could someone please tell me what the errors bellow mean ? Is there anyway to understand SMART logged errors without learning the hole standard (a link to some doc, something)? Thanks. # smartctl -a /dev/ad3 smartctl version 5.32 Copyright (C) 2002-4 Bruce Allen Home page is http://smartmontools.sourceforge.net/ === START OF INFORMATION SECTION === Device Model: ST340016A Serial Number: 3HS20XPG Firmware Version: 3.10 Device is: In smartctl database [for details use: -P show] ATA Version is: 5 ATA Standard is: Exact ATA specification draft version not indicated Local Time is: Mon Jan 3 13:32:18 2005 EET SMART support is: Available - device has SMART capability. SMART support is: Enabled The SMART RETURN STATUS return value (smartmontools -H option/Directive) can not be retrieved with this version of ATAng, please do not rely on this value === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 422) seconds. Offline data collection capabilities: (0x1b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. No Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. No General Purpose Logging support. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 31) minutes. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000f 080 063 034 Pre-fail Always - 141861872 3 Spin_Up_Time 0x0003 070 070 000 Pre-fail Always - 0 4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 833 5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always - 0 7 Seek_Error_Rate 0x000f 082 060 030 Pre-fail Always - 200897522 9 Power_On_Hours 0x0032 093 093 000 Old_age Always - 6404 10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0 12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 849 194 Temperature_Celsius 0x0022 030 058 000 Old_age Always - 30 195 Hardware_ECC_Recovered 0x001a 080 063 000 Old_age Always - 141861872 197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x003e 200 091 000 Old_age Always - 197 200 Multi_Zone_Error_Rate 0x0000 100 253 000 Old_age Offline - 0 202 TA_Increase_Count 0x0032 100 253 000 Old_age Always - 0 SMART Error Log Version: 1 ATA Error Count: 261 (device log contains only the most recent five errors) CR = Command Register [HEX] FR = Features Register [HEX] SC = Sector Count Register [HEX] SN = Sector Number Register [HEX] CL = Cylinder Low Register [HEX] CH = Cylinder High Register [HEX] DH = Device/Head Register [HEX] DC = Device Command Register [HEX] ER = Error register [HEX] ST = Status register [HEX] Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 261 occurred at disk power-on lifetime: 5829 hours (242 days + 21 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 d5 6f c7 f1 Error: UNC at LBA = 0x01c76fd5 = 29847509 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 20 00 01 d5 6f c7 f1 00 00:47:15.165 READ SECTOR(S) 91 00 3f 01 00 00 fe 02 00:47:15.064 INITIALIZE DEVICE PARAMETERS [OBS-6] 10 00 01 01 00 00 b0 00 00:47:15.064 RECALIBRATE [OBS-4] 00 00 00 00 00 00 00 06 00:47:14.964 NOP [Abort queued commands] c8 00 01 d5 6f c7 f1 00 00:47:11.064 READ DMA Error 260 occurred at disk power-on lifetime: 5829 hours (242 days + 21 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 d5 6f c7 f1 Error: UNC at LBA = 0x01c76fd5 = 29847509 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c8 00 01 d5 6f c7 f1 00 00:47:11.064 READ DMA ca 00 03 e7 53 c0 f1 00 00:47:11.049 WRITE DMA c8 00 08 df 7a c0 f1 00 00:47:11.002 READ DMA c8 00 1c c3 ca c4 f1 00 00:47:10.975 READ DMA c8 00 7e 45 ca c4 f1 00 00:47:10.969 READ DMA Error 259 occurred at disk power-on lifetime: 5829 hours (242 days + 21 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 1d f3 c3 f1 Error: UNC at LBA = 0x01c3f31d = 29618973 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 20 00 01 1d f3 c3 f1 00 00:46:47.209 READ SECTOR(S) 91 00 3f 01 00 00 fe 02 00:46:47.108 INITIALIZE DEVICE PARAMETERS [OBS-6] 10 00 01 01 00 00 b0 00 00:46:47.108 RECALIBRATE [OBS-4] 00 00 00 00 00 00 00 06 00:46:47.006 NOP [Abort queued commands] c8 00 01 1d f3 c3 f1 00 00:46:43.098 READ DMA Error 258 occurred at disk power-on lifetime: 5829 hours (242 days + 21 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 1d f3 c3 f1 Error: UNC at LBA = 0x01c3f31d = 29618973 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c8 00 01 1d f3 c3 f1 00 00:46:43.098 READ DMA 91 00 3f f1 d4 40 fe 02 00:46:42.997 INITIALIZE DEVICE PARAMETERS [OBS-6] 10 00 01 f1 d4 40 b0 00 00:46:42.997 RECALIBRATE [OBS-4] 91 00 3f 01 00 00 fe 02 00:46:09.692 INITIALIZE DEVICE PARAMETERS [OBS-6] 00 00 00 00 00 00 00 06 00:46:09.593 NOP [Abort queued commands] Error 257 occurred at disk power-on lifetime: 5829 hours (242 days + 21 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 1d f3 c3 f1 Error: UNC at LBA = 0x01c3f31d = 29618973 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 20 00 01 1d f3 c3 f1 00 00:46:05.642 READ SECTOR(S) 91 00 3f 01 00 00 fe 02 00:46:05.541 INITIALIZE DEVICE PARAMETERS [OBS-6] 10 00 01 01 00 00 b0 00 00:46:05.540 RECALIBRATE [OBS-4] 00 00 00 00 00 00 00 06 00:46:05.446 NOP [Abort queued commands] c8 00 01 1d f3 c3 f1 00 00:46:01.578 READ DMA SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Completed without error 00% 6391 - # 2 Short offline Completed without error 00% 6391 - # 3 Extended offline Completed without error 00% 5903 - # 4 Short offline Completed without error 00% 5902 - Device does not support Selective Self Tests/Logging -- IOnut Unregistered ;) FreeBSD "user" |