Menu
▾
▴
[Smartmontools-database] Request for addition to the database: SK hynix SH920 mSATA 256GB
|
From: Vadim L. <vad...@ma...> - 2016-03-02 09:02:14
|
smartctl 6.2 2013-07-26 r3841 [x86_64-linux-3.19.0-32-generic] (local build) Copyright (C) 2002-13, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Device Model: SK hynix SH920 mSATA 256GB Serial Number: EIE7M002212307Q5L Firmware Version: 1010BL00 User Capacity: 256Â 060Â 514Â 304 bytes [256 GB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device Device is: Not in smartctl database [for details use: -P showall] ATA Version is: ATA8-ACS (minor revision not indicated) SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Wed Mar 2 10:35:23 2016 EET SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 254 (maximum performance) Rd look-ahead is: Enabled Write cache is: Enabled ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Unavailable === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x02) Offline data collection activity was completed without error. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 5) seconds. Offline data collection capabilities: (0x19) SMART execute Offline immediate. No Auto Offline data collection support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. No Selective Self-test supported. SMART capabilities: (0x0002) Does not save SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 17) minutes. SMART Attributes Data Structure revision number: 0 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 166 166 006 - 0 5 Reallocated_Sector_Ct -O--CK 253 253 036 - 0 9 Power_On_Hours -O--CK 098 098 000 - 2344 12 Power_Cycle_Count -O--CK 100 100 020 - 1272 100 Unknown_Attribute -O--CK 100 100 000 - 1911783 171 Unknown_Attribute -O--CK 253 253 000 - 0 172 Unknown_Attribute -O--CK 253 100 000 - 0 174 Unknown_Attribute ----CK 100 100 000 - 92 175 Program_Fail_Count_Chip -O--CK 253 253 000 - 0 176 Erase_Fail_Count_Chip -O--CK 253 253 000 - 0 177 Wear_Leveling_Count -O--CK 100 100 000 - 1446016 178 Used_Rsvd_Blk_Cnt_Chip -O--CK 100 100 000 - 18 179 Used_Rsvd_Blk_Cnt_Tot -O--CK 100 100 000 - 70 180 Unused_Rsvd_Blk_Cnt_Tot -O--CK 100 100 000 - 5242 181 Program_Fail_Cnt_Total -O--CK 253 253 000 - 0 182 Erase_Fail_Count_Total -O--CK 253 100 000 - 0 183 Runtime_Bad_Block -O--CK 253 253 000 - 0 187 Reported_Uncorrect -O--CK 253 253 000 - 0 188 Command_Timeout -O--CK 253 253 000 - 0 191 Unknown_SSD_Attribute -O--CK 253 253 000 - 0 194 Temperature_Celsius -O---- 039 000 000 - 39 (Min/Max 18/59) 195 Hardware_ECC_Recovered -O--CK 253 253 000 - 0 201 Unknown_SSD_Attribute -OSR-- 100 100 000 - 0 204 Soft_ECC_Correction -OSR-- 100 100 --- - 0 231 Temperature_Celsius PO--CK 253 253 --- - 0 234 Unknown_Attribute -O--CK 100 100 --- - 5750 241 Total_LBAs_Written -O--CK 100 100 --- - 4021 242 Total_LBAs_Read -O--CK 100 100 --- - 1643 250 Read_Error_Retry_Rate -O--CK 100 100 --- - 8337 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 4 Comprehensive SMART error log 0x03 GPL R/O 5 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 2 Extended self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters 0x80-0x9f GPL,SL R/W 16 Host vendor specific log SMART Extended Comprehensive Error Log Version: 1 (5 sectors) Device Error Count: 7949 (device log contains only the most recent 20 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 7949 [8] occurred at disk power-on lifetime: 2342 hours (97 days + 14 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 00 -- 00 00 00 00 00 00 00 00 00 00 ff Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- Error 7948 [7] occurred at disk power-on lifetime: 2342 hours (97 days + 14 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 00 -- 00 00 00 00 00 00 00 00 00 00 ff Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- Error 7947 [6] occurred at disk power-on lifetime: 2342 hours (97 days + 14 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 00 -- 00 00 00 00 00 00 00 00 00 00 ff Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- Error 7946 [5] occurred at disk power-on lifetime: 2342 hours (97 days + 14 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 00 -- 00 00 00 00 00 00 00 00 00 00 ff Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- Error 7945 [4] occurred at disk power-on lifetime: 2334 hours (97 days + 6 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 00 -- 00 00 00 00 00 00 00 00 00 00 ff at LBA = 0x00000000 = 0 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 04 00 00 00 d0 32 fc 40 40 00:00:20.600 READ DMA EXT 25 00 00 00 3c 00 00 00 d0 32 c0 40 40 00:00:20.600 READ DMA EXT 25 00 00 00 03 00 00 00 d0 32 bd 40 40 00:00:20.600 READ DMA EXT 25 00 00 00 3d 00 00 00 d0 32 80 40 40 00:00:20.600 READ DMA EXT 25 00 00 00 02 00 00 00 d0 32 7e 40 40 00:00:20.600 READ DMA EXT Error 7944 [3] occurred at disk power-on lifetime: 2334 hours (97 days + 6 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 00 -- 00 00 00 00 00 00 00 00 00 00 ff at LBA = 0x00000000 = 0 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 04 00 00 00 d0 32 fc 40 40 00:00:20.600 READ DMA EXT 25 00 00 00 3c 00 00 00 d0 32 c0 40 40 00:00:20.600 READ DMA EXT 25 00 00 00 03 00 00 00 d0 32 bd 40 40 00:00:20.600 READ DMA EXT 25 00 00 00 3d 00 00 00 d0 32 80 40 40 00:00:20.600 READ DMA EXT 25 00 00 00 02 00 00 00 d0 32 7e 40 40 00:00:20.600 READ DMA EXT Error 7943 [2] occurred at disk power-on lifetime: 2334 hours (97 days + 6 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 00 -- 00 00 00 00 00 00 00 00 00 00 ff Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- ec 00 00 00 00 00 00 00 00 00 00 00 00 00:00:14.120 IDENTIFY DEVICE ec 00 00 00 00 00 00 00 00 00 00 00 00 00:00:13.050 IDENTIFY DEVICE ec 00 00 00 00 00 00 00 00 00 00 00 00 00:00:11.970 IDENTIFY DEVICE ec 00 00 00 00 00 00 00 00 00 00 00 00 00:00:10.900 IDENTIFY DEVICE ec 00 00 00 00 00 00 00 00 00 00 00 00 00:00:09.830 IDENTIFY DEVICE Error 7942 [1] occurred at disk power-on lifetime: 2334 hours (97 days + 6 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 00 -- 00 00 00 00 00 00 00 00 00 00 ff Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- ec 00 00 00 00 00 00 00 00 00 00 00 00 00:00:05.120 IDENTIFY DEVICE ec 00 00 00 00 00 00 00 00 00 00 00 00 00:00:05.120 IDENTIFY DEVICE ec 00 00 00 00 00 00 00 00 00 00 00 00 00:00:05.020 IDENTIFY DEVICE ec 00 00 00 00 00 00 00 00 00 00 00 00 00:00:04.930 IDENTIFY DEVICE ec 00 00 00 00 00 00 00 00 00 00 00 00 00:00:04.930 IDENTIFY DEVICE SMART Extended Self-test Log Version: 1 (2 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 2344 - # 2 Short offline Completed without error 00% 0 - Selective Self-tests/Logging not supported SCT Commands not supported Device Statistics (GP Log 0x04) Page Offset Size Value Description 1 ===== = = == General Statistics (empty) == 4 ===== = = == General Errors Statistics (empty) == 5 ===== = = == Temperature Statistics (empty) == 6 ===== = = == Transport Statistics (empty) == 7 ===== = = == Solid State Device Statistics (empty) == SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x000a 2 3 Device-to-host register FISes sent due to a COMRESET |