Menu
▾
▴
[Smartmontools-database] Some low-end flash drives: unknown, Kingmax, Toshiba
|
From: Ville O. <vo...@gm...> - 2013-12-12 06:45:51
|
Hi there, I have a bunch of low-end SSDs that are not recognized by smartmontools-database in TRUNK or the latest database that actually works with this version of smartmontools (3864). Below is -t short and -x for the following three drives: - Unknown 2 GB SATA-attached "industrial" flash drive, did not support self-test - KINGMAX SSD 240GB - TOSHIBA THNSNH I have access to two of each but will post only one of each type. Please copy me in any further correspondence as I am not subscribed to the list. Hope this information could be useful for someone. ----- Unknown 2 GB SATA-attached "industrial" flash drive: # smartctl -t short /dev/ada0 smartctl 5.43 2012-06-30 r3573 [XXX] (local build) Copyright (C) 2002-12 by Bruce Allen, http://smartmontools.sourceforge.net === START OF OFFLINE IMMEDIATE AND SELF-TEST SECTION === Warning: device does not support Self-Test functions. Sending command: "Execute SMART Short self-test routine immediately in off-line mode". (pass9:ahcich0:0:0:0): SMART. ACB: b0 d4 01 4f c2 40 00 00 00 00 00 00 (pass9:ahcich0:0:0:0): CAM status: ATA Status Error (pass9:ahcich0:0:0:0): ATA status: 51 (DRDY SERV ERR), error: 04 (ABRT ) (pass9:ahcich0:0:0:0): RES: 51 04 01 4f c2 40 00 00 00 00 00 Command "Execute SMART Short self-test routine immediately in off-line mode" failed: No error: 0 # smartctl -x /dev/ada0 smartctl 5.43 2012-06-30 r3573 [XXX] (local build) Copyright (C) 2002-12 by Bruce Allen, http://smartmontools.sourceforge.net === START OF INFORMATION SECTION === Device Model: 2GB SATA Flash Drive Serial Number: C01102121655X1350057 Firmware Version: SFDB103C User Capacity: 2,002,452,480 bytes [2.00 GB] Sector Size: 512 bytes logical/physical Device is: Not in smartctl database [for details use: -P showall] ATA Version is: 7 ATA Standard is: Exact ATA specification draft version not indicated Local Time is: Thu Dec 12 13:29:52 2013 ICT SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled ATA Security is: Disabled, NOT FROZEN [SEC1] === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Total time to complete Offline data collection: ( 0) seconds. Offline data collection capabilities: (0x00) Offline data collection not supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x00) Error logging NOT supported. No General Purpose Logging support. SMART Attributes Data Structure revision number: 1280 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 12 Power_Cycle_Count -O--CK 100 100 000 - 280 9 Power_On_Hours -O--CK 100 100 000 - 0 194 Temperature_Celsius POS--- 032 100 000 - 0 229 Unknown_Attribute -O---- 100 000 000 - 259934211134956 232 Available_Reservd_Space -O---- 100 048 000 - 1336560136249 233 Media_Wearout_Indicator -O---- 100 000 000 - 0 234 Unknown_Attribute -O---- 100 000 000 - 528314539778 235 Unknown_Attribute -O---- 100 000 000 - 3624005663 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning (pass9:ahcich0:0:0:0): SMART. ACB: b0 d5 00 4f c2 40 00 00 00 00 01 00 (pass9:ahcich0:0:0:0): CAM status: ATA Status Error (pass9:ahcich0:0:0:0): ATA status: 51 (DRDY SERV ERR), error: 04 (ABRT ) (pass9:ahcich0:0:0:0): RES: 51 04 00 4f c2 40 00 00 00 01 00 Read SMART Log Directory failed. (pass9:ahcich0:0:0:0): READ_LOG_EXT. ACB: 2f 00 00 00 00 40 00 00 00 00 01 00 (pass9:ahcich0:0:0:0): CAM status: ATA Status Error (pass9:ahcich0:0:0:0): ATA status: 51 (DRDY SERV ERR), error: 04 (ABRT ) (pass9:ahcich0:0:0:0): RES: 51 04 00 00 00 40 00 00 00 01 00 ATA_READ_LOG_EXT (addr=0x00:0x00, page=0, n=1) failed: No error: 0 Read GP Log Directory failed. SMART Extended Comprehensive Error Log (GP Log 0x03) not supported SMART Error Log not supported SMART Extended Self-test Log (GP Log 0x07) not supported SMART Self-test Log not supported Device does not support Selective Self Tests/Logging Warning: device does not support SCT Commands SATA Phy Event Counters (GP Log 0x11) not supported ----- KINGMAX SSD 240GB: # smartctl -t short /dev/ada1 smartctl 5.43 2012-06-30 r3573 [XXX] (local build) Copyright (C) 2002-12 by Bruce Allen, http://smartmontools.sourceforge.net === START OF OFFLINE IMMEDIATE AND SELF-TEST SECTION === Sending command: "Execute SMART Short self-test routine immediately in off-line mode". Drive command "Execute SMART Short self-test routine immediately in off-line mode" successful. Testing has begun. Please wait 1 minutes for test to complete. Test will complete after Thu Dec 12 13:32:07 2013 Use smartctl -X to abort test. # smartctl -x /dev/ada1 smartctl 5.43 2012-06-30 r3573 [XXX] (local build) Copyright (C) 2002-12 by Bruce Allen, http://smartmontools.sourceforge.net === START OF INFORMATION SECTION === Device Model: KINGMAX SSD 240GB Serial Number: 20130311080440123656 LU WWN Device Id: 0 0232d0 000000000 Firmware Version: M0116 User Capacity: 240,057,409,536 bytes [240 GB] Sector Size: 512 bytes logical/physical Device is: Not in smartctl database [for details use: -P showall] ATA Version is: 8 ATA Standard is: ACS-2 revision 3 Local Time is: Thu Dec 12 13:33:39 2013 ICT SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Disabled Rd look-ahead is: Enabled Write cache is: Enabled ATA Security is: Disabled, NOT FROZEN [SEC1] === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x02) Offline data collection activity was completed without error. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 0) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 48) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x0021) SCT Status supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 104 104 050 - 8557067 5 Reallocated_Sector_Ct PO--CK 100 100 003 - 0 9 Power_On_Hours -O--CK 095 095 000 - 4870 (153 234 0) 12 Power_Cycle_Count -O--CK 100 100 000 - 10 171 Unknown_Attribute -O--CK 000 000 000 - 0 172 Unknown_Attribute -O--CK 000 000 000 - 0 174 Unknown_Attribute ----CK 000 000 000 - 8 177 Wear_Leveling_Count ------ 000 000 000 - 1 181 Program_Fail_Cnt_Total -O--CK 000 000 000 - 0 182 Erase_Fail_Count_Total -O--CK 000 000 000 - 0 187 Reported_Uncorrect -O--CK 100 100 000 - 0 194 Temperature_Celsius -O---K 027 035 000 - 27 (Min/Max 15/35) 195 Hardware_ECC_Recovered --SRC- 120 120 000 - 8557067 196 Reallocated_Event_Count PO--CK 100 100 003 - 0 201 Soft_Read_Error_Rate --SRC- 120 120 000 - 8557067 204 Soft_ECC_Correction --SRC- 120 120 000 - 8557067 230 Head_Amplitude PO--C- 100 100 000 - 100 231 Temperature_Celsius PO--C- 100 100 010 - 0 233 Media_Wearout_Indicator ------ 000 000 000 - 6142 234 Unknown_Attribute -O--CK 000 000 000 - 7945 241 Total_LBAs_Written -O--CK 000 000 000 - 7945 242 Total_LBAs_Read -O--CK 000 000 000 - 453 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] GP/S Log at address 0x00 has 1 sectors [Log Directory] GP/S Log at address 0x04 has 1 sectors [Device Statistics log] GP Log at address 0x07 has 1 sectors [Extended self-test log] SMART Log at address 0x09 has 1 sectors [Selective self-test log] GP Log at address 0x10 has 1 sectors [NCQ Command Error log] GP/S Log at address 0x11 has 1 sectors [SATA Phy Event Counters] GP/S Log at address 0x80 has 16 sectors [Host vendor specific log] GP/S Log at address 0x81 has 16 sectors [Host vendor specific log] GP/S Log at address 0x82 has 16 sectors [Host vendor specific log] GP/S Log at address 0x83 has 16 sectors [Host vendor specific log] GP/S Log at address 0x84 has 16 sectors [Host vendor specific log] GP/S Log at address 0x85 has 16 sectors [Host vendor specific log] GP/S Log at address 0x86 has 16 sectors [Host vendor specific log] GP/S Log at address 0x87 has 16 sectors [Host vendor specific log] GP/S Log at address 0x88 has 16 sectors [Host vendor specific log] GP/S Log at address 0x89 has 16 sectors [Host vendor specific log] GP/S Log at address 0x8a has 16 sectors [Host vendor specific log] GP/S Log at address 0x8b has 16 sectors [Host vendor specific log] GP/S Log at address 0x8c has 16 sectors [Host vendor specific log] GP/S Log at address 0x8d has 16 sectors [Host vendor specific log] GP/S Log at address 0x8e has 16 sectors [Host vendor specific log] GP/S Log at address 0x8f has 16 sectors [Host vendor specific log] GP/S Log at address 0x90 has 16 sectors [Host vendor specific log] GP/S Log at address 0x91 has 16 sectors [Host vendor specific log] GP/S Log at address 0x92 has 16 sectors [Host vendor specific log] GP/S Log at address 0x93 has 16 sectors [Host vendor specific log] GP/S Log at address 0x94 has 16 sectors [Host vendor specific log] GP/S Log at address 0x95 has 16 sectors [Host vendor specific log] GP/S Log at address 0x96 has 16 sectors [Host vendor specific log] GP/S Log at address 0x97 has 16 sectors [Host vendor specific log] GP/S Log at address 0x98 has 16 sectors [Host vendor specific log] GP/S Log at address 0x99 has 16 sectors [Host vendor specific log] GP/S Log at address 0x9a has 16 sectors [Host vendor specific log] GP/S Log at address 0x9b has 16 sectors [Host vendor specific log] GP/S Log at address 0x9c has 16 sectors [Host vendor specific log] GP/S Log at address 0x9d has 16 sectors [Host vendor specific log] GP/S Log at address 0x9e has 16 sectors [Host vendor specific log] GP/S Log at address 0x9f has 16 sectors [Host vendor specific log] GP/S Log at address 0xb7 has 16 sectors [Device vendor specific log] GP/S Log at address 0xe0 has 1 sectors [SCT Command/Status] GP/S Log at address 0xe1 has 1 sectors [SCT Data Transfer] SMART Extended Comprehensive Error Log (GP Log 0x03) not supported SMART Error Log not supported SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 0 (0x0000) SCT Support Level: 1 Device State: Active (0) Current Temperature: 27 Celsius Power Cycle Min/Max Temperature: 24/30 Celsius Lifetime Min/Max Temperature: 15/33 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 10 minutes Min/Max recommended Temperature: ?/ ? Celsius Min/Max Temperature Limit: ?/ ? Celsius Temperature History Size (Index): 478 (181) Index Estimated Time Temperature Celsius 182 2013-12-09 06:00 27 ******** ... ..( 10 skipped). .. ******** [snip] 181 2013-12-12 13:30 26 ******* Warning: device does not support SCT Error Recovery Control command SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 12 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 10 Device-to-host register FISes sent due to a COMRESET 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0010 2 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 2 0 R_ERR response for host-to-device non-data FIS, non-CRC 0x0002 2 0 R_ERR response for data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS ----- TOSHIBA THNSNH: # smartctl -t short /dev/ada1 smartctl 5.43 2012-06-30 r3573 [XXX] (local build) Copyright (C) 2002-12 by Bruce Allen, http://smartmontools.sourceforge.net === START OF OFFLINE IMMEDIATE AND SELF-TEST SECTION === Sending command: "Execute SMART Short self-test routine immediately in off-line mode". Drive command "Execute SMART Short self-test routine immediately in off-line mode" successful. Testing has begun. Please wait 2 minutes for test to complete. Test will complete after Thu Dec 12 13:40:23 2013 Use smartctl -X to abort test. # smartctl -x /dev/ada1 smartctl 5.43 2012-06-30 r3573 [XXX] (local build) Copyright (C) 2002-12 by Bruce Allen, http://smartmontools.sourceforge.net === START OF INFORMATION SECTION === Device Model: TOSHIBA THNSNH256GCST Serial Number: 43AS108UTPHY LU WWN Device Id: 5 00080d b00040ce8 Firmware Version: HTRAN101 User Capacity: 256,060,514,304 bytes [256 GB] Sector Size: 512 bytes logical/physical Device is: Not in smartctl database [for details use: -P showall] ATA Version is: 8 ATA Standard is: ACS-2 (revision not indicated) Local Time is: Thu Dec 12 13:40:25 2013 ICT SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Disabled Rd look-ahead is: Enabled Write cache is: Enabled ATA Security is: Disabled, NOT FROZEN [SEC1] === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 120) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 14) minutes. SCT capabilities: (0x0039) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate -O-R-- 100 100 000 - 0 2 Throughput_Performance P-S--- 100 100 050 - 0 3 Spin_Up_Time POS--- 100 100 050 - 0 5 Reallocated_Sector_Ct PO--C- 100 100 050 - 0 7 Seek_Error_Rate PO-R-- 100 100 050 - 0 8 Seek_Time_Performance P-S--- 100 100 050 - 0 9 Power_On_Hours -O--C- 100 100 000 - 4419 10 Spin_Retry_Count PO--C- 100 100 050 - 0 12 Power_Cycle_Count -O--C- 100 100 000 - 11 167 Unknown_Attribute -O---K 100 100 000 - 0 168 Unknown_Attribute -O--C- 100 100 000 - 0 169 Unknown_Attribute PO--C- 100 100 010 - 100 173 Unknown_Attribute -O--C- 132 132 000 - 0 175 Program_Fail_Count_Chip PO--C- 100 100 010 - 0 192 Power-Off_Retract_Count -O--C- 100 100 000 - 6 194 Temperature_Celsius PO---K 072 064 020 - 28 (Min/Max 22/36) 197 Current_Pending_Sector -O--C- 100 100 000 - 0 240 Head_Flying_Hours PO--C- 100 100 050 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] GP/S Log at address 0x00 has 1 sectors [Log Directory] SMART Log at address 0x01 has 1 sectors [Summary SMART error log] SMART Log at address 0x02 has 51 sectors [Comprehensive SMART error log] GP Log at address 0x03 has 64 sectors [Ext. Comprehensive SMART error log] GP/S Log at address 0x04 has 8 sectors [Device Statistics log] SMART Log at address 0x06 has 1 sectors [SMART self-test log] GP Log at address 0x07 has 1 sectors [Extended self-test log] SMART Log at address 0x09 has 1 sectors [Selective self-test log] GP Log at address 0x10 has 1 sectors [NCQ Command Error log] GP Log at address 0x11 has 1 sectors [SATA Phy Event Counters] GP/S Log at address 0x30 has 9 sectors [IDENTIFY DEVICE data log] GP/S Log at address 0x80 has 16 sectors [Host vendor specific log] GP/S Log at address 0x81 has 16 sectors [Host vendor specific log] GP/S Log at address 0x82 has 16 sectors [Host vendor specific log] GP/S Log at address 0x83 has 16 sectors [Host vendor specific log] GP/S Log at address 0x84 has 16 sectors [Host vendor specific log] GP/S Log at address 0x85 has 16 sectors [Host vendor specific log] GP/S Log at address 0x86 has 16 sectors [Host vendor specific log] GP/S Log at address 0x87 has 16 sectors [Host vendor specific log] GP/S Log at address 0x88 has 16 sectors [Host vendor specific log] GP/S Log at address 0x89 has 16 sectors [Host vendor specific log] GP/S Log at address 0x8a has 16 sectors [Host vendor specific log] GP/S Log at address 0x8b has 16 sectors [Host vendor specific log] GP/S Log at address 0x8c has 16 sectors [Host vendor specific log] GP/S Log at address 0x8d has 16 sectors [Host vendor specific log] GP/S Log at address 0x8e has 16 sectors [Host vendor specific log] GP/S Log at address 0x8f has 16 sectors [Host vendor specific log] GP/S Log at address 0x90 has 16 sectors [Host vendor specific log] GP/S Log at address 0x91 has 16 sectors [Host vendor specific log] GP/S Log at address 0x92 has 16 sectors [Host vendor specific log] GP/S Log at address 0x93 has 16 sectors [Host vendor specific log] GP/S Log at address 0x94 has 16 sectors [Host vendor specific log] GP/S Log at address 0x95 has 16 sectors [Host vendor specific log] GP/S Log at address 0x96 has 16 sectors [Host vendor specific log] GP/S Log at address 0x97 has 16 sectors [Host vendor specific log] GP/S Log at address 0x98 has 16 sectors [Host vendor specific log] GP/S Log at address 0x99 has 16 sectors [Host vendor specific log] GP/S Log at address 0x9a has 16 sectors [Host vendor specific log] GP/S Log at address 0x9b has 16 sectors [Host vendor specific log] GP/S Log at address 0x9c has 16 sectors [Host vendor specific log] GP/S Log at address 0x9d has 16 sectors [Host vendor specific log] GP/S Log at address 0x9e has 16 sectors [Host vendor specific log] GP/S Log at address 0x9f has 16 sectors [Host vendor specific log] GP/S Log at address 0xe0 has 1 sectors [SCT Command/Status] GP/S Log at address 0xe1 has 1 sectors [SCT Data Transfer] SMART Extended Comprehensive Error Log Version: 1 (64 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 4419 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 3 (0x0003) SCT Support Level: 0 Device State: Active (0) Current Temperature: 28 Celsius Power Cycle Min/Max Temperature: 24/30 Celsius Lifetime Min/Max Temperature: 22/36 Celsius Lifetime Average Temperature: 22 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 5/40 Celsius Min/Max Temperature Limit: 0/80 Celsius Temperature History Size (Index): 128 (89) Index Estimated Time Temperature Celsius 90 2013-12-12 11:33 26 ******* ... ..( 49 skipped). .. ******* 12 2013-12-12 12:23 26 ******* 13 2013-12-12 12:24 27 ******** 14 2013-12-12 12:25 26 ******* ... ..( 63 skipped). .. ******* 78 2013-12-12 13:29 26 ******* 79 2013-12-12 13:30 27 ******** 80 2013-12-12 13:31 26 ******* ... ..( 6 skipped). .. ******* 87 2013-12-12 13:38 26 ******* 88 2013-12-12 13:39 27 ******** 89 2013-12-12 13:40 28 ********* SCT Error Recovery Control: Read: 600 (60.0 seconds) Write: 600 (60.0 seconds) SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 4 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 4 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 4 5 Transition from drive PhyRdy to drive PhyNRdy 0x000a 4 6 Device-to-host register FISes sent due to a COMRESET 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0010 2 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 2 0 R_ERR response for host-to-device non-data FIS, non-CRC -V. |
