Menu
▾
▴
Re: [smartmontools-support] badblocks => fine but CurrentPendingSector and OfflineUncorrectableSector disagree
|
From: Bruce A. <ba...@gr...> - 2008-04-12 13:48:30
|
Hi Franck, No SMART Attributes indicate 'dying'. And the self-test does not show any unreadable sectors. So for the moment your disk is OK. However in your place I would keep a close watch on the ATA Error Count. The value is already extremely high (over 6000). On normal disks this number is zero or a handful. In your case these errors are related to unreadable sectors. If they continue to occur, I would definitely replace the disk. Cheers, Bruce On Fri, 11 Apr 2008, Franck Hamelin wrote: > The long test went fine (Extended offline Completed without > error 00% 13078 ) the details are at the end of the reply. > The read error you pointed was probably triggered by the badblocks > according to the time. > > What shall be concluded, is the drive "safe" as long tests and badblocks > suggest or is it "dying" as the smart attribute indicate? > > Franck > > smartctl version 5.36 [i686-pc-linux-gnu] Copyright (C) 2002-6 Bruce Allen > Home page is http://smartmontools.sourceforge.net/ > > === START OF INFORMATION SECTION === > Model Family: Seagate Barracuda 7200.7 and 7200.7 Plus family > Device Model: ST380011A > Serial Number: 5JV9RQZZ > Firmware Version: 3.06 > User Capacity: 80 026 361 856 bytes > Device is: In smartctl database [for details use: -P show] > ATA Version is: 6 > ATA Standard is: ATA/ATAPI-6 T13 1410D revision 2 > Local Time is: Fri Apr 11 15:24:11 2008 CEST > SMART support is: Available - device has SMART capability. > SMART support is: Enabled > > === START OF READ SMART DATA SECTION === > SMART overall-health self-assessment test result: PASSED > > General SMART Values: > Offline data collection status: (0x82) Offline data collection activity > was completed without error. > Auto Offline Data Collection: Enabled. > Self-test execution status: ( 0) The previous self-test > routine completed > without error or no self-test has ever > been run. > Total time to complete Offline > data collection: ( 430) seconds. > Offline data collection > capabilities: (0x5b) SMART execute Offline immediate. > Auto Offline data collection on/off support. > Suspend Offline collection upon new > command. > Offline surface scan supported. > Self-test supported. > No Conveyance Self-test supported. > Selective Self-test supported. > SMART capabilities: (0x0003) Saves SMART data before entering > power-saving mode. > Supports SMART auto save timer. > Error logging capability: (0x01) Error logging supported. > No General Purpose Logging support. > Short self-test routine > recommended polling time: ( 1) minutes. > Extended self-test routine > recommended polling time: ( 58) minutes. > > SMART Attributes Data Structure revision number: 10 > Vendor Specific SMART Attributes with Thresholds: > ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE > UPDATED WHEN_FAILED RAW_VALUE > 1 Raw_Read_Error_Rate 0x000f 054 047 006 Pre-fail > Always - 39067072 > 3 Spin_Up_Time 0x0003 098 098 000 Pre-fail > Always - 0 > 4 Start_Stop_Count 0x0032 100 100 020 Old_age > Always - 0 > 5 Reallocated_Sector_Ct 0x0033 059 059 036 Pre-fail > Always - 1660 > 7 Seek_Error_Rate 0x000f 090 060 030 Pre-fail > Always - 966043501 > 9 Power_On_Hours 0x0032 086 086 000 Old_age > Always - 13078 > 10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail > Always - 0 > 12 Power_Cycle_Count 0x0032 100 100 020 Old_age > Always - 53 > 194 Temperature_Celsius 0x0022 037 061 000 Old_age > Always - 37 > 195 Hardware_ECC_Recovered 0x001a 054 047 000 Old_age > Always - 39067072 > 197 Current_Pending_Sector 0x0012 088 088 000 Old_age > Always - 7081 > 198 Offline_Uncorrectable 0x0010 088 088 000 Old_age > Offline - 7081 > 199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age > Always - 0 > 200 Multi_Zone_Error_Rate 0x0000 100 253 000 Old_age > Offline - 0 > 202 TA_Increase_Count 0x0032 165 062 000 Old_age > Always - 191 > > SMART Error Log Version: 1 > ATA Error Count: 6859 (device log contains only the most recent five errors) > CR = Command Register [HEX] > FR = Features Register [HEX] > SC = Sector Count Register [HEX] > SN = Sector Number Register [HEX] > CL = Cylinder Low Register [HEX] > CH = Cylinder High Register [HEX] > DH = Device/Head Register [HEX] > DC = Device Command Register [HEX] > ER = Error register [HEX] > ST = Status register [HEX] > Powered_Up_Time is measured from power on, and printed as > DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, > SS=sec, and sss=millisec. It "wraps" after 49.710 days. > > Error 6859 occurred at disk power-on lifetime: 13064 hours (544 days + 8 > hours) > When the command that caused the error occurred, the device was active > or idle. > > After command completion occurred, registers were: > ER ST SC SN CL CH DH > -- -- -- -- -- -- -- > 40 51 00 1a 7d 1e f0 Error: UNC at LBA = 0x001e7d1a = 1998106 > > Commands leading to the command that caused the error were: > CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name > -- -- -- -- -- -- -- -- ---------------- -------------------- > 25 00 f8 47 7c 1e f0 00 01:52:38.732 READ DMA EXT > 25 00 00 3f 7c 1e f0 00 01:52:38.723 READ DMA EXT > 25 00 00 3f 7a 1e f0 00 01:52:38.715 READ DMA EXT > 25 00 00 3f 78 1e f0 00 01:52:38.706 READ DMA EXT > 25 00 00 3f 76 1e f0 00 01:52:38.697 READ DMA EXT > > Error 6858 occurred at disk power-on lifetime: 13064 hours (544 days + 8 > hours) > When the command that caused the error occurred, the device was active > or idle. > > After command completion occurred, registers were: > ER ST SC SN CL CH DH > -- -- -- -- -- -- -- > 40 51 00 1a 7d 1e f0 Error: UNC at LBA = 0x001e7d1a = 1998106 > > Commands leading to the command that caused the error were: > CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name > -- -- -- -- -- -- -- -- ---------------- -------------------- > 25 00 00 3f 7c 1e f0 00 01:52:38.732 READ DMA EXT > 25 00 00 3f 7a 1e f0 00 01:52:38.723 READ DMA EXT > 25 00 00 3f 78 1e f0 00 01:52:38.715 READ DMA EXT > 25 00 00 3f 76 1e f0 00 01:52:38.706 READ DMA EXT > 25 00 00 3f 74 1e f0 00 01:52:38.697 READ DMA EXT > > Error 6857 occurred at disk power-on lifetime: 12313 hours (513 days + 1 > hours) > When the command that caused the error occurred, the device was active > or idle. > > After command completion occurred, registers were: > ER ST SC SN CL CH DH > -- -- -- -- -- -- -- > 40 51 00 8d 84 1e f0 Error: UNC at LBA = 0x001e848d = 2000013 > > Commands leading to the command that caused the error were: > CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name > -- -- -- -- -- -- -- -- ---------------- -------------------- > 25 00 70 8a 84 1e f0 00 09:02:04.055 READ DMA EXT > 25 00 78 82 84 1e f0 00 09:01:56.002 READ DMA EXT > 25 00 80 7a 84 1e f0 00 09:01:48.876 READ DMA EXT > 25 00 88 72 84 1e f0 00 09:03:15.781 READ DMA EXT > 25 00 90 6a 84 1e f0 00 09:03:10.826 READ DMA EXT > > Error 6856 occurred at disk power-on lifetime: 12313 hours (513 days + 1 > hours) > When the command that caused the error occurred, the device was active > or idle. > > After command completion occurred, registers were: > ER ST SC SN CL CH DH > -- -- -- -- -- -- -- > 40 51 00 8d 84 1e f0 Error: UNC at LBA = 0x001e848d = 2000013 > > Commands leading to the command that caused the error were: > CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name > -- -- -- -- -- -- -- -- ---------------- -------------------- > 25 00 78 82 84 1e f0 00 09:02:04.055 READ DMA EXT > 25 00 80 7a 84 1e f0 00 09:01:56.002 READ DMA EXT > 25 00 88 72 84 1e f0 00 09:01:48.876 READ DMA EXT > 25 00 90 6a 84 1e f0 00 09:01:41.781 READ DMA EXT > 25 00 98 62 84 1e f0 00 09:03:10.826 READ DMA EXT > > Error 6855 occurred at disk power-on lifetime: 12313 hours (513 days + 1 > hours) > When the command that caused the error occurred, the device was active > or idle. > > After command completion occurred, registers were: > ER ST SC SN CL CH DH > -- -- -- -- -- -- -- > 40 51 00 8d 84 1e f0 Error: UNC at LBA = 0x001e848d = 2000013 > > Commands leading to the command that caused the error were: > CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name > -- -- -- -- -- -- -- -- ---------------- -------------------- > 25 00 80 7a 84 1e f0 00 09:02:04.055 READ DMA EXT > 25 00 88 72 84 1e f0 00 09:01:56.002 READ DMA EXT > 25 00 90 6a 84 1e f0 00 09:01:48.876 READ DMA EXT > 25 00 98 62 84 1e f0 00 09:01:41.781 READ DMA EXT > 25 00 a0 5a 84 1e f0 00 09:01:33.854 READ DMA EXT > > SMART Self-test log structure revision number 1 > Num Test_Description Status Remaining > LifeTime(hours) LBA_of_first_error > # 1 Extended offline Completed without error 00% > 13078 - > # 2 Short offline Completed without error 00% > 13070 - > # 3 Short offline Completed without error 00% > 12726 - > # 4 Extended offline Completed without error 00% > 12704 - > # 5 Short offline Completed without error 00% > 12702 - > # 6 Short offline Completed without error 00% > 12678 - > # 7 Short offline Completed without error 00% > 12655 - > # 8 Short offline Completed without error 00% > 12631 - > # 9 Short offline Completed without error 00% > 12607 - > #10 Short offline Completed without error 00% > 12584 - > #11 Short offline Completed without error 00% > 12560 - > #12 Extended offline Completed without error 00% > 12538 - > #13 Short offline Completed without error 00% > 12536 - > #14 Short offline Completed without error 00% > 12513 - > #15 Short offline Completed without error 00% > 12489 - > #16 Short offline Completed without error 00% > 12466 - > #17 Short offline Completed without error 00% > 12442 - > #18 Short offline Completed without error 00% > 12418 - > #19 Short offline Completed without error 00% > 12395 - > #20 Extended offline Interrupted (host reset) 90% > 12379 - > #21 Short offline Completed without error 00% > 12371 - > > SMART Selective self-test log data structure revision number 1 > SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS > 1 0 0 Not_testing > 2 0 0 Not_testing > 3 0 0 Not_testing > 4 0 0 Not_testing > 5 0 0 Not_testing > Selective self-test flags (0x0): > After scanning selected spans, do NOT read-scan remainder of disk. > If Selective self-test is pending on power-up, resume after 0 minute delay. > > > > Bruce Allen wrote : >> Your drive last had trouble reading a sector 17 hours ago. I suggest >> that you run a long self-test '-t long' and see if there are any >> unreadable sectors now. >> >> Your drive appears to be one of those that does not reset the >> uncorrectable sector counters to zero. So you may need to configure >> smartd to ignore those atributes. >> >> badblocks does not read the entire disk surface, but a '-t long' test >> will do this. >> >> Bruce >> >> >> On Fri, 11 Apr 2008, Franck Hamelin wrote: >> >>> Hi, >>> >>> hdd , a 80 Go pata Seagate Barracuda 7200.7., 1 linux partition (full >>> disk) >>> mke2fs with -c -c (bad blocks read-write test) => everything fine >>> but (after the periodical test of smartd) 7081 Currently unreadable >>> (pending) sectors and 7081 Offline uncorrectable sectors >>> >>> "Bad block HOWTO for smartmontools" and web search seems to indicate >>> that writing to the sector shall trigger reallocation and therefore the >>> smart attributes shall comes back to 0. >>> >>> I'd appreciate some help for the interpretation. >>> >>> - what can explain the "incoherence" of no bad blocks (according to >>> badblocks write test) and the smart attributes CurrentPendingSector and >>> OfflineUncorrectableSector with non zero value? >>> >>> - Should that drive be considered healthy or not? >>> >>> Best regards, >>> >>> Franck >>> >>> #smartctl -a /dev/hdd >>> smartctl version 5.36 [i686-pc-linux-gnu] Copyright (C) 2002-6 Bruce >>> Allen >>> Home page is http://smartmontools.sourceforge.net/ >>> >>> === START OF INFORMATION SECTION === >>> Model Family: Seagate Barracuda 7200.7 and 7200.7 Plus family >>> Device Model: ST380011A >>> Serial Number: 5JV9RQZZ >>> Firmware Version: 3.06 >>> User Capacity: 80 026 361 856 bytes >>> Device is: In smartctl database [for details use: -P show] >>> ATA Version is: 6 >>> ATA Standard is: ATA/ATAPI-6 T13 1410D revision 2 >>> Local Time is: Fri Apr 11 14:02:05 2008 CEST >>> SMART support is: Available - device has SMART capability. >>> SMART support is: Enabled >>> >>> === START OF READ SMART DATA SECTION === >>> SMART overall-health self-assessment test result: PASSED >>> >>> General SMART Values: >>> Offline data collection status: (0x82) Offline data collection >>> activity >>> was completed without error. >>> Auto Offline Data Collection: Enabled. >>> Self-test execution status: ( 0) The previous self-test >>> routine completed >>> without error or no self-test has ever >>> been run. >>> Total time to complete Offline >>> data collection: ( 430) seconds. >>> Offline data collection >>> capabilities: (0x5b) SMART execute Offline immediate. >>> Auto Offline data collection on/off support. >>> Suspend Offline collection upon new >>> command. >>> Offline surface scan supported. >>> Self-test supported. >>> No Conveyance Self-test supported. >>> Selective Self-test supported. >>> SMART capabilities: (0x0003) Saves SMART data before >>> entering >>> power-saving mode. >>> Supports SMART auto save timer. >>> Error logging capability: (0x01) Error logging supported. >>> No General Purpose Logging support. >>> Short self-test routine >>> recommended polling time: ( 1) minutes. >>> Extended self-test routine >>> recommended polling time: ( 58) minutes. >>> >>> SMART Attributes Data Structure revision number: 10 >>> Vendor Specific SMART Attributes with Thresholds: >>> ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE >>> UPDATED WHEN_FAILED RAW_VALUE >>> 1 Raw_Read_Error_Rate 0x000f 054 047 006 Pre-fail >>> Always - 87596309 >>> 3 Spin_Up_Time 0x0003 098 098 000 Pre-fail >>> Always - 0 >>> 4 Start_Stop_Count 0x0032 100 100 020 Old_age >>> Always - 0 >>> 5 Reallocated_Sector_Ct 0x0033 059 059 036 Pre-fail >>> Always - 1660 >>> 7 Seek_Error_Rate 0x000f 090 060 030 Pre-fail >>> Always - 965780377 >>> 9 Power_On_Hours 0x0032 086 086 000 Old_age >>> Always - 13077 >>> 10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail >>> Always - 0 >>> 12 Power_Cycle_Count 0x0032 100 100 020 Old_age >>> Always - 53 >>> 194 Temperature_Celsius 0x0022 032 061 000 Old_age >>> Always - 32 >>> 195 Hardware_ECC_Recovered 0x001a 054 047 000 Old_age >>> Always - 87596309 >>> 197 Current_Pending_Sector 0x0012 088 088 000 Old_age >>> Always - 7081 >>> 198 Offline_Uncorrectable 0x0010 088 088 000 Old_age >>> Offline - 7081 >>> 199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age >>> Always - 0 >>> 200 Multi_Zone_Error_Rate 0x0000 100 253 000 Old_age >>> Offline - 0 >>> 202 TA_Increase_Count 0x0032 165 062 000 Old_age >>> Always - 191 >>> >>> SMART Error Log Version: 1 >>> ATA Error Count: 6859 (device log contains only the most recent five >>> errors) >>> CR = Command Register [HEX] >>> FR = Features Register [HEX] >>> SC = Sector Count Register [HEX] >>> SN = Sector Number Register [HEX] >>> CL = Cylinder Low Register [HEX] >>> CH = Cylinder High Register [HEX] >>> DH = Device/Head Register [HEX] >>> DC = Device Command Register [HEX] >>> ER = Error register [HEX] >>> ST = Status register [HEX] >>> Powered_Up_Time is measured from power on, and printed as >>> DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, >>> SS=sec, and sss=millisec. It "wraps" after 49.710 days. >>> >>> Error 6859 occurred at disk power-on lifetime: 13064 hours (544 days + 8 >>> hours) >>> When the command that caused the error occurred, the device was active >>> or idle. >>> >>> After command completion occurred, registers were: >>> ER ST SC SN CL CH DH >>> -- -- -- -- -- -- -- >>> 40 51 00 1a 7d 1e f0 Error: UNC at LBA = 0x001e7d1a = 1998106 >>> >>> Commands leading to the command that caused the error were: >>> CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name >>> -- -- -- -- -- -- -- -- ---------------- -------------------- >>> 25 00 f8 47 7c 1e f0 00 01:52:38.732 READ DMA EXT >>> 25 00 00 3f 7c 1e f0 00 01:52:38.723 READ DMA EXT >>> 25 00 00 3f 7a 1e f0 00 01:52:38.715 READ DMA EXT >>> 25 00 00 3f 78 1e f0 00 01:52:38.706 READ DMA EXT >>> 25 00 00 3f 76 1e f0 00 01:52:38.697 READ DMA EXT >>> >>> Error 6858 occurred at disk power-on lifetime: 13064 hours (544 days + 8 >>> hours) >>> When the command that caused the error occurred, the device was active >>> or idle. >>> >>> After command completion occurred, registers were: >>> ER ST SC SN CL CH DH >>> -- -- -- -- -- -- -- >>> 40 51 00 1a 7d 1e f0 Error: UNC at LBA = 0x001e7d1a = 1998106 >>> >>> Commands leading to the command that caused the error were: >>> CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name >>> -- -- -- -- -- -- -- -- ---------------- -------------------- >>> 25 00 00 3f 7c 1e f0 00 01:52:38.732 READ DMA EXT >>> 25 00 00 3f 7a 1e f0 00 01:52:38.723 READ DMA EXT >>> 25 00 00 3f 78 1e f0 00 01:52:38.715 READ DMA EXT >>> 25 00 00 3f 76 1e f0 00 01:52:38.706 READ DMA EXT >>> 25 00 00 3f 74 1e f0 00 01:52:38.697 READ DMA EXT >>> >>> Error 6857 occurred at disk power-on lifetime: 12313 hours (513 days + 1 >>> hours) >>> When the command that caused the error occurred, the device was active >>> or idle. >>> >>> After command completion occurred, registers were: >>> ER ST SC SN CL CH DH >>> -- -- -- -- -- -- -- >>> 40 51 00 8d 84 1e f0 Error: UNC at LBA = 0x001e848d = 2000013 >>> >>> Commands leading to the command that caused the error were: >>> CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name >>> -- -- -- -- -- -- -- -- ---------------- -------------------- >>> 25 00 70 8a 84 1e f0 00 09:02:04.055 READ DMA EXT >>> 25 00 78 82 84 1e f0 00 09:01:56.002 READ DMA EXT >>> 25 00 80 7a 84 1e f0 00 09:01:48.876 READ DMA EXT >>> 25 00 88 72 84 1e f0 00 09:03:15.781 READ DMA EXT >>> 25 00 90 6a 84 1e f0 00 09:03:10.826 READ DMA EXT >>> >>> Error 6856 occurred at disk power-on lifetime: 12313 hours (513 days + 1 >>> hours) >>> When the command that caused the error occurred, the device was active >>> or idle. >>> >>> After command completion occurred, registers were: >>> ER ST SC SN CL CH DH >>> -- -- -- -- -- -- -- >>> 40 51 00 8d 84 1e f0 Error: UNC at LBA = 0x001e848d = 2000013 >>> >>> Commands leading to the command that caused the error were: >>> CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name >>> -- -- -- -- -- -- -- -- ---------------- -------------------- >>> 25 00 78 82 84 1e f0 00 09:02:04.055 READ DMA EXT >>> 25 00 80 7a 84 1e f0 00 09:01:56.002 READ DMA EXT >>> 25 00 88 72 84 1e f0 00 09:01:48.876 READ DMA EXT >>> 25 00 90 6a 84 1e f0 00 09:01:41.781 READ DMA EXT >>> 25 00 98 62 84 1e f0 00 09:03:10.826 READ DMA EXT >>> >>> Error 6855 occurred at disk power-on lifetime: 12313 hours (513 days + 1 >>> hours) >>> When the command that caused the error occurred, the device was active >>> or idle. >>> >>> After command completion occurred, registers were: >>> ER ST SC SN CL CH DH >>> -- -- -- -- -- -- -- >>> 40 51 00 8d 84 1e f0 Error: UNC at LBA = 0x001e848d = 2000013 >>> >>> Commands leading to the command that caused the error were: >>> CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name >>> -- -- -- -- -- -- -- -- ---------------- -------------------- >>> 25 00 80 7a 84 1e f0 00 09:02:04.055 READ DMA EXT >>> 25 00 88 72 84 1e f0 00 09:01:56.002 READ DMA EXT >>> 25 00 90 6a 84 1e f0 00 09:01:48.876 READ DMA EXT >>> 25 00 98 62 84 1e f0 00 09:01:41.781 READ DMA EXT >>> 25 00 a0 5a 84 1e f0 00 09:01:33.854 READ DMA EXT >>> >>> SMART Self-test log structure revision number 1 >>> Num Test_Description Status Remaining >>> LifeTime(hours) LBA_of_first_error >>> # 1 Short offline Completed without error 00% >>> 13070 - >>> # 2 Short offline Completed without error 00% >>> 12726 - >>> # 3 Extended offline Completed without error 00% >>> 12704 - >>> # 4 Short offline Completed without error 00% >>> 12702 - >>> # 5 Short offline Completed without error 00% >>> 12678 - >>> # 6 Short offline Completed without error 00% >>> 12655 - >>> # 7 Short offline Completed without error 00% >>> 12631 - >>> # 8 Short offline Completed without error 00% >>> 12607 - >>> # 9 Short offline Completed without error 00% >>> 12584 - >>> #10 Short offline Completed without error 00% >>> 12560 - >>> #11 Extended offline Completed without error 00% >>> 12538 - >>> #12 Short offline Completed without error 00% >>> 12536 - >>> #13 Short offline Completed without error 00% >>> 12513 - >>> #14 Short offline Completed without error 00% >>> 12489 - >>> #15 Short offline Completed without error 00% >>> 12466 - >>> #16 Short offline Completed without error 00% >>> 12442 - >>> #17 Short offline Completed without error 00% >>> 12418 - >>> #18 Short offline Completed without error 00% >>> 12395 - >>> #19 Extended offline Interrupted (host reset) 90% >>> 12379 - >>> #20 Short offline Completed without error 00% >>> 12371 - >>> #21 Extended offline Completed without error 00% >>> 12334 - >>> >>> SMART Selective self-test log data structure revision number 1 >>> SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS >>> 1 0 0 Not_testing >>> 2 0 0 Not_testing >>> 3 0 0 Not_testing >>> 4 0 0 Not_testing >>> 5 0 0 Not_testing >>> Selective self-test flags (0x0): >>> After scanning selected spans, do NOT read-scan remainder of disk. >>> If Selective self-test is pending on power-up, resume after 0 minute >>> delay. >>> >>> >>> >>> ------------------------------------------------------------------------- >>> >>> This SF.net email is sponsored by the 2008 JavaOne(SM) Conference >>> Don't miss this year's exciting event. There's still time to save $100. >>> Use priority code J8TL2D2. >>> http://ad.doubleclick.net/clk;198757673;13503038;p?http://java.sun.com/javaone >>> >>> _______________________________________________ >>> Smartmontools-support mailing list >>> Sma...@li... >>> https://lists.sourceforge.net/lists/listinfo/smartmontools-support >>> >> >> > > > ------------------------------------------------------------------------- > This SF.net email is sponsored by the 2008 JavaOne(SM) Conference > Don't miss this year's exciting event. There's still time to save $100. > Use priority code J8TL2D2. > http://ad.doubleclick.net/clk;198757673;13503038;p?http://java.sun.com/javaone > _______________________________________________ > Smartmontools-support mailing list > Sma...@li... > https://lists.sourceforge.net/lists/listinfo/smartmontools-support > |
