From: Joya L. M. <feo...@my...> - 2007-10-26 18:50:12
|
I get messages like this for months: Oct 26 15:50:03 localhost smartd[2792]: Device: /dev/hdb, ATA error count increased from 6875 to 6876 (I've noticed I get this messages after the computer resumed from hibernate) But the drive passes short and long tests and it doesn't show LBA errors. here is the output of smartctl -a Should I start to searching a new drive? #smartctl -a /dev/hdb1 smartctl version 5.36 [i686-pc-linux-gnu] Copyright (C) 2002-6 Bruce Allen Home page is http://smartmontools.sourceforge.net/ === START OF INFORMATION SECTION === Device Model: SAMSUNG SV0412H Serial Number: 0575J1DW609001 Firmware Version: SK300-15 User Capacity: 40.060.403.712 bytes Device is: In smartctl database [for details use: -P show] ATA Version is: 6 ATA Standard is: ATA/ATAPI-6 T13 1410D revision 1 Local Time is: Fri Oct 26 20:42:01 2007 EEST ==> WARNING: May need -F samsung disabled; see manual for details. SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (1920) seconds. Offline data collection capabilities: (0x1b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. No Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. No General Purpose Logging support. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 32) minutes. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000a 100 100 000 Old_age Always - 399 4 Start_Stop_Count 0x0032 097 097 000 Old_age Always - 3597 5 Reallocated_Sector_Ct 0x0033 253 253 009 Pre-fail Always - 0 7 Seek_Error_Rate 0x000b 253 253 051 Pre-fail Always - 0 8 Seek_Time_Performance 0x0024 253 253 000 Old_age Offline - 0 9 Power_On_Half_Minutes 0x0032 100 100 000 Old_age Always - 4969h+54m 12 Power_Cycle_Count 0x0032 099 099 000 Old_age Always - 1729 194 Temperature_Celsius_x10 0x0022 178 100 000 Old_age Always - 25.0 197 Current_Pending_Sector 0x0033 253 253 009 Pre-fail Always - 0 198 Offline_Uncorrectable 0x0031 253 253 009 Pre-fail Offline - 0 199 UDMA_CRC_Error_Count 0x000a 100 100 000 Old_age Always - 0 200 Multi_Zone_Error_Rate 0x000b 100 100 051 Pre-fail Always - 0 201 Soft_Read_Error_Rate 0x000b 100 100 051 Pre-fail Always - 0 SMART Error Log Version: 1 Warning: ATA error count 6876 inconsistent with error log pointer 5 ATA Error Count: 6876 (device log contains only the most recent five errors) CR = Command Register [HEX] FR = Features Register [HEX] SC = Sector Count Register [HEX] SN = Sector Number Register [HEX] CL = Cylinder Low Register [HEX] CH = Cylinder High Register [HEX] DH = Device/Head Register [HEX] DC = Device Command Register [HEX] ER = Error register [HEX] ST = Status register [HEX] Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 6876 occurred at disk power-on lifetime: 4966 hours (206 days + 22 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 04 51 05 01 00 00 b0 Error: ABRT Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- a1 00 05 01 00 00 b0 00 00:00:12.000 IDENTIFY PACKET DEVICE e0 00 00 00 00 00 f0 00 01:16:56.000 STANDBY IMMEDIATE e7 00 00 00 00 00 f0 00 01:16:56.000 FLUSH CACHE ca 00 08 38 69 e1 f4 00 01:16:56.000 WRITE DMA ca 00 08 00 69 d1 f4 00 01:16:56.000 WRITE DMA Error 6875 occurred at disk power-on lifetime: 4965 hours (206 days + 21 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 04 51 05 01 00 00 b0 Error: ABRT Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- a1 00 05 01 00 00 b0 00 00:00:12.000 IDENTIFY PACKET DEVICE e0 00 00 00 00 00 f0 00 01:36:04.000 STANDBY IMMEDIATE e7 00 00 00 00 00 f0 00 01:36:04.000 FLUSH CACHE ca 00 08 70 7a 1d f4 00 01:36:04.000 WRITE DMA ca 00 08 00 69 d1 f4 00 01:36:04.000 WRITE DMA Error 6874 occurred at disk power-on lifetime: 4964 hours (206 days + 20 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 04 51 05 01 00 00 b0 Error: ABRT Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- a1 00 05 01 00 00 b0 00 00:00:12.000 IDENTIFY PACKET DEVICE e0 00 00 00 00 00 f0 00 01:07:05.000 STANDBY IMMEDIATE e7 00 00 00 00 00 f0 00 01:07:05.000 FLUSH CACHE ca 00 08 28 7a 1c f4 00 01:07:05.000 WRITE DMA ca 00 08 00 69 d1 f4 00 01:07:05.000 WRITE DMA Error 6873 occurred at disk power-on lifetime: 4963 hours (206 days + 19 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 04 51 05 01 00 00 b0 Error: ABRT Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- a1 00 05 01 00 00 b0 00 00:00:12.000 IDENTIFY PACKET DEVICE e0 00 00 00 00 00 f0 00 01:10:59.000 STANDBY IMMEDIATE e7 00 00 00 00 00 f0 00 01:10:58.000 FLUSH CACHE ca 00 08 40 7a 1a f4 00 01:10:58.000 WRITE DMA ca 00 08 00 69 d1 f4 00 01:10:58.000 WRITE DMA Error 6872 occurred at disk power-on lifetime: 4962 hours (206 days + 18 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 04 51 05 01 00 00 b0 Error: ABRT Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- a1 00 05 01 00 00 b0 00 00:00:12.000 IDENTIFY PACKET DEVICE e0 00 00 00 00 00 f0 00 00:42:28.000 STANDBY IMMEDIATE e7 00 00 00 00 00 f0 00 00:42:28.000 FLUSH CACHE ca 00 08 40 7a 1a f4 00 00:42:28.000 WRITE DMA ca 00 08 00 69 d1 f4 00 00:42:28.000 WRITE DMA SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Completed without error 00% 4960 - # 2 Extended offline Completed without error 00% 4960 - # 3 Short offline Completed without error 00% 4195 - Device does not support Selective Self Tests/Logging |