[Serial-pci-info] lspci -vv
Brought to you by:
tytso
Menu
▾
▴
[Serial-pci-info] lspci -vv
|
From: George P. <ge...@st...> - 2004-04-01 09:44:14
|
Serial Card is digitus (www.digitus.info) Model DCSER2 OUTPUT OF dmesg : Serial driver version 5.05c (2001-07-08) with HUB-6 MANY_PORTS MULTIPORT SHARE_IRQ SERIAL_PCI enabled ttyS00 at 0x03f8 (irq = 4) is a 16550A ttyS01 at 0x02f8 (irq = 3) is a 16550A Redundant entry in serial pci_table. Please send the output of lspci -vv, this message (1409,7168,1409,4037) and the manufacturer and name of serial board or modem board to ser...@li.... ttyS04 at port 0xbc00 (irq = 22) is a 16550A ttyS05 at port 0xbc08 (irq = 22) is a 16550A lspci -vv : 00:00.0 Host bridge: Intel Corp.: Unknown device 2578 (rev 02) Subsystem: Intel Corp.: Unknown device 2578 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- Latency: 0 Region 0: Memory at f8000000 (32-bit, prefetchable) [size=64M] Capabilities: [e4] #09 [2106] Capabilities: [a0] AGP version 3.0 Status: RQ=31 SBA+ 64bit- FW+ Rate=x1,x2 Command: RQ=0 SBA- AGP- 64bit- FW- Rate=<none> 00:01.0 PCI bridge: Intel Corp.: Unknown device 2579 (rev 02) (prog-if 00 [Normal decode]) Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap- 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32 Bus: primary=00, secondary=01, subordinate=01, sec-latency=32 BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B- 00:03.0 PCI bridge: Intel Corp.: Unknown device 257b (rev 02) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap- 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32 Bus: primary=00, secondary=02, subordinate=02, sec-latency=0 I/O behind bridge: 0000a000-0000afff Memory behind bridge: fc900000-fc9fffff BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B- 00:1d.0 USB Controller: Intel Corp.: Unknown device 24d2 (rev 02) (prog-if 00 [UHCI]) Subsystem: Intel Corp.: Unknown device 3428 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Interrupt: pin A routed to IRQ 16 Region 4: I/O ports at cc00 [size=32] 00:1d.1 USB Controller: Intel Corp.: Unknown device 24d4 (rev 02) (prog-if 00 [UHCI]) Subsystem: Intel Corp.: Unknown device 3428 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Interrupt: pin B routed to IRQ 19 Region 4: I/O ports at d000 [size=32] 00:1d.2 USB Controller: Intel Corp.: Unknown device 24d7 (rev 02) (prog-if 00 [UHCI]) Subsystem: Intel Corp.: Unknown device 3428 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Interrupt: pin C routed to IRQ 18 Region 4: I/O ports at d400 [size=32] 00:1d.3 USB Controller: Intel Corp.: Unknown device 24de (rev 02) (prog-if 00 [UHCI]) Subsystem: Intel Corp.: Unknown device 3428 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Interrupt: pin A routed to IRQ 16 Region 4: I/O ports at d800 [size=32] 00:1d.7 USB Controller: Intel Corp.: Unknown device 24dd (rev 02) (prog-if 20) Subsystem: Intel Corp.: Unknown device 3428 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Interrupt: pin D routed to IRQ 23 Region 0: Memory at febffc00 (32-bit, non-prefetchable) [size=1K] Capabilities: [50] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [58] #0a [20a0] 00:1e.0 PCI bridge: Intel Corp. 82820 820 (Camino 2) Chipset PCI (rev c2) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Bus: primary=00, secondary=03, subordinate=03, sec-latency=32 I/O behind bridge: 0000b000-0000bfff Memory behind bridge: fca00000-feafffff BridgeCtl: Parity- SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B- 00:1f.0 ISA bridge: Intel Corp.: Unknown device 24d0 (rev 02) Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 00:1f.1 IDE interface: Intel Corp.: Unknown device 24db (rev 02) (prog-if 8a [Master SecP PriP]) Subsystem: Intel Corp.: Unknown device 3428 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Interrupt: pin A routed to IRQ 18 Region 0: I/O ports at <unassigned> Region 1: I/O ports at <unassigned> Region 2: I/O ports at <unassigned> Region 3: I/O ports at <unassigned> Region 4: I/O ports at ffa0 [size=16] Region 5: Memory at 20000000 (32-bit, non-prefetchable) [size=1K] 00:1f.2 IDE interface: Intel Corp.: Unknown device 24d1 (rev 02) (prog-if 8f [Master SecP SecO PriP PriO]) Subsystem: Intel Corp.: Unknown device 3428 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Interrupt: pin A routed to IRQ 18 Region 0: I/O ports at ec00 [size=8] Region 1: I/O ports at e800 [size=4] Region 2: I/O ports at e400 [size=8] Region 3: I/O ports at e000 [size=4] Region 4: I/O ports at dc00 [size=16] 00:1f.3 SMBus: Intel Corp.: Unknown device 24d3 (rev 02) Subsystem: Intel Corp.: Unknown device 3428 Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Interrupt: pin B routed to IRQ 17 Region 4: I/O ports at c800 [size=32] 02:01.0 Ethernet controller: Intel Corp.: Unknown device 1019 Subsystem: Intel Corp.: Unknown device 3428 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 (63750ns min), cache line size 08 Interrupt: pin A routed to IRQ 18 Region 0: Memory at fc9e0000 (32-bit, non-prefetchable) [size=128K] Region 2: I/O ports at ac00 [size=32] Capabilities: [dc] Power Management version 2 Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=1 PME- 03:01.0 Serial controller: Timedia Technology Co Ltd: Unknown device 7168 (rev 01) (prog-if 02 [16550]) Subsystem: Timedia Technology Co Ltd: Unknown device 4037 Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR+ FastB2B- Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Interrupt: pin A routed to IRQ 22 Region 0: I/O ports at bc00 [size=32] 03:06.0 VGA compatible controller: ATI Technologies Inc Rage XL (rev 27) (prog-if 00 [VGA]) Subsystem: Intel Corp.: Unknown device 3428 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32 (2000ns min), cache line size 08 Interrupt: pin A routed to IRQ 20 Region 0: Memory at fd000000 (32-bit, non-prefetchable) [size=16M] Region 1: I/O ports at b800 [size=256] Region 2: Memory at feaff000 (32-bit, non-prefetchable) [size=4K] Expansion ROM at feac0000 [disabled] [size=128K] Capabilities: [5c] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 03:08.0 Ethernet controller: Intel Corp.: Unknown device 1050 (rev 01) Subsystem: Intel Corp.: Unknown device 3428 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32 (2000ns min, 14000ns max), cache line size 08 Interrupt: pin A routed to IRQ 20 Region 0: Memory at feafe000 (32-bit, non-prefetchable) [size=4K] Region 1: I/O ports at b400 [size=64] Capabilities: [dc] Power Management version 2 Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=2 PME- George |
