[Serial-pci-info] lspci -vv
Brought to you by:
tytso
Menu
▾
▴
[Serial-pci-info] lspci -vv
|
From: Muhammad A. \(AKI\) <ak...@d-...> - 2003-10-24 03:13:55
|
I have a Thinkpad T20, everytime I try to install any flavour of linux it tries to load the kernel but gets to the below message and then goes no further... I eventually found that Debian (woody) network install CD seems to install fine, and would operate wih no problems until I upgraded to the current kernel version 2.4.22, now it tries to again load the kernel, gets to the below message and then hangs, stoopidly I didn't create a boot floppy to boot from my previous kernel version... BOOT ERROR MESSAGE Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI ISAPNP enabled PCI: Found IRQ 7 for device 00:03.1 PCI: Sharing IRQ 7 with 00:03.0 Redundant entry in serial pci_table. Please send the output of lspci -vv, this message (115d,000c,8086,2408) and the manufacturer and name of serial board or modem board to ser...@li... I believe it is the Xircom 56k Win Global (modem) that is causing the problem... ...I do however, after several reboots and several changes to bios settings manage to boot with the new kernel, but on a subsequent reboot suffer with the same problem... I managad to get a an lspci -vv output and a dmesg output which I have included. Please help my cause, I don't want a do$e laptop... Many thanks aki;) ak...@d-... DMESG OUTPUT Linux version 2.4.22 (root@tornado) (gcc version 2.95.4 20011002 (Debian prerelease)) #1 SMP Tue Oct 21 12:21:14 BST 2003 BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009f800 (usable) BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved) BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 0000000007ff0000 (usable) BIOS-e820: 0000000007ff0000 - 0000000007ffec00 (ACPI data) BIOS-e820: 0000000007ffec00 - 0000000008000000 (ACPI NVS) BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved) 127MB LOWMEM available. On node 0 totalpages: 32752 zone(0): 4096 pages. zone(1): 28656 pages. zone(2): 0 pages. IBM machine detected. Enabling interrupts during APM calls. Kernel command line: auto BOOT_IMAGE=Linux ro root=301 Local APIC disabled by BIOS -- reenabling. Could not enable APIC! Initializing CPU#0 Detected 696.989 MHz processor. Console: colour VGA+ 80x25 Calibrating delay loop... 1389.36 BogoMIPS Memory: 126404k/131008k available (1574k kernel code, 4216k reserved, 672k data, 112k init, 0k highmem) Dentry cache hash table entries: 16384 (order: 5, 131072 bytes) Inode cache hash table entries: 8192 (order: 4, 65536 bytes) Mount cache hash table entries: 512 (order: 0, 4096 bytes) Buffer cache hash table entries: 4096 (order: 2, 16384 bytes) Page-cache hash table entries: 32768 (order: 5, 131072 bytes) CPU: L1 I cache: 16K, L1 D cache: 16K CPU: L2 cache: 256K CPU serial number disabled. Intel machine check architecture supported. Intel machine check reporting enabled on CPU#0. CPU: After generic, caps: 0383f9ff 00000000 00000000 00000000 CPU: Common caps: 0383f9ff 00000000 00000000 00000000 Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. Checking 'hlt' instruction... OK. POSIX conformance testing by UNIFIX CPU: L1 I cache: 16K, L1 D cache: 16K CPU: L2 cache: 256K Intel machine check reporting enabled on CPU#0. CPU: After generic, caps: 0383f9ff 00000000 00000000 00000000 CPU: Common caps: 0383f9ff 00000000 00000000 00000000 CPU0: Intel Pentium III (Coppermine) stepping 03 per-CPU timeslice cutoff: 731.76 usecs. SMP motherboard not detected. Local APIC not detected. Using dummy APIC emulation. Waiting on wait_init_idle (map = 0x0) All processors have done init_idle PCI: PCI BIOS revision 2.10 entry at 0xfd94f, last bus=7 PCI: Using configuration type 1 PCI: Probing PCI hardware PCI: Probing PCI hardware (bus 00) PCI: Discovered primary peer bus 08 [IRQ] PCI: Using IRQ router PIIX [8086/7110] at 00:07.0 Limiting direct PCI/PCI transfers. isapnp: Scanning for PnP cards... isapnp: No Plug & Play device found Linux NET4.0 for Linux 2.4 Based upon Swansea University Computer Society NET3.039 Initializing RT netlink socket Starting kswapd Journalled Block Device driver loaded Installing knfsd (copyright (C) 1996 ok...@mo...). NTFS driver v1.1.22 [Flags: R/O] pty: 256 Unix98 ptys configured Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI ISAPNP enabled PCI: Found IRQ 7 for device 00:03.1 PCI: Sharing IRQ 7 with 00:03.0 Redundant entry in serial pci_table. Please send the output of lspci -vv, this message (115d,000c,8086,2408) and the manufacturer and name of serial board or modem board to ser...@li.... register_serial(): autoconfig failed Floppy drive(s): fd0 is 1.44M FDC 0 is a National Semiconductor PC87306 eepro100.c:v1.09j-t 9/29/99 Donald Becker http://www.scyld.com/network/eepro100.html eepro100.c: $Revision: 1.36 $ 2000/11/17 Modified by Andrey V. Savochkin <sa...@sa...> and others PCI: Found IRQ 7 for device 00:03.0 PCI: Sharing IRQ 7 with 00:03.1 eth0: OEM i82557/i82558 10/100 Ethernet, 00:03:47:0F:86:F6, IRQ 7. Board assembly 000695-001, Physical connectors present: RJ45 Primary interface chip i82555 PHY #1. General self-test: passed. Serial sub-system self-test: passed. Internal registers self-test: passed. ROM checksum self-test: passed (0xdbd8681d). Linux agpgart interface v0.99 (c) Jeff Hartmann agpgart: Maximum main memory to use for agp memory: 94M agpgart: Detected Intel 440BX chipset agpgart: AGP aperture is 64M @ 0xf8000000 Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx PIIX4: IDE controller at PCI slot 00:07.1 PIIX4: chipset revision 1 PIIX4: not 100% native mode: will probe irqs later ide0: BM-DMA at 0x1850-0x1857, BIOS settings: hda:DMA, hdb:pio ide1: BM-DMA at 0x1858-0x185f, BIOS settings: hdc:DMA, hdd:pio hda: IBM-DJSA-220, ATA DISK drive blk: queue c039ea20, I/O limit 4095Mb (mask 0xffffffff) hdc: HITACHI DVD-ROM GD-S200, ATAPI CD/DVD-ROM drive ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 ide1 at 0x170-0x177,0x376 on irq 15 hda: attached ide-disk driver. hda: host protected area => 1 hda: 23572080 sectors (12069 MB) w/1874KiB Cache, CHS=1559/240/63, UDMA(33) hdc: attached ide-cdrom driver. hdc: ATAPI 24X DVD-ROM drive, 512kB Cache, UDMA(33) Uniform CD-ROM driver Revision: 3.12 Partition check: hda: hda1 hda2 hda3 < hda5 > SCSI subsystem driver Revision: 1.00 kmod: failed to exec /sbin/modprobe -s -k scsi_hostadapter, errno = 2 Linux Kernel Card Services 3.1.22 options: [pci] [cardbus] [pm] PCI: Found IRQ 11 for device 00:02.0 PCI: Sharing IRQ 11 with 00:05.0 PCI: Sharing IRQ 11 with 01:00.0 PCI: Found IRQ 9 for device 00:02.1 usb.c: registered new driver hub Yenta IRQ list 0428, PCI irq11 Socket status: 30000006 Yenta IRQ list 0428, PCI irq9 Socket status: 30000006 host/uhci.c: USB Universal Host Controller Interface driver v1.1 PCI: Found IRQ 4 for device 00:07.2 host/uhci.c: USB UHCI at I/O 0x1860, IRQ 4 usb.c: new USB bus registered, assigned bus number 1 hub.c: USB hub found hub.c: 2 ports detected usb.c: registered new driver hid hid-core.c: v1.8.1 Andreas Gal, Vojtech Pavlik <vo...@su...> hid-core.c: USB HID support drivers Initializing USB Mass Storage driver... usb.c: registered new driver usb-storage USB Mass Storage support registered. NET4: Linux TCP/IP 1.0 for NET4.0 IP Protocols: ICMP, UDP, TCP, IGMP IP: routing cache hash table of 512 buckets, 4Kbytes TCP: Hash tables configured (established 8192 bind 8192) IPv4 over IPv4 tunneling driver GRE over IPv4 tunneling driver NET4: Unix domain sockets 1.0/SMP for Linux NET4.0. VFS: Mounted root (ext2 filesystem) readonly. Freeing unused kernel memory: 112k freed Adding Swap: 2097136k swap-space (priority -1) PCI: Found IRQ 11 for device 00:05.0 PCI: Sharing IRQ 11 with 00:02.0 PCI: Sharing IRQ 11 with 01:00.0 Crystal 4280/46xx + AC97 Audio, version 1.28.32, 12:28:18 Oct 21 2003 cs46xx: Card found at 0xe8122000 and 0xe8000000, IRQ 11 cs46xx: Thinkpad 600X/A20/T20 (1014:0153) at 0xe8122000/0xe8000000, IRQ 11 ac97_codec: AC97 Audio codec, id: CRY20 (Cirrus Logic CS4297A rev B) cs: IO port probe 0x0c00-0x0cff: clean. cs: IO port probe 0x0800-0x08ff: clean. cs: IO port probe 0x0100-0x04ff: excluding 0x4d0-0x4d7 cs: IO port probe 0x0a00-0x0aff: clean. LSPCI -VV OUTPUT 00:00.0 Host bridge: Intel Corp. 440BX/ZX - 82443BX/ZX Host bridge (rev 03) Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR- Latency: 64 Region 0: Memory at f8000000 (32-bit, prefetchable) [size=64M] Capabilities: <available only to root> 00:01.0 PCI bridge: Intel Corp. 440BX/ZX - 82443BX/ZX AGP bridge (rev 03) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 128 Bus: primary=00, secondary=01, subordinate=01, sec-latency=64 Memory behind bridge: f0000000-f7ffffff BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B+ 00:02.0 CardBus bridge: Texas Instruments PCI1450 (rev 03) Subsystem: IBM: Unknown device 0130 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 168, cache line size 08 Interrupt: pin A routed to IRQ 10 Region 0: Memory at 50000000 (32-bit, non-prefetchable) [size=4K] Bus: primary=00, secondary=02, subordinate=04, sec-latency=176 Memory window 0: 10000000-103ff000 (prefetchable) Memory window 1: 10400000-107ff000 I/O window 0: 00004000-000040ff I/O window 1: 00004400-000044ff BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ PostWrite+ 16-bit legacy interface ports at 0001 00:02.1 CardBus bridge: Texas Instruments PCI1450 (rev 03) Subsystem: IBM: Unknown device 0130 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 168, cache line size 08 Interrupt: pin B routed to IRQ 10 Region 0: Memory at 50100000 (32-bit, non-prefetchable) [size=4K] Bus: primary=00, secondary=05, subordinate=07, sec-latency=176 Memory window 0: 10800000-10bff000 (prefetchable) Memory window 1: 10c00000-10fff000 I/O window 0: 00004800-000048ff I/O window 1: 00004c00-00004cff BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ PostWrite+ 16-bit legacy interface ports at 0001 00:03.0 Ethernet controller: Intel Corp. 82557 [Ethernet Pro 100] (rev 09) Subsystem: Intel Corp.: Unknown device 2408 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 66 (2000ns min, 14000ns max), cache line size 08 Interrupt: pin A routed to IRQ 10 Region 0: Memory at e8120000 (32-bit, non-prefetchable) [size=4K] Region 1: I/O ports at 1800 [size=64] Region 2: Memory at e8100000 (32-bit, non-prefetchable) [size=128K] Expansion ROM at <unassigned> [disabled] [size=1M] Capabilities: <available only to root> 00:03.1 Serial controller: Xircom: Unknown device 000c (prog-if 02 [16550]) Subsystem: Intel Corp.: Unknown device 2408 Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Interrupt: pin A routed to IRQ 10 Region 0: I/O ports at 1840 [size=8] Region 1: Memory at e8121000 (32-bit, non-prefetchable) [size=4K] Capabilities: <available only to root> 00:05.0 Multimedia audio controller: Cirrus Logic CS 4614/22/24 [CrystalClear SoundFusion Audio Accelerator] (rev 01) Subsystem: IBM: Unknown device 0153 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 64 (1000ns min, 6000ns max) Interrupt: pin A routed to IRQ 10 Region 0: Memory at e8122000 (32-bit, non-prefetchable) [size=4K] Region 1: Memory at e8000000 (32-bit, non-prefetchable) [size=1M] Capabilities: <available only to root> 00:07.0 Bridge: Intel Corp. 82371AB PIIX4 ISA (rev 02) Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 00:07.1 IDE interface: Intel Corp. 82371AB PIIX4 IDE (rev 01) (prog-if 80 [Master]) Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 64 Region 4: I/O ports at 1850 [size=16] 00:07.2 USB Controller: Intel Corp. 82371AB PIIX4 USB (rev 01) (prog-if 00 [UHCI]) Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 64 Interrupt: pin D routed to IRQ 10 Region 4: I/O ports at 1860 [size=32] 00:07.3 Bridge: Intel Corp. 82371AB PIIX4 ACPI (rev 03) Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Interrupt: pin ? routed to IRQ 9 01:00.0 VGA compatible controller: S3 Inc. 86C270-294 Savage/IX-MV (rev 11) (prog-if 00 [VGA]) Subsystem: IBM: Unknown device 017f Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 64 (1000ns min, 63750ns max), cache line size 08 Interrupt: pin A routed to IRQ 10 Region 0: Memory at f0000000 (32-bit, non-prefetchable) [size=128M] Expansion ROM at <unassigned> [disabled] [size=64K] Capabilities: <available only to root> |
