[Serial-pci-info] lspci -vv

SourceForge Headquarters 1320 Columbia Street Suite 310 San Diego, CA 92101 +1 (858) 422-6466

Per instructions i recieved in 'dmesg' i am sending some pci info, hope it helps
This is a new clean 'ftp' install of Debian 'Woody' 3.0 kernel 2.4.18-bf2.4 on a i586. Compaq
Presario 7471 'AMD' with 320MB RAM. (Hardly a new machine but the info may be useful)

<snip='dmesg'>
PCI: Found IRQ 10 for device 00:0a.0
Redundant entry in serial pci_table.  Please send the output of
lspci -vv, this message (134d,7897,134d,0001)
and the manufacturer and name of serial board or modem board
to ser...@li....
register_serial(): autoconfig failed
</snip>

# sudo lspci -vv
00:00.0 Host bridge: VIA Technologies, Inc. VT8501 [Apollo MVP4] (rev 03)
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
	Latency: 16
	Region 0: Memory at 50000000 (32-bit, prefetchable) [size=64M]
	Capabilities: [a0] AGP version 2.0
		Status: RQ=7 SBA+ 64bit- FW- Rate=x1,x2
		Command: RQ=0 SBA- AGP+ 64bit- FW- Rate=<none>

00:01.0 PCI bridge: VIA Technologies, Inc. VT8501 [Apollo MVP4 AGP] (prog-if 00 [Normal decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap- 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR+
	Latency: 0
	Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
	Memory behind bridge: 40000000-410fffff
	BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-

00:07.0 ISA bridge: VIA Technologies, Inc. VT82C686 [Apollo Super South] (rev 14)
	Subsystem: Unknown device 0011:0000
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B-
	Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 0

00:07.1 IDE interface: VIA Technologies, Inc. Bus Master IDE (rev 06) (prog-if 8a [Master SecP PriP])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 66
	Region 4: I/O ports at 1c80 [size=16]

00:07.2 USB Controller: VIA Technologies, Inc. UHCI USB (rev 06) (prog-if 00 [UHCI])
	Subsystem: Unknown device 0925:1234
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 66, cache line size 08
	Interrupt: pin D routed to IRQ 11
	Region 4: I/O ports at 1c40 [size=32]

00:07.3 USB Controller: VIA Technologies, Inc. UHCI USB (rev 06) (prog-if 00 [UHCI])
	Subsystem: Unknown device 0925:1234
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 66, cache line size 08
	Interrupt: pin D routed to IRQ 11
	Region 4: I/O ports at 1c60 [size=32]

00:07.4 Bridge: VIA Technologies, Inc. VT82C686 [Apollo Super ACPI] (rev 10)
	Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-

00:08.0 VGA compatible controller: S3 Inc. ViRGE/DX or /GX (rev 01) (prog-if 00 [VGA])
	Subsystem: STB Systems Inc Nitro 3D
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 64 (1000ns min, 63750ns max)
	Interrupt: pin A routed to IRQ 3
	Region 0: Memory at 44000000 (32-bit, non-prefetchable) [size=64M]
	Expansion ROM at <unassigned> [disabled] [size=64K]

00:09.0 Ethernet controller: Accton Technology Corporation SMC2-1211TX (rev 10)
	Subsystem: Accton Technology Corporation EN-1207D Fast Ethernet Adapter
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 66 (8000ns min, 16000ns max)
	Interrupt: pin A routed to IRQ 5
	Region 0: I/O ports at 1000 [size=256]
	Region 1: Memory at 41100000 (32-bit, non-prefetchable) [size=256]
	Capabilities: [50] Power Management version 1
		Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1+,D2+,D3hot+,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:0a.0 Modem: PCTel Inc HSP MicroModem 56 (rev 02) (prog-if 01 [Hayes/16450])
	Subsystem: PCTel Inc: Unknown device 0001
	Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Interrupt: pin A routed to IRQ 10
	Region 0: I/O ports at 1c00 [size=64]
	Capabilities: [40] Power Management version 2
		Flags: PMEClk- DSI+ D1- D2+ AuxCurrent=55mA PME(D0+,D1-,D2+,D3hot+,D3cold+)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:0b.0 Ethernet controller: Accton Technology Corporation SMC2-1211TX (rev 10)
	Subsystem: Accton Technology Corporation EN-1207D Fast Ethernet Adapter
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 66 (8000ns min, 16000ns max)
	Interrupt: pin A routed to IRQ 11
	Region 0: I/O ports at 1400 [size=256]
	Region 1: Memory at 41200000 (32-bit, non-prefetchable) [size=256]
	Expansion ROM at <unassigned> [disabled] [size=64K]
	Capabilities: [50] Power Management version 2
		Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:0d.0 Multimedia audio controller: ESS Technology ES1988 Allegro-1 (rev 10)
	Subsystem: Compaq Computer Corporation: Unknown device b207
	Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 64 (500ns min, 6000ns max)
	Interrupt: pin A routed to IRQ 5
	Region 0: I/O ports at 1800 [size=256]
	Capabilities: [c0] Power Management version 2
		Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0-,D1+,D2+,D3hot+,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

01:00.0 VGA compatible controller: Trident Microsystems CyberBlade/i7 (rev 5c) (prog-if 00 [VGA])
	Subsystem: Compaq Computer Corporation: Unknown device b1ab
	Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 64
	Interrupt: pin A routed to IRQ 3
	Region 0: Memory at 40000000 (32-bit, non-prefetchable) [disabled] [size=8M]
	Region 1: Memory at 41000000 (32-bit, non-prefetchable) [disabled] [size=128K]
	Region 2: Memory at 40800000 (32-bit, non-prefetchable) [disabled] [size=8M]
	Expansion ROM at <unassigned> [disabled] [size=64K]
	Capabilities: [80] AGP version 1.0
		Status: RQ=32 SBA+ 64bit- FW- Rate=x1,x2
		Command: RQ=0 SBA- AGP- 64bit- FW- Rate=<none>
	Capabilities: [90] Power Management version 1
		Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-